Test report

FCC ID: 2AKMKMCA021

Test Report

Download: PDF
FCCID_3250734

i Microfest Infernational FCC ID: 2AKMKMCAO21 Date of issue: Dec. 05, 2016 Sample Description: mCookie Module BLE Upload Model(s): MCAO21, MDAO21 Applicant: Microduino Inc. L 2659 Townsgate Rd. #213, Westlake Village, Address: CA91361, USA Date of Test: Dec. 01, 2016 to Dec. 04, 2016 Shenzhen Microtest Co., Ltd. http://www.mtitest.com This test report is valld for the tested samples only. it cannot be reproduced except in full without prior witten consent of Shenzhen Mieratest Co., Ltd Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 2 of 23 — Report No.: MTi161201E001 Table of Contents Table of Contents 1 G@N@FAL A@SCTIDNION................cceseeseen en en en en en en mm mm mm mm mm mm mm mm mm ennennencenne 5 1.1 Feature of equipment under test (EUT)... 1.2 Operation channel list....................lllll. 1.3 TStTEGUBNGY CR@BMM@L...............lsccncencencencencencenv enc nnc mm nc nc nc nne nc nnennennc nc nnc nc nnenncncncncen 5 1.4 EUT operation mode 1.5 Test conditions....... 1.6 ANGIIIQTY @QUIDM@NE lt .............. 0000c cencencencencencencnnc mm nc nnc nc nc nc nnc nc nne nc nncnncnne mm nc ncncen 6 1.7.= ME@SUIEM@NE UNGETE@IATY ........... .cs lcccccncencencencencencenc enc nnc mm enc nnc enc nne nc nne nc nne enc nnennennc nc ncnncens 6 P Co1 ) e 7 3 LiSt Of t@St @QUIDPM@NE .................lccsceseeneen en en en mm mm mm mm mm mm mm en ennennennennennenn enc 8 4& T@St R@SUI............ccceseeseenememnemnemeemeenn mm mm mm mm mm mm mm mm mm en en ennennennennennencens 9 4.A COMUUGIEU @MISSIOM ......... .cs cesc ncencencenvenvnnvnnvnne mm mm mm nc ne nc ne nc nenenne nc nennenenencncene. 9 4.2 Antenna requirement............ 4.3 Maximum peak output power .. 4.4 OUB @MISSION D&MOWIOIEA..........c. .0. 00scenencencencnncnnvnnvnnrnne mm mm mm nc ne nc nne mm mm nencned 15 4.5 Power spectral density ......... 4.6 Band edge spurious emission 4.7 Radiated emission................ Tel:{86—755)88850135 Fax: (8e—758) sessor36 hito:fii mitest.com E—mail mti@5 tmt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

EL Microtest International — Page 3 of 23 — Report No.: MTi161201E001 Test Result Certification Applicant‘s name: Microduino Inc. Address: 2659 Townsgate Rd. #213, Westlake Village, CA 91361, USA Manufacture‘s Name: Microduino Inc. Address: 2659 Townsgate Rd. #213, Westlake Village, CA 91361, USA Product name: mCookie Module BLE Upload Trademark: mCookie Model name: MCAO21, MDAO21 Standards: FCC Part 15.247 Test Procedure: ANSI C63.10—2013 * 558074 DO1 DTS Meas Guidance v03r05 This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Tested by: PMI.O( O‘M David Chen Dec. 05, 2016 Reviewed by: (guv & l’”‘y\” Leon Chen Dec. 05, 2016 Approved by: O»M /(,% ' Ares Liu Dec. 05, 2016 Tel:(86—755)88850135 Fax: (86—755) 88850136 http!/www.mtitest.com E—mail:mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bac‘an District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 4 of 23 — Report No.: MTi161201E001 Summary of Test Result Item FCC Part No. Description of Test Result 1 15.203 Antenna requirement Pass 2 15.207 grgig;\gsrlme conducted Pass 3 15.247(b)(3) Maximum peak output power Pass 4 15.247(a)(2) 6dB emission bandwidth Pass 5 15.247(e) Power spectral density (PSD) Pass 8 15.247(d) Band edge spurious emission Pass 9 15.247(d), 15.205, 15.209 Radiated emission Pass Tel:{86—755)88850135 Fax: (8e—758) sessor36 hito:fiww mitest.com E—mail mti@5 tmt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 5 of 23 — Report No.: MTi161201E001 1 General description 1.1 Feature of equipment under test (EUT) Product name: mCookie Module BLE Upload Model name: MCAO21, MDAO21 Tx/Rx frequency range: Tx/Rx: 2402MHz~2480MHz Bluetooth version: V4.0 Modulation type: GFSK Power source: DC 3.3V Antenna designation: Chip antenna (Antenna Gain: 2.5dBi) All the models above are identical in interior structure, electrical Remaric: circuits and components; just screen pattem on the PCB, ' outline and outline dimensions are different. The model MDAO21 has been tested. 1.2 Operation channel list Channel Frequency Channel Frequency Channel Frequency 0 2402MHz 10 2422MHz 20 2442MHz 1 2404MHz 11 2424MHz 21 2444MHz 8 2418MHz 18 243BMHz 38 247BMHz 9 2420MHz 19 2440MHz 39 2480MHz 1.3 Test frequency channel Low 2402MHz Middle 2442MHz High 2480MHz Telse—rss)seeso13s Fax: (86—755) seesot36 hito:fwwwmitest.com E—mail mti@5tmtl.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 6 of 23 — Report No.: MTi161201E001 1.4 EUT operation mode During testing, RF test program provided by the manufacture to control the Tx operation followed the test requirement. The EUT is configured to transmit continuously (duty cycle > 98 %) at the maximum power control level. 1.5 Test conditions During the measurement the environmental conditions were within the listed ranges: — Temperature: 20°C~30°C — Humidity: 30%~70% — Atmospheric pressure: 98kPa~101kPa 1.6 Ancillary equipment list Equipment Model Name S/N Manufacturer Certificate type Adapter T48—12—800D—2 / CUIINC FCC VOC Power Module / / mCookie FCC VOC 1.7 Measurement uncertainty Measurement Uncertainty for a Level of Confidence of 95 %, U=2xUc(y) RF frequency 1x 10—7 RF power, conducted + 1dB Conducted emission(150kHz~30MHz) £2.5 dB Radiated emission(3OMHz~1GHz) + 4.2 dB Radiated emission (above 1GHz) + 4.3 dB Temperature +1 degree Humidity £5% Tel:{86—755)88850135 Fax: (8e—758) sessor36 hito:fii mitest.com E—mail mti@5 tmt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 7 of 23 — Report No.: MTi161201E001 2 Testing site Test Site Shenzhen Toby Technology Co., Ltd. 1 A/F., Bldg.6, Yusheng Industrial Zone The National Road Test Site Location No. 107 Xixiang Section 467, Shenzhen, Guangdong, China FCC Registration No.: 811562 CNAS Registration No.: CNAS L6813 Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 8 of 23 — Report No.: MTi161201E001 3 List of test equipment For AC powerline conducted emission: Equipment Manufacturer Model Serial No. Calibration Due LISN R&S ENV216 101313 2016.12.06 LISN SCHWARZBECK NNLK 8129 8129245 2016.12.25 Pulse Limiter SCHWARZBECK VTSD 9561F 9716 2016.12.25 Test Cable N/A N/A CO1 2016.12.06 EMI Test Receiver R&S ESCI 101160 2016.12.06 For Radiated emission: Equipment Manufacturer Model Serial No. Calibration Due Log—Bicon Antenna MESSELEKTRO vure g1e0 3058 20161211 Hom Antenna Schwarzbeck BBHA 9120D 631 2016.12.05 Hom Antenna Schwarzbeck BBHA 9170 373 2016.12.05 Test Cable United Microwave 57793 im 2016.12.05 Test Cable United Microwave A30A30—5006 10m 2016.12.05 P’g’gcm’s;fir Agilent 8449B 3008A01714 2016.12.05 Pre—Amplifier Anritsu MHG48A MO9961 2016.12.05 EMI Test Receiver R&S ESPI—7 101318 2016.12.05 Spctrum analyzer Agient E4470B MY41441082 2017.06.01 For RF conducted emission: Equipment Manufacturer Model Serial No. Calibration Due EMI Test Receiver R&S ESPI—7 101318 2016.12.05 Spctrum analyzer Agient E4470B MY41441082 2017.06.01 Note: the calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (S1). Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 9 of 23 — Report No.: MTi161201E001 4 Test Result 4.1 Conducted emission 41. Limit Frequency Limit (MHz) Quasi—peak Average 0.15—0.5 66 to 56 56 to 46 0.5—5 56 46 5—30 60 50 Note: Decreases with the logarithm of the frequency from 0. 15MHz to 0.SMHz. 4.1.2 Test method 1. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through line impedance stabilization network (LISN). All other support equipment powered from additional LISN(s). The LISN provide 50 Ohm/50uH of coupling impedancefor the measuring instrument. 2. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. 3. 1/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. 4. LISN at least 80 cm from nearest part of EUT chassis. 5. The resolution bandwidth of EMI test receiver is set at 9KHz. 4.1.3 Test Result Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

L T7 Microfest International — Page 10 of 23 — Report No.: MTi161201E001 Temperature: 25°C Relative Humidity: 53% Pressure: 101kPa Polarization: L Test voltage: AC 120V/60Hz Test mode: Transmitting 100.0 dBuv 80 80 70 EN301 489 ClasiB AC Conduction{QP) 60 EN301 489 (ClassB/AC Conduction{AVB) so an 30 20 10 peak a.0 ave 0.150 a5 (Hz) 5 30.000 Reading Correct Measure— No. Mk. Freq. Level Factor ment Limit Over Nz dBuy a8 duy dBuV dB Delector Comment 1 0.1720 40.32 —0.03 40.29 64.86 —24.57 OP 2 0.1720 2415 —0.03 24.12 54.86 —30.74 AVG 3 1.3185 32.00 —0.04 31.96 56.00 —24.04 a 4* 13185 2327 —0.04 2323 4600 —22.77 AVG 5 15349 28.90 —0.04 28.86 56.00 —27.14 a 6 15349 21.47 —0.04 2143 4600 —24.57 AVG 7 2.7667 25.97 —0.04 25.93 56.00 —30.07 OP 8 2.7667 18.11 —0.04 18.07 46.00 —27.93 AVG 9 48112 24.73 —0.06 24.67 56.00 —31.33 OP 10 4.8112 18.30 —0.06 18.24 46.00 —27.76 AVG 11 10.3348 30.56 —0.09 30.47 60.00 —29.53 OP 12 10.3348 24.59 —0.09 24.50 50.00 —25.50 AVvG Tel(86—755)88850135 Fax: (86—755) 88850136 hito ffnww mtitest com E—mail. mti@5 mt.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bac‘an District, Shenzhen, Guangdong, China

L T7 Microfest International — Page 11 of 23 — Report No.: MTi161201E001 Temperature: 25C Relative Humidity: 53% Pressure: 101kPa Polarization: N Test voltage: AC 120V/60Hz Test mode: Transmitting 100.0 dBu¥ 90 70 EN301 489 ClassB AC Conduction{QP] so EN301 489 ClagsB/AC Conduction{AVG) 50 4n 30 no ue 0.150 15 tMHz] 5 20.000 Reading Correct Measure— No. Mk. Freq. Level Factor ment Limit Over Nz dBuy a8 duy dBuV dB Detector Comment 1 0.6105 37.41 —0.03 37.38 56.00 —18.62 QP 205 0.6105 29.97 —0.03 29.94 46.00 —16.06 AVG 3 1.0074 35.70 —0.04 35.66 56.00 —20.34 a 4 1.0074 29.12 —0.04 29.08 46.00 1692 AVG 5 1.3049 36.83 —0.04 36.79 56.00 —19.21 a 6 1.3049 20.82 —0.04 29.78 46.00 1622 AVG 7 16219 3234 —0.04 32.30 56.00 —23.70 QP 8 1.6219 23.07 —0.04 23.03 46.00 —22.97 AVG 9 2.6707 31.64 —0.05 31.59 56.00 —24.41 a 10 26707 24.05 —0.05 24.00 46.00 —22.00 AVG 11 3.7755 3243 —0.05 32.38 56.00 —2362 QP 12 3.7755 24.74 —0.05 24.69 46.00 —21.31 AVG Tel(86—755)88850135 Fax: (86—755) 88850136 hito (Fwww mtitest com E—mail. mti@5 1mt.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bac‘an District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 12 of 23— Report No.: MTi161201E001 4.2 Antenna requirement 4.2.1 Requirement defined in FCC 15.203 An intentional radiator shall be designed to ensure that no antenna other than that fumished by the responsible party shall be used with the device. The use of a permanently aftached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to otherintentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so thatthe limits in this part are not exceeded. 4.2.2 EUT antenna description The antenna of EUT is a permanently attached chip antenna; the maximum gain of the antenna is 2.5dBi. So the antenna meets the requirement of this part. Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 13 of 23— Report No.: MTi161201E001 4.3 Maximum peak output power 4.3.1 Limits Conducted peak output power limit is 1W (30dBm). 4.3.2 Test Method Use the following spectrum analyzer settings: RBW = 1MHz(=6dB bandwidth, see section 4.4) VBW 23RBW Detector = peak Trace mode = max hold Sweep time = auto couple Allow trace to fully stabilize. Use peak marker function to determine the peak amplitude level. 4.3.3 Test Result Frequency (MHz) Peak output power (dBm) Limit (dBm) 2402 —1.562 30 2442 —1.971 30 2480 —2.409 30 Test plots as below: Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

L Microtest International — Page 14 of 23 — Report No.: MTi161201E001 2402MHz % Aglent RoT Peak Search Heas Tools» Min Search Pk—Pk Search Hore 1 of 2 Peak Search Heas Tools» Hin Search Pk—Pk Search Hore 1 of 2 Peak Search Heas Tools» "©x"~————— AbcTo!s) et i Min Search - Pk—Pk Search Hore 1 of 2 Tel:(86—755)88850135 Fax: (86—755) 88850136 hitp tiwww mtitest com E—mail:mt@51 mti.com Address: No.102A & 3024, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bac‘an District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 15 of 23— Report No.: MTi161201E001 4.4 6dB emission bandwidth 4.4.1 Limits The minimum 6 dB bandwidth shall be at least 500 kHz. 4.4.2 Test method Use the following spectrum analyzer settings: RBW = 100KHz VBW 23RBW Detector = peak Trace mode = max hold Sweep time = auto couple Allow the trace to stabilize, measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. 4.4.3 Test result 6dB emission bandwidth Frequency (MHz) (MHz) Limit 2402 0.690 2442 0.678 500kHz 2480 0.678 Test plots as below: Tel:{86—755)88850135 Fax (se—rse) seesorse hito:fiww mitest.com E—mail mti@5 tmt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 16 of 23— Report No.: MTi161201E001 2402MHz 2442MHz 2480MHz ® 1. Telse—rss)seeso13s Fax: (86—755) seesot36 hito:fwwwmitest.com E—mail mti@5tmtl.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 17 of 23— Report No.: MTi161201E001 4.5 Power spectral density 4.5.1 Limits The power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8dBm in any 3KHz band during any time interval of continuous transmission. 4.5.2 Test method Span = 1.5 times DTS bandwidth (6dB emission bandwidth, see section 4.4) RBW = 3kHz to 100KHz VBW 23RBW Detector = peak Sweep time = auto Trace mode = max hold Allow the trace to stabilize. Use the peak marker function to determine the maximum amplitude level within the RBW. 4.5.3 Test result Frequency (MHz) PSD (dBm/100kHz) Limit (dBm/3kHz) 2402 —1.6 2442 —2.08 8 2480 —2.68 Test plots as below: Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 18 of 23— Report No.: MTi161201E001 2402MHz 2442MHz 2480MHz Telse—rss)seeso13s Fax: (86—755) seesot36 hito:fwwwmitest.com E—mail mti@5tmtl.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 19 of 23— Report No.: MTi161201E001 4.6 Band edge spurious emission 4.6.1 Limit In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. 4.6.2 Test method Use the following spectrum analyser settings: Set RBW=100 kHz. VBWzSRBW. Detector =peak, Sweep time = auto couple, Trace mode = max hold. 4.6.3 Test Result Test plots as below: Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 20 of 23 — Report No.: MTi161201E001 Band edge Low edge @ seaw roo ie veckes s imi cencer ermin on Toz ie mome base: 2.pze. z018 anszsca7 Up edge @ seaw roo ie veckes s im mac]em To en Te reome Date 2. ore. zous amsznces Tel:{86—755)88850135 Fax (se—rse) seesorse hito:fiww mitest.com E—mail mti@5 tmt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 21 of 23— Report No.: MTi161201E001 4.7 Radiated emission 4.7.1 Limit In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. Attenuation below the general limits defined in §15.209(a) is not required. in addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits defined in §15.209(a). Radiated emission limits defined in FCC 15.209: Fn(e’\c}ltir;cy FleI(:J\s/tlr:ngth Fle(deBlsjt\r;mgth Detector Me;;u;:g\:nt 30—88 100 40 oP 88—216 150 43.5 oP 216—960 200 46 oP 960—1000 500 46 oP om Above 1000 500 54 AV Above 1000 5000 74 PK Restricted bands defined in FCC 15.205: MHz MHz MHz GHz 0.090—0.110 16.42—16.423 309.9—410 4.5—5.15 0.495—0.505 16.69475—16.69525 608—614 5.35—5.46 2.1735—2.1905 16.80425—16.80475 960—1240 7.25—7.75 4.125—4.128 25.5—25.67 1300—1427 8.025—8.5 4.17725—4.17775 37.5—38.25 1435—1626.5 9.0—9.2 4.20725—4.20775 73—74.6 1645.5—1646.5 9.3—9.5 6.215—6.218 74.8—75.2 1660—1710 10.6—12.7 6.26775—6.26825 108—121.94 1718.8—1722.2 13.25—13.4 6.31175—6.31225 123138 2200—2300 14.47—14.5 8.291—8.294 149.9—150.05 2310—2390 15.35—16.2 8.362—8.366 156.52475—156.52525 2483.5—2500 17.7—21.4 8.37625—8.38675 156.7—156.9 2690—2900 22.01—23.12 8.41425—8.41475 162.0125—167.17 3260—3267 23.6—24.0 12.29—12.293 167.72—173.2 3332—3330 31.2—31.8 12.51975—12.52025 240—285 3345.8—3358 36.43—36.5 12.57675—12.57725 322—335.4 3600—4400 Above 38.6 13.36—13.41 Tel:{86—755)88850135 Fax (se—rse) seasorse hito:fiww mitest.com E—mail mti@5 tmt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 22 of 23— Report No.: MTi161201E001 4.7.2 Test method 1. The EUT is placed on a tumtable, which is 0.8m above ground plane for test frequency range blew 1GHz, and 1.5m above ground plane for test frequency range above 1GHz. 2. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 3. Use the following spectrum analyzer settings: Span = wide enough to fully capture the emission being measured, RBW = 1 MHz forf 2 1GHz, 100 KHz for f < 1 GHz, VBW z RBW, Sweep = auto, Detector function = peak, Trace = max hold 4. Follow the guidelines in ANSI C63.4—2014 with respect to maximizing the emission by rotating the EUT, adjusting the measurement antenna height and polarization, etc. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre—amp gain, etc., is the peak field strength, submit this data. Each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 5. The peak level, once corrected, must comply with the limit specified in Section 15.209. Set the RBW = 1MHz, VBW = 3MHz, Detector = RMS for AV value, while maintaining all of the other instrument settings. 6. The three orthogonal axis (x, y, z) are pre—tested, only the worst emission were reported 4.7.3 Test Result Remark: If the PK measured values lower than average mode limit, the EUT shall be deemed to meet average limits and then no additional average mode measurement performed. Telse—rss)sseso13s Fax: (se—rse) seasorse hito:fwwwniitest.com E—mail mti@5mt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China

i Microfest Infernational — Page 23 of 23— Report No.: MTi161201E001 Transmitter channel: 2402MHz Frequency A_nt. . Emission level Limits Polarization Detector| Result (MHz) H/V dBuVim dBuV/im 139.85 V 23.5 43.5 QP 139.85 H 30.4 43.5 aP 2390 V 46.48 74 PK Pass 2390 H 47.12 74 PK 4804 V 49.39 74 PK 4804 H 48.46 74 PK Transmitter channel: 2442MHz Ant. feas m Frequency Polarization Emission level Limits Detector| Result (MHz) H/V dBuVim dBuVim 139.85 V 22.3 43.5 aP 139.85 H 29.7 43.5 aP Pass 4884 V 49.26 74 PK 4884 H 48.49 74 PK Transmitter channel: 2480MHz Frequency PoIaArir;tétion Emission level Limits Detector (MHz) H/V dBuVim dBuVim 139.85 V 23.2 43.5 aP 139.85 H 30.3 43.5 QP__| Result 2483.5 V 47.24 74 PK 2483.5 H 46.39 74 PK 4960 V 50.19 74 PK 4960 H 49.31 74 PK ——END OF REPORT———— Tel:{86—755)88850135 Fax: (8e—758) sessor36 hito:fii mitest.com E—mail mti@5 tmt.com Address: No.102A & 302A, East Block, Hengfang Industria! Park, Xingye Road, Xixang, Bacan District, Shenzhen, Guangdong, China


Document Created: 2017-01-05 14:04:56
Document Modified: 2017-01-05 14:04:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC