Test report-DTS Part1

FCC ID: 2AL9D-FIP16

Test Report

Download: PDF
FCCID_4179854

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 E-mail: ctl@ctl-lab.com TEST REPORT FCC PART 15.247 Report Reference No. ................ : CTL1811027021-WF01 Compiled by: Happy Guo ( position+printed name+signature) (File administrators) Tested by: Nice Nong ( position+printed name+signature) (Test Engineer) Approved by: Ivan Xie ( position+printed name+signature) (Manager) Product Name ............................ : Portable Wireless IP PHONE Model/Type reference ................ : FIP16 List Model(s) ............................... : N/A Trade Mark .................................. : FCC ID......................................... : 2AL9D-FIP16 Applicant’s name ....................... : Flyingvoice Network Technology Co., Ltd Rm 207-209, Unt B52, Zhong Chuang Industrial Park, Nanshan Address of applicant ................. : District, Shenzhen, China Test Firm ..................................... : Shenzhen CTL Testing Technology Co., Ltd. Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Address of Test Firm ................. : Nanshan District, Shenzhen, China 518055 Test specification ....................... : Standard ...................................... : FCC Part 15.247: Operation within the bands 902-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz. TRF Originator ............................. : Shenzhen CTL Testing Technology Co., Ltd. Master TRF .................................. : Dated 2011-01 Date of Receipt ........................... : Nov. 02, 2018 Date of Test Date ........................ : Nov. 02, 2018–Dec. 19, 2018 Data of Issue............................... : Jan. 18, 2019 Result.......................................... : Pass Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.

V1.0 Page 2 of 42 Report No.: CTL181102702-WF01 TEST REPORT Jan. 18, 2019 Test Report No. : CTL181102702-WF01 Date of issue Equipment under Test : Portable Wireless IP PHONE Model /Type : FIP16 Listed Models : N/A Applicant : Flyingvoice Network Technology Co., Ltd Address : Rm 207-209, Unt B52, Zhong Chuang Industrial Park, Nanshan District, Shenzhen, China Manufacturer : Flyingvoice Network Technology Co., Ltd Address : Rm 207-209, Unt B52, Zhong Chuang Industrial Park, Nanshan District, Shenzhen, China Test result Pass * * In the configuration tested, the EUT complied with the standards specified page 5. The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

V1.0 Page 3 of 42 Report No.: CTL181102702-WF01 ** Modified History ** Revisions Description Issued Data Report No. Remark Version 1.0 Initial Test Report Release 2019-01-18 CTL1811027021-WF01 Tracy Qi

V1.0 Page 4 of 42 Report No.: CTL181102702-WF01 Table of Contents Page 1. SUMMARY ............................................................................................................................................................... 5 1.1. TEST STANDARDS ..................................................................................................................................................... 5 1.2. TEST DESCRIPTION........................................................................................................................................................ 5 1.3. TEST FACILITY .............................................................................................................................................................. 6 1.4. STATEMENT OF THE MEASUREMENT UNCERTAINTY............................................................................................................... 6 2. GENERAL INFORMATION .......................................................................................................................................... 7 2.1. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 7 2.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 7 2.3. DESCRIPTION OF TEST MODES AND TEST FREQUENCY.......................................................................................................... 7 2.4. EQUIPMENTS USED DURING THE TEST .............................................................................................................................. 8 2.5. SPECIAL ACCESSORIES ................................................................................................................................................... 9 2.6. RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................................................ 9 2.7. MODIFICATIONS ........................................................................................................................................................... 9 3. TEST CONDITIONS AND RESULTS ............................................................................................................................ 10 3.1. CONDUCTED EMISSIONS TEST ....................................................................................................................................... 10 3.2. RADIATED EMISSIONS AND BAND EDGE .......................................................................................................................... 13 3.3. MAXIMUM CONDUCTED OUTPUT POWER....................................................................................................................... 20 3.4. POWER SPECTRAL DENSITY .......................................................................................................................................... 21 3.5. 6DB BANDWIDTH....................................................................................................................................................... 24 3.6. OUT-OF-BAND EMISSIONS ........................................................................................................................................... 27 3.7. ANTENNA REQUIREMENT ............................................................................................................................................. 36 4. TEST SETUP PHOTOS OF THE EUT ........................................................................................................................... 37 5. PHOTOS OF THE EUT .............................................................................................................................................. 38

V1.0 Page 5 of 42 Report No.: CTL181102702-WF01 1. SUMMARY 1.1. TEST STANDARDS The tests were performed according to following standards: FCC Rules Part 15.247: Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz ANSI C63.10: 2013: American National Standard for Testing Unlicensed Wireless Devices KDB558074 D01 V05: Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247 1.2. Test Description FCC PART 15.247 FCC Part 15.207 AC Power Conducted Emission PASS FCC Part 15.247(a)(2) 6dB Bandwidth PASS FCC Part 15.247(d) Spurious RF Conducted Emission PASS FCC Part 15.247(b) Maximum Conducted Output Power PASS FCC Part 15.247(e) Power Spectral Density PASS FCC Part 15.109/ 15.205/ 15.209 Radiated Emissions PASS FCC Part 15.247(d) Band Edge PASS FCC Part 15.203/15.247 (b) Antenna Requirement PASS

V1.0 Page 6 of 42 Report No.: CTL181102702-WF01 1.3. Test Facility 1.3.1 Address of the test laboratory Shenzhen CTL Testing Technology Co., Ltd. Floor 1-A, Baisha Technology Park, No. 3011, Shahexi Road, Nanshan, Shenzhen 518055 China The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.4:2014 and CISPR 16-1-4:2010 SVSWR requirement for radiated emission above 1GHz. 1.3.2 Laboratory accreditation The test facility is recognized, certified, or accredited by the following organizations: IC Registration No.: 9618B The 3m alternate test site of Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered by Certification and Engineer Bureau of Industry Canada for the performance of with Registration No.: 9618B on November 13, 2013. FCC-Registration No.: 399832 Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration 399832, December 08, 2017. 1.4. Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to CISPR 16 - 4 “Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements“ and is documented in the Shenzhen CTL Testing Technology Co., Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for CTL laboratory is reported: Measurement Test Notes Uncertainty Transmitter power conducted ±0.57 dB (1) Transmitter power Radiated ±2.20 dB (1) Conducted spurious emission 9KHz-40 GHz ±2.20 dB (1) Occupied Bandwidth ±0.01ppm (1) Radiated Emission 30~1000MHz ±4.10dB (1) Radiated Emission Above 1GHz ±4.32dB (1) Conducted Disturbance0.15~30MHz ±3.20dB (1) (1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

V1.0 Page 7 of 42 Report No.: CTL181102702-WF01 2. GENERAL INFORMATION 2.1. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature: 25°C Relative Humidity: 55 % Air Pressure: 101 kPa 2.2. General Description of EUT Product Name: Portable Wireless IP PHONE Model/Type reference: FIP16 Power supply: 5V/1A, Battery 3.8V 4400mAh WIFI : Supported type: 802.11b/802.11g/802.11n(H20)/802.11n(H40) 802.11b: DSSS Modulation: 802.11g/802.11n(H20)/802.11n(H40): OFDM 802.11b/802.11g/802.11n(H20): 2412MHz~2462MHz Operation frequency: 802.11n(H40): 2422MHz~2452MHz 802.11b/802.11g/802.11n(H20): 11 Channel number: 802.11n(H40): 7 Channel separation: 5MHz Antenna type: FPC antenna Antenna gain: 0dBi Note: For more details, please refer to the user’s manual of the EUT. 2.3. Description of Test Modes and Test Frequency The Applicant provides communication tools software to control the EUT for staying in continuous transmitting (Duty Cycle more than 98%) and receiving mode for testing. There are 11 channels provided to the EUT and Channel 01/06/11 were selected for WIFI test. Operation Frequency WIFI： Channel Frequency(MHz) Channel Frequency(MHz) 1 2412 8 2447 2 2417 9 2452 3 2422 10 2457 4 2427 11 2462 5 2432 6 2437 7 2442 Note: The line display in grey were the channel selected for testing

V1.0 Page 8 of 42 Report No.: CTL181102702-WF01 Data Rate Used: Preliminary tests were performed in different data rate to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Test Items Mode Data Rate Channel 11b/DSSS 1 Mbps 1/6/11 Maximum Conducted Output Power Power Spectral Density 11g/OFDM 6 Mbps 1/6/11 6dB Bandwidth Spurious RF conducted emission 11n(20MHz)/OFDM 6.5Mbps 1/6/11 Radiated Emission 9kHz~1GHz& Radiated Emission 1GHz~10th Harmonic 11n(40MHz)/OFDM 13.5Mbps 3/6/9 11b/DSSS 1 Mbps 1/11 11g/OFDM 6 Mbps 1/11 Band Edge 11n(20MHz)/OFDM 6.5Mbps 1/11 11n(40MHz)/OFDM 13.5Mbps 3/9 2.4. Equipments Used during the Test Calibration Calibration Test Equipment Manufacturer Model No. Serial No. Date recent Due Date LISN R&S ENV216 3560.6550.12 2018/06/01 2019/05/31 LISN R&S ESH2-Z5 860014/010 2018/06/01 2019/05/31 Power Meter Agilent U2531A TW53323507 2018/06/01 2019/05/31 Power Sensor Agilent U2021XA MY5365004 2018/05/20 2019/05/19 EMI Test Receiver R&S ESCI 103710 2018/06/01 2019/05/31 Spectrum Analyzer Agilent E4407B MY41440676 2018/05/20 2019/05/19 Spectrum Analyzer Agilent N9020 US46220290 2018/01/16 2019/01/15 Controller EM Electronics Controller EM 1000 N/A 2018/05/20 2019/05/19 Active Loop Antenna Daze ZN30900A N/A 2018/05/18 2019/05/17 Bilog Antenna Schwarzbeck VULB 9168 00824 2018/10/25 2019/10/24 Sunol Sciences Horn Antenna DRH-118 A062013 2018/05/18 2019/05/17 Corp. Horn Antenna SCHWARZBACK BBHA 9170 BBHA9170184 2018/05/18 2019/05/17 Amplifier Agilent 8349B 3008A02306 2018/05/18 2019/05/17 Amplifier Agilent 8447D 2944A10176 2018/05/18 2019/05/17 Temperature/Humidity Gangxing CTH-608 02 2018/05/19 2019/05/18 Meter High-Pass Filter K&L 9SH10-2700/X12750-O/O N/A 2018/05/19 2019/05/18 High-Pass Filter K&L 41H10-1375/U12750-O/O N/A 2018/05/19 2019/05/18 SUCOFLEX 2018/06/01 2019/05/31 Coaxial Cables HUBER+SUHNER 10m 104PEA-10M Coaxial Cables HUBER+SUHNER SUCOFLEX 104PEA-3M 3m 2018/06/01 2019/05/31 Coaxial Cables HUBER+SUHNER SUCOFLEX 104PEA-3M 3m 2018/06/01 2019/05/31 RF Cable Megalon RF-A303 N/A 2018/06/01 2019/05/31

V1.0 Page 9 of 42 Report No.: CTL181102702-WF01 EMI Test Software R&S ES-K1 V1.7.1 2018/06/01 2019/05/31 EMI Test Software AUDIX E3 V6.0 2018/06/01 2019/05/31 The calibration interval was one year 2.5. Special Accessories Manufacturer Description Model Serial Number Certificate ASUS Notebook PC FL5900U 9014 FCC ID:PPD-QCNFA335 Delta AC Adapter S12B22-120A100-C4 00A99 SDOC 2.6. Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended to comply with Section 15.247 of the FCC Part 15, Subpart C Rules. 2.7. Modifications No modifications were implemented to meet testing criteria.

vio Page 10 of 42 Report No.: CTL181102702—WE01 3. TEST CONDITIONS AND RESULTS 3.1. Conducted Emissions Test LiMIT FCC CFR Title 47 Part 15 Subpart C Section 15.207 Limt (dBuv) Frequency range (MHz) Quas—peak Average 0.15.0.5 66 to 56° 56 to 46° 055 56 46 5.30 so 5o * Decreases with the logarithm ofthe frequency TEST CONFIGURATION Shilded Room: eur Tes i Recaver 18m uisw [ [=<] TesT PRoCEDURE 1. The equipment was set up as per the test configuration to simulate bpical actual usage per the user‘s manual.The EUT is a tabletop system; a wooden table with a height of .8 meters is used and is placed on the ground plane as per ANSI C63.10:2013 2. Support equipmentif needed, was placed as per ANSI C63.10.2013 AlllID cables were positoned to smulate bypical actual usage as per ANSI C63.10:2013 4. The adapter received AC120V/60Hz powerthrough a Line Impedance Stablization Network (LISN) which supplied power source and was grounded to the ground plane 5. All support equipments received AC powerfrom a second LISN, if any. 8. The EUT test program was statted. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver comnected to the LISN powering the EUT.. The LISN has two monitaring paints. Line 1 (Hot Side) and Line 2 (Neutral Side)...Two scanswere taken one wih Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load, the secand scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer/ Receiver. 7. Analyzer / Receiver scanned from 150 Kz to 0MH for emissionsin each of the test modes 8. During the above scans,the emisions vere maximized by cable manipulation

V1.0 Page 11 of 42 Report No.: CTL181102702-WF01 TEST RESULTS Remark: 1. All modes of 802.11b/g/n were tested at Low, Middle, and High channel; only the worst result of 802.11b CH11 was reported as below: 2. Both 120 VAC, 50/60 Hz and 240 VAC, 50/60 Hz power supply have been tested, only the worst result of 120 VAC, 60 Hz was reported as below: Test Mode WIFI Line: L

SCAN TABLE: "Voltage (I9K—30M)FIN" Short Description: 150R— 30M Level [dBp¥y] 70 6D 50L ———L——== I I I 1oooad 40 | | I ED-W _MMGU L n T 4 1 I I I I heCE Dprenionafotibe fopninte I I I Io— oA d | | | | | 1o o l U "||:| o — — —o Lo se se se se se h se e se foo e se Je s e s f s J —]s I I I I I Lo d d I I I I I I I I Lo d d I I I I 0 1 1 1 1 1 |L_ L | | | | | 1 150k 300k 400k 600k 800k 1 1 2M 3M 4M 5M 6M 8M 10M 20M 30M ze® Frequency [Hz] x x x MES CTLL31117233_fin MEASUREMENT RESULT: "CTL181117233_fin" =, 2018—11—17 0414 «: w# "A J Frequency "Ld =vel Transd Limit Margin Detector Line PE MEz dBuv dB dBypv dB 0 , 154000 12 .60 10 .2 66 23.2 Q N GND 0. 222000 34 .60 10 .2 €3 28.1 9 N GND 0. 234000 34. 10 10 .2 62 28.2 0 N GND 0 , 506000 34 .00 10 .2 36 2a2a.0 Q N GND MEASUREMENT RESULT: "CTL181117233_fin2" =, ~, 2018—11—17 0414 =5.d «: w# Frequency "Ld =vel Transd Limit Margin Detector Line PE MEz dBuy dB dBuv dB 0 , 1350000 29.90 10 , 36 E AV N GND J l J J hJ hJ hJ3 |— i _3 oi— —=J —f— i 0 , 500000 24.40 10 , 4C AV N GND DJ §3 1. 382000 18 .50 10. CGND GjJ is C3 UNT is4 I___.‘I 168000 14 .40 10. CGND [~3 JS is c\ § L1 4 id 17. 924000 17 .10 10. CGND 3 03 tb iEL is4 es e 7 .9 i3 LN 18 .40 10. m CGND £_.£3 Ci+4 es d

V1.0 Page 13 of 42 Report No.: CTL181102702-WF01 3.2. Radiated Emissions and Band Edge Limit For intentional device, according to § 15.209(a), the general requirement of field strength of radiated emission out of authorized band shall not exceed the following table at a 3 meters measurement distance. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) Radiated emission limits Frequency (MHz) Distance (Meters) Radiated (dBμV/m) Radiated (μV/m) 0.009-0.49 3 20log(2400/F(KHz))+40log(300/3) 2400/F(KHz) 0.49-1.705 3 20log(24000/F(KHz))+ 40log(30/3) 24000/F(KHz) 1.705-30 3 20log(30)+ 40log(30/3) 30 30-88 3 40.0 100 88-216 3 43.5 150 216-960 3 46.0 200 Above 960 3 54.0 500 TEST CONFIGURATION (A) Radiated Emission Test Set-Up, Frequency Below 30MHz (B) Radiated Emission Test Set-Up, Frequency below 1000MHz (C) Radiated Emission Test Set-Up, Frequency above 1000MHz

V1.0 Page 14 of 42 Report No.: CTL181102702-WF01 Test Procedure 1. Below 1GHz measurement the EUT is placed on a turntable which is 0.8m above ground plane, and above 1GHz measurement EUT was placed on a low permittivity and low loss tangent turn table which is 1.5m above ground plane. 2. Maximum procedure was performed by raising the receiving antenna from 1m to 4m and rotating the turn table from 0℃ to 360℃ to acquire the highest emissions from EUT 3. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 4. Repeat above procedures until all frequency measurements have been completed. 5. Radiated emission test frequency band from 9KHz to 25GHz. 6. The distance between test antenna and EUT as following table states: Test Frequency range Test Antenna Type Test Distance 9KHz-30MHz Active Loop Antenna 3 30MHz-1GHz Bilog Antenna 3 1GHz-18GHz Horn Antenna 3 18GHz-25GHz Horn Antenna 1 7. Setting test receiver/spectrum as following table states: Test Frequency Test Receiver/Spectrum Setting Detector range 9KHz-150KHz RBW=200Hz/VBW=3KHz,Sweep time=Auto QP 150KHz-30MHz RBW=9KHz/VBW=100KHz,Sweep time=Auto QP RBW=120KHz/VBW=1000KHz,Sweep 30MHz-1GHz QP time=Auto Peak Value: RBW=1MHz/VBW=3MHz, Sweep time=Auto 1GHz-40GHz Peak Average Value: RBW=1MHz/VBW=10Hz, Sweep time=Auto TEST RESULTS Remark: 1. This test was performed with EUT in X, Y, Z position and the worse case was found when EUT in X position. 2. All three channels (lowest/middle/highest) of each mode were measured below 1GHz and recorded worst case at 802.11b low channel. 3. All three channels (lowest/middle/highest) of each mode were measured above1GHz and recorded worst case at 802.11b mode. 4. Radiated emission test from 9 KHz to 10th harmonic of fundamental was verified, and no emission found except system noise floor in 9 KHz to 30MHz and not recorded in this report.

V1.0 Page 15 of 42 Report No.: CTL181102702-WF01 For 30MHz-1GHz Test mode: WIFI Polarization: Horizontal Test mode: WIFI Polarization: Vertical

V1.0 Page 16 of 42 Report No.: CTL181102702-WF01 For 1GHz to 25GHz 802.11b Mode (above 1GHz) Note: 802.11b/802.11g/802.11n (H20)/802.11n (H40) all have been tested, only worse case 802.11b is reported Frequency(MHz): 2412 Polarity: HORIZONTAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4824.00 55.47 PK 74 18.53 50.92 33.52 6.92 35.89 4.55 4824.00 48.66 AV 54 5.34 44.11 33.52 6.92 35.89 4.55 6811.00 46.91 PK 74 27.09 37.08 36.01 8.81 34.99 9.83 6811.00 -- AV 54 -- -- -- -- -- -- 7236.00 47.50 PK 74 26.50 36.23 37.10 9.19 35.02 11.27 7236.00 -- AV 54 -- -- -- -- -- -- Frequency(MHz): 2412 Polarity: VERTICAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4824.00 55.10 PK 74 18.90 50.55 33.52 6.92 35.89 4.55 4824.00 47.59 AV 54 6.41 43.04 33.52 6.92 35.89 4.55 5702.00 48.06 PK 74 25.94 40.33 34.79 7.42 34.48 7.73 5702.00 -- AV 54 -- -- -- -- -- -- 7236.00 45.70 PK 74 28.30 34.43 37.10 9.19 35.02 11.27 7236.00 -- AV 54 -- -- -- -- -- -- Frequency(MHz): 2437 Polarity: HORIZONTAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4874.00 55.51 PK 74 18.49 50.87 33.59 6.95 35.90 4.64 4874.00 48.46 AV 54 5.54 43.82 33.59 6.95 35.90 4.64 6207.00 46.85 PK 74 27.15 38.44 35.19 7.91 34.69 8.41 6207.00 -- AV 54 -- -- -- -- -- -- 7311.00 47.30 PK 74 26.70 35.64 37.44 9.22 35.00 11.66 7311.00 -- AV 54 -- -- -- -- -- -- Frequency(MHz): 2437 Polarity: VERTICAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4874.00 54.68 PK 74 19.32 50.04 33.59 6.95 35.90 4.64 4874.00 46.78 AV 54 7.22 42.14 33.59 6.95 35.90 4.64 6038.00 47.39 PK 74 26.61 39.20 35.15 7.65 34.61 8.19 6038.00 -- AV 54 -- -- -- -- -- -- 7311.00 45.12 PK 74 28.88 33.46 37.44 9.22 35.00 11.66 7311.00 -- AV 54 -- -- -- -- -- --

V1.0 Page 17 of 42 Report No.: CTL181102702-WF01 Frequency(MHz): 2462 Polarity: HORIZONTAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4924.00 54.85 PK 74 19.15 50.07 33.71 6.98 35.91 4.78 4924.00 47.20 AV 54 6.80 42.42 33.71 6.98 35.91 4.78 6930.00 44.98 PK 74 29.02 34.87 36.16 9.00 35.05 10.11 6930.00 -- AV 54 -- -- -- -- -- -- 7386.00 46.15 PK 74 27.85 34.27 37.61 9.25 34.98 11.88 7386.00 -- AV 54 -- -- -- -- -- -- Frequency(MHz): 2462 Polarity: VERTICAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4924.00 55.08 PK 74 18.92 50.30 33.71 6.98 35.91 4.78 4924.00 47.10 AV 54 6.90 42.32 33.71 6.98 35.91 4.78 5359.00 45.53 PK 74 28.47 37.95 34.70 7.24 34.36 7.58 5359.00 -- AV 54 -- -- -- -- -- -- 7386.00 47.49 PK 74 26.51 35.61 37.61 9.25 34.98 11.88 7386.00 -- AV 54 -- -- -- -- -- -- REMARKS: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. 6. RBW1MHz VBW3MHz Peak detector is for PK value; RBW 1MHz VBW10Hz Peak detector is for AV value.

V1.0 Page 18 of 42 Report No.: CTL181102702-WF01 Results of Band Edges Test (Radiated) Note: 802.11b/802.11g/802.11n (H20)/802.11n (H40) all have been tested, only worse case 802.11b is reported Frequency(MHz): 2412 Polarity: HORIZONTAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2412.00 101.98 PK -- -- 68.56 28.80 4.62 0.00 33.42 2412.00 92.15 AV -- -- 58.73 28.80 4.62 0.00 33.42 2373.00 44.83 PK 74 29.17 11.64 28.61 4.58 0.00 33.19 2373.00 -- AV 54 -- -- -- -- -- -- 2390.00 46.57 PK 74 27.43 13.25 28.72 4.60 0.00 33.32 2390.00 -- AV 54 -- -- -- -- -- -- 2400.00 55.69 PK 74 18.31 22.30 28.78 4.61 0.00 33.39 2400.00 48.46 AV 54 5.54 15.07 28.78 4.61 0.00 33.39 Frequency(MHz): 2412 Polarity: VERTICAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2412.00 101.09 PK -- -- 67.67 28.80 4.62 0.00 33.42 2412.00 91.59 AV -- -- 58.17 28.80 4.62 0.00 33.42 2373.00 43.70 PK 74 30.30 10.51 28.61 4.58 0.00 33.19 2373.00 -- AV 54 -- -- -- -- -- -- 2390.00 45.54 PK 74 28.46 12.22 28.72 4.60 0.00 33.32 2390.00 -- AV 54 -- -- -- -- -- -- 2400.00 54.08 PK 74 19.92 20.69 28.78 4.61 0.00 33.39 2400.00 46.36 AV 54 7.64 12.97 28.78 4.61 0.00 33.39 Frequency(MHz): 2462 Polarity: HORIZONTAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2462.00 100.58 PK -- -- 67.01 28.89 4.68 0.00 33.57 2462.00 92.16 AV -- -- 58.59 28.89 4.68 0.00 33.57 2483.50 54.27 PK 74 19.73 20.64 28.93 4.70 0.00 33.63 2483.50 47.65 AV 54 6.35 14.02 28.93 4.70 0.00 33.63 2492.00 46.51 PK 74 27.49 12.85 28.95 4.71 0.00 33.66 2492.00 -- AV 54 -- -- -- -- -- -- 2500.00 42.12 PK 74 31.88 8.44 28.96 4.72 0.00 33.68 2500.00 -- AV 54 -- -- -- -- -- --

V1.0 Page 19 of 42 Report No.: CTL181102702-WF01 Frequency(MHz): 2462 Polarity: VERTICAL Emission Raw Antenna Cable Correction Frequency Limit Margin Pre-amplifier Level Value Factor Factor Factor (MHz) (dBuV/m) (dB) (dB) (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2462.00 100.06 PK -- -- 66.49 28.89 4.68 0.00 33.57 2462.00 91.58 AV -- -- 58.01 28.89 4.68 0.00 33.57 2483.50 54.02 PK 74 19.98 20.39 28.93 4.70 0.00 33.63 2483.50 46.67 AV 54 7.33 13.04 28.93 4.70 0.00 33.63 2492.00 44.32 PK 74 29.68 10.66 28.95 4.71 0.00 33.66 2492.00 -- AV 54 -- -- -- -- -- -- 2500.00 41.87 PK 74 32.13 8.19 28.96 4.72 0.00 33.68 2500.00 -- AV 54 -- -- -- -- -- -- REMARKS: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. 6. RBW1MHz VBW3MHz Peak detector is for PK value; RBW 1MHz VBW10Hz Peak detector is for AV value. 7. For fundamental frequency, RBW 3MHz VBW 3MHz Peak detector is for PK Value; RMS detector is for AV value.

V1.0 Page 20 of 42 Report No.: CTL181102702-WF01 3.3. Maximum Conducted Output Power Limit The Maximum Peak Output Power Measurement is 30dBm. Test Procedure Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the power sensor. Test Configuration EUT Power Sensor Power Meter Test Results WIFI Output power PK Type Channel Limit (dBm) Result (dBm) 01 9.43 802.11b 06 9.39 30.00 Pass 11 9.03 01 9.21 802.11g 06 8.79 30.00 Pass 11 8.36 01 8.90 802.11n(HT20) 06 8.49 30.00 Pass 11 8.08 03 7.93 802.11n(HT40) 06 8.35 30.00 Pass 09 8.16 Note: 1.The test results including the cable lose.

V1.0 Page 21 of 42 Report No.: CTL181102702-WF01 3.4. Power Spectral Density Limit For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. Test Procedure 1. Use this procedure when the maximum peak conducted output power in the fundamental emission is used to demonstrate compliance. 2. Set the RBW ≥ 3 kHz. 3. Set the VBW ≥ 3× RBW. 4. Set the span to 1.5 times the DTS channel bandwidth. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum power level. 10. If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. 11. The resulting peak PSD level must be 8dBm. Test Configuration EUT SPECTRUM ANALYZER Test Results WIFI Power Spectral Density Type Channel Limit (dBm/3KHz) Result (dBm/3KHz) 01 -19.961 802.11b 06 -20.128 8.00 Pass 11 -21.461 01 -27.551 802.11g 06 -28.557 8.00 Pass 11 -29.038 01 -28.577 802.11n(HT20) 06 -27.839 8.00 Pass 11 -28.974 03 -33.158 802.11n(HT40) 06 -32.436 8.00 Pass 09 -33.077 Test plot as follows:

V1.0 Page 22 of 42 Report No.: CTL181102702-WF01 802.11b 802.11g CH01 CH01 CH06 CH06 CH11 CH11

V1.0 Page 23 of 42 Report No.: CTL181102702-WF01 802.11n(HT20) 802.11n(HT40) CH01 CH03 CH06 CH06 CH11 CH09

V1.0 Page 24 of 42 Report No.: CTL181102702-WF01 3.5. 6dB Bandwidth Limit For digital modulation systems, the minimum 6 dB bandwidth shall be at least 500 kHz Test Procedure The transmitter output was connected to the spectrum analyzer through an attenuator. The bandwidth of the fundamental frequency was measured by spectrum analyzer with 100 KHz RBW and 300 KHz VBW. The 6dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 6dB. Test Configuration EUT SPECTRUM ANALYZER Test Results WIFI 6dB Bandwidth 99% OBW Limit Type Channel Result (MHz) (MHz) (KHz) 01 10.23 14.350 802.11b 06 10.23 14.406 ≥500 Pass 11 10.23 14.405 01 16.41 16.390 802.11g 06 16.41 16.387 ≥500 Pass 11 16.40 16.380 01 17.16 17.493 802.11n(HT20) 06 17.14 17.478 ≥500 Pass 11 17.20 17.498 03 36.00 35.966 802.11n(HT40) 06 35.64 35.998 ≥500 Pass 09 35.99 36.057 Test plot as follows:

V1.0 Page 25 of 42 Report No.: CTL181102702-WF01 802.11b 802.11g CH01 CH01 CH06 CH06 CH11 CH11

V1.0 Page 26 of 42 Report No.: CTL181102702-WF01 802.11n(HT20) 802.11n(HT40) CH01 CH03 CH06 CH06 CH11 CH09


Document Created: 2019-09-24 06:12:06
Document Modified: 2019-09-24 06:12:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC