Test Report

FCC ID: 2AKLPA7

Test Report

Download: PDF
FCCID_3663173

S FCC Part 15B TEST REPORT T Report No: STS1710261E01 S Issued for TOOCAN ELECTRONICS S.A.S Calle 45 # 53-50 oficina 0911 CC gran plaza, medellin, Colombia L Product Name: Brand Name: Smart phone Blackview A Model Name: Series Model: A7 N/A B FCC ID: Test Standard: 2AKLPA7 FCC Part 15B Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from STS, All Test Data Presented in this report is only applicable to presented Test sample. Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong, China TEL: +86-755 3688 6288 FAX: +86-755 3688 6277 E-mail:sts@stsapp.com

Page 2 of 21 Report No.: STS1710261E01 TEST RESULT CERTIFICATION Applicant’s name ..................: TOOCAN ELECTRONICS S.A.S Address ..................................: Calle 45 # 53-50 oficina 0911 CC gran plaza, medellin, Colombia Manufacture's Name ............: JIEKE TECHNOLOGY (HK) LIMITED 13th Floor, Weidonglong commercial building B, Meilong avenue, Address ..................................: Longhua New District, Shenzhen, China. Product description Product name .........................: Smart phone Brand name............................: Blackview Model Name .........................: A7 Series Model ........................ N/A Standards..............................: FCC Part 15B Test procedure ...........................ANSI : C63.4-2014 This device described above has been tested by STS, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of STS, this document may be altered or revised by STS, personal only, and shall be noted in the revision of the document. Date of Test .......................................... : Date of performance of tests ................ 31 Oct.: 2017~21 Nov. 2017 Date of Issue ........................................ 22 Nov.: 2017 Test Result ........................................... Pass : Testing Engineer : ( Kyle Rao ) Technical Manager : ( Chopin Xiao ) Authorized Signatory : ( Vita Li )

Page 3 of 21 Report No.: STS1710261E01 Table of Contents 1. SUMMARY OF TEST RESULTS 5 1.1 TEST FACTORY 5 1.2 MEASUREMENT UNCERTAINTY 5 2. GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 8 2.4 DESCRIPTION OF SUPPORT UNITS 9 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 10 3. EMC EMISSION TEST 11 3.1 CONDUCTED EMISSION MEASUREMENT 11 3.2 RADIATED EMISSION MEASUREMENT 15

Page 4 of 21 Report No.: STS1710261E01 Revision History Rev. Issue Date Report NO. Effect Page Contents 00 22 Nov. 2017 STS1710261E01 ALL Initial Issue

Page 5 of 21 Report No.: STS1710261E01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: EMISSION Standard Item Result Remarks FCC 47 CFR Part 15 Subpart B Conducted Emission PASS Meet Class B limit (10-1-05 Edition) Radiated Emission PASS Meet Class B limit NOTE: (1) ” N/A” denotes test is not applicable in this Test Report 1.1 TEST FACTORY Company Name: Shenzhen STS Test Services Co. Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Address: Fuyong Street, Bao’an District, Shenzhen, Guangdong, China Telephone: +86-755 3688 6288 Fax: +86-755 3688 6277 CNAS Registration No.: L7649; FCC Registration No.: 625569 Registration No.: IC Registration No.: 12108A; A2LA Certificate No.: 4338.01; 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission (9KHz-150KHz) ±2.88dB 2 Conducted Emission (150KHz-30MHz) ±2.67dB 3 All emissions,radiated(<30M) (9KHz-30MHz) ±2.45dB 4 All emissions,radiated(<1G) 30MHz-200MHz ±3.80dB 5 All emissions,radiated(<1G) 200MHz-1000MHz ±3.97dB 6 All emissions,radiated(>1G) ±3.03dB

Page 6 of 21 Report No.: STS1710261E01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product Name Smart phone Brand Name Blackview Model Name A7 Series Model N/A Model Difference N/A 850: 824.2~848.8MHz GSM 1900: 1850.2~1909.8MHz Band II: 1852.4~1907.6MHz WCDMA Band V: 826.4~846.6MHz Frequency Bands WLAN 802.11b/g/n(HT20/40):2412~2462MHz Bluetooth 2402~2480MHz GSM GMSK for GPRS; GMSK and 8PSK for EDGE WCDMA QPSK; HSDPA:QPSK/16QAM; HSUPA:BPSK WLAN CCK/OFDM/DBPSK/DAPSK Modulation Mode GFSK(1Mbps), π/4-DQPSK(2Mbps), Bluetooth 8DPSK(3Mbps) BLE GFSK Input: AC100-240V, 0.2A, 50/60Hz Adapter Output: DC 5V,1000mA Rated Voltage: 3.8V Battery Capacity: 2800mAh Charge Limit: 4.35V Hardware version number HCT-W178MB-A2 Software version number A7- Blackview-V0.1 Note: For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual.

Page 7 of 21 Report No.: STS1710261E01 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 USB port communication with PC For Conducted Test Final Test Mode Description Mode 1 USB port communication with PC For Radiated Test Final Test Mode Description Mode 1 USB port communication with PC NOTE: 1. The test modes were carried out for all operation modes. Only worst case will be show in this report. 2. We have be tested for all avaiable U.S. voltage and frequencies(For 120V, 50/60Hz) for which the device is capable of operation.

Page 8 of 21 Report No.: STS1710261E01 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED E-4 Printer E-2 Keyboard C-4 C-2 C-1 AC E-1 Plug EUT PC C-3 E-3 Mouse

Page 9 of 21 Report No.: STS1710261E01 2.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Note Auxiliary E-1 PC 4CV428DQXR 500-320cx equipment Auxiliary E-2 Keyboard HP PR1101U equipment Auxiliary E-3 Mouse MOTOSPEED F66 equipment Auxiliary E-4 Printer HP HP1020 equipment Item Shielded Type Ferrite Core Length Note USB Cable Auxiliary C-1 NO 95cm (FTP) equipment USB Cable Auxiliary C-2 NO 110cm (FTP) equipment USB Cable Auxiliary C-3 NO 115cm (FTP) equipment USB Cable Auxiliary C-4 NO 120cm (FTP) equipment Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column. (3) “YES” is means “shielded” “with core”; “NO” is means “unshielded” “without core”. (4) PC is the FCC DOC is approved.

Page 10 of 21 Report No.: STS1710261E01 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Radiation Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last Calibration Calibrated Until EMI Test Receiver R&S ESCI 101427 2017.10.15 2018.10.14 Bilog Antenna TESEQ CBL6111D 34678 2017.03.24 2018.03.23 SCHWARZBE BBHA Horn Antenna 9120D-1343 2017.03.06 2018.03.05 CK 9120D(1201) Power Amplifier Agilent 8449B 60538 2017.10.15 2018.10.14 Spectrum Analyzer Agilent E4407B MY50140340 2017.03.11 2018.03.10 Pre-mplifier(0.1M-3 EM EM330 60538 2017.03.12 2018.03.11 GHz) Spectrum Analyzer Agilent N9020A MY49100060 2017.03.11 2018.03.10 EMI Test Receiver ESW R&S 101535 2017.06.01 2018.05.31 Conduction Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last Calibration Calibrated Until EMI Test Receiver R&S ESPI 102086 2017.10.15 2018.10.14 LISN R&S ENV216 101242 2017.10.15 2018.10.14 LISN EMCO 3810/2NM 000-23625 2017.10.15 2018.10.14 Absorbing clamp R&S MDS-21 100668 2017.10.20 2018.10.19

Page 11 of 21 Report No.: STS1710261E01 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION Limits Conducted Emission Limits (dBuV) FREQUENCY (MHz) Class A Class B Quasi-peak Average Quasi-peak Average 0.15 -0.5 79.00 66.00 66 - 56 * 56 - 46 * 0.50 -5.0 73.00 60.00 56.00 46.00 5.0 -30.0 73.00 60.00 60.00 50.00 Note: (1) The tighter limit applies at the band edges. The limit of " * " marked band means the limitation decreases linearly with the (2) logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 12 of 21 Report No.: STS1710261E01 3.1.2 TEST PROCEDURE The EUT was 0.8 meters from the horizontal ground plane and 0.4 meters from the vertical ground plane with EUT being connected to the power mains through a line impedance a. stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back b. and forth in the center forming a bundle 30 to 40 cm long. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the c. cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.1.3 DEVIATION FROM TEST STANDARD No deviation 3.1.4 TEST SETUP Vertical Reference Ground Plane Test Receiver EUT 40cm 80cm LISN Horizontal Reference Ground Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 3.1.5 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

Page 13 of 21 Report No.: STS1710261E01 3.1.6 TEST RESULTS Temperature: 26.5 °CC Relative Humidity: (68% Pressure: 1010hPa Phase: L Test Voltage: AC 120V/60Hz Test Mode: Mode 1 Frequency Reading Factor Result Limit Margin No. (MH2) (dBuy) (dB) (dBuV) (dBuv) (dB) Detector 1 0.1540 47.50 9.79 57.29 65.78 —8.49 aP 2 0.1540 30.10 9.79 39.89 55.78 —15.89 AVG 3 0.4860 30.05 10.03 40.08 56.24 1616 aP 4 0.4860 19.60 10.03 29.63 46.24 —16.61 AVG 5 1.1820 29.39 9.80 39.19 56.00 —16.81 aP 6 1.1820 19.28 9.80 29.08 46.00 —16.92 AVG 7 1.7340 34.71 9.79 44.50 56.00 —11.50 aP 8 1.7340 22.41 9.79 32.20 46.00 —13.80 AVG 9 6.4620 30.38 9.87 40.25 60.00 —19.75 aP 10 6.4620 15.29 9.87 25.16 50.00 —24.84 AVG 11 15.2900 26.58 10.25 36.83 60.00 —23.17 aP 12 15.2900 13.81 10.25 24.06 50.00 —25.94 AVG Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 100.0 dBu¥ Limit1: — Limit2: — \ 50 &\ ——————— peak AVG 0.0 0.150 (MHz] 30.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Fax+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

NA \/ Page 14 of 21 Report No.: STS1710261E01 Temperature: 26.5 °CC Relative Humidity: (68% Pressure: 1010hPa Phase: N Test Voltage: AC 120V/60Hz Test Mode: Mode 1 Frequency Reading Factor Result Limit Margin No. (MH2) (dBuy) (dB) (dBuV) (dBuv) (dB) Detector 1 0.1580 47.01 9.77 56.78 65.57 —8.79 aP 2 0.1580 34.36 9.77 44.13 55.57 —11.44 AVG 3 0.4340 32.07 10.03 42.10 57.18 —15.08 aP 4 0.4340 22.20 10.03 32.23 47.18 —14.95 AVG 5 1.7340 35.72 9.85 45.57 56.00 —10.43 aP 6 1.7340 24.99 9.85 34.84 46.00 —11.16 AVG 7 3.0860 31.61 9.91 41.52 56.00 —14.48 aP 8 3.0860 22.78 9.91 32.69 46.00 —13.31 AVG 9 5.4260 31.95 9.91 41.86 60.00 —18.14 QP 10 5.4260 21.84 9.91 31.75 50.00 —18.25 AVG 11 15.1540 28.95 10.09 39.04 60.00 —20.96 QaP 12 15.1540 15.70 10.09 25.79 50.00 —24.21 AVG Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 100.0 dBu¥ Limit1: — Limit2: — \ 50 I— peak AVG 0.0 0.150 0.5 (MHz] 5 30.000 Note: The test voltage is 100—240V, both of which have assessment tests, and the worst test data is in the report. 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Fax+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

Page 15 of 21 Report No.: STS1710261E01 3.2 RADIATED EMISSION MEASUREMENT 3.2.1 Radiated Emission Limits In case the emission fall within the restricted band specified on 15.105(a)&109(a) limit in the table below has to be followed. Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 LIMITS OF RADIATED EMISSION MEASUREMENT Class A (dBuV/m) (at 3M) Class B (dBuV/m) (at 3M) FREQUENCY (MHz) PEAK AVERAGE PEAK AVERAGE Above 1000 80 60 74 54 Note: (1) The limit for radiated test was performed according to FCC PART 15B. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20log Emission level (uV/m). FREQUENCY RANGE OF RADIATED MEASUREMENT (For unintentional radiators) Highest frequency generated or Upper frequency of measurement used in the device Range (MHz) or on which the device operates or tunes (MHz) Below 1.705 30 1.705 – 108 1000 108 – 500 2000 500 – 1000 5000 5th harmonic of the highest frequency or 40 GHz, Above 1000 whichever is lower

Page 16 of 21 Report No.: STS1710261E01 Spectrum Parameter Setting Attenuation Auto Detector Peak Start Frequency 1000 MHz(Peak/AV) Stop Frequency 5th harmonic (Peak/AV) 30MHz to 1000MHz: 100 KHz / 300 KHz RB / VB (emission in restricted band) Above 1000MHz: 1 MHz / 3 MHz Receiver Parameter Setting Attenuation Auto 30MHz to 1000MHz: 100 KHz / 300 KHz Start ~ Stop Frequency Above 1000MHz: 1 MHz / 3 MHz 3.2.2 TEST PROCEDURE The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz a. and above 1GHz. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter b. anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. the height of the antenna shall vary between 1m to 4 m. Both horizontal and vertical c. polarizations of the antenna are set to make the measurement. The initial step in collecting conducted emission data is a spectrum analyzer peak detector d. mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the e. EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. f. For the actual test configuration, please refer to the related Item –EUT Test Photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported 3.2.3 DEVIATION FROM TEST STANDARD No deviation

D 4 \/ Page 17 of 21 Report No.: STS1710261E01 3.2.4 TEST SETUP (A) Radiated Emission Test—Up Frequency 3OMHz~1GHz Turntable s ”””” \ (Eut Spectrum IU.Sm Analyzer Ground Plane :I Coaxial Cable EUTi«—— 3m Amplifier 0.8m ... t ze Turntable Spectrum Analyzer oun: Pla ne Ground Coaxial Cable 3.2.5 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. JL Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E~mail: sts@stsapp.com

t o# Page 18 of 21 enredoettectcd 3.2.6 TEST RESULTS 30MHz —1000MHz Temperature: 24.6°C Relative Humidity: (59% Pressure: 1010hPa Phase: Horizontal Test Voltage: AC 120V/60Hz Test Mode: Mode 1 Frequency Reading Results Limit Margin No. (MHz) (dBuV) Factor (dB) (dBuVv/m) (dBuV/m) (dB) Detector 1 79.8003 52.42 —22.72 29.70 40.00 —10.30 aP 2 134.0882 51.30 —17.54 33.76 43.50 —9.74 aP 3 187.7530 54.52 —20.07 34.45 43.50 —9.05 QaP 4 215.2678 54.11 —19.41 34.70 43.50 —8.80 aP 5 237.1360 62.52 —17.96 44.56 46.00 —1.44 aP 6 962.1622 37.16 —0.12 37.04 54.00 —16.96 aP Remark: 1. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: —— Margin: — -l[l—l—I j 1 0.0 30.000 40 50 Go 70 80 (MHz) 300 400 500 600 700 1000.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

t J Page 19 of 21 Report No.: STS1710261E01 Temperature: 24.6 °C Relative Humidity: (59% Pressure: 1010hPa Phase: Vertical Test Voltage: AC 120V/60Hz Test Mode: Mode 1 Frequency Reading Results Limit Margin No. (MHz) (dBuV) Factor (dB) (dBuV/m) (dBuV/m) (dB) Detector 1 55.6094 46.12 —23.08 23.04 40.00 —16.96 aP 2 90.2205 43.23 —20.18 23.05 43.50 —20.45 aP 3 134.0882 45.94 —17.54 28.40 43.50 —15.10 aP 4 237.4760 54.16 —17.94 36.22 46.00 —9.78 aP 5 475.4991 39.82 —9.57 30.25 46.00 —15.75 aP 6 625.0780 43.40 —6.43 36.97 46.00 —9.03 QaP Remark: 1. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: — a0 —l—l—l 1 & 5 3 j 1 2 0.0 30.000 40 50 60 70 80 (MHz] 300 400 500 600 700 1000.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

t o# Page 20 of 21 enredoettectcd (1 GHz to 25GHz.) Temperature: 26 °C Relative Humidity: 154% Pressure: 1010hPa Phase: Vertical/Horizontal Test Voltage: AC 120V/60Hz Test Mode: Mode 1 PK Freq. Ant. Pol Peak Amplifier Loss Antenna Orrected Actual Fs Peak Peak Factor Factor (MHz) HAV s (dB) (dB) (dB/m) (dB) Peak Limit es (dBuV) (dBuV/m) (dBuV/im) (dB) 2005.32 H 56.25 43.81 5.42 25.93 —12.54 43.79 74.00 —30.21 2508.61 H 50.24 44.47 6.11 27.64 —10.81 39.52 74.00 —34.48 3000.42 H 52.56 44.78 6.73 28.22 —9.82 42.73 74.00 —31.27 4400.87 H 54.44 44.35 8.42 30.44 —5.48 48.95 74.00 —25.05 2005.34 V 51.24 43.84 5.48 25.95 —12.54 38.83 74.00 —35.17 2508.61 V 49.65 44.48 6.23 27.69 —10.83 39.09 74.00 —34.91 3000.43 V 50.58 44.75 6.76 28.26 —9.85 40.85 74.00 —33.15 4400.86 V 48.52 44.34 8.42 30.45 —5.48 43.05 74.00 —30.95 5506.84 V 37.12 44.21 9.77 32.23 —2.59 34.91 74.00 —39.09 AV Freq. Ant. Pol AV Amplifier Loss Antenna Orrected AV AV Factor Factor (MHz) HA s (dB) (dB) (dB/m) (dB) AV Limit es (dBuV) (dBuV/m) (dBuV/im) (dB) 1403.35 H 46.32 45.13 4.24 25.11 4.24 30.54 54.00 —23.46 3000.76 H 48.24 44.78 6.71 28.26 —9.80 38.43 54.00 —15.57 4002.47 H 52.65 44.25 7.93 29.74 —6.60 46.07 54.00 —7.93 5506.84 H 44.15 44.23 9.71 32.32 —2.50 41.95 54.00 —12.05 N/A 1403.35 V 37.45 45.14 4.29 25.15 —16.00 21.75 54.00 —32.25 3000.76 V 41.63 44.75 6.75 28.26 —9.80 31.89 54.00 —22.11 4002.47 V 36.42 44.24 7.96 29.74 —6.60 29.88 54.00 —24.12 5506.84 V 38.24 44.26 9.72 32.35 —2.50 36.05 54.00 —17.95 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Torrsecres soee none: necrse—res ces narr. Miheiimnnstsenscom E—maicsic@stsepcition

Page 21 of 21 Report No.: STS1710261E01 Notes: 1. Measuring frequencies from 1 GHz to 25GHz. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using Peak detector mode of the emission shown in Actual FS column. 3. The frequency that above 5.5GHz is mainly from the environment noise. ※※※※※END OF THE REPORT※※※※※


Document Created: 2017-11-27 09:18:24
Document Modified: 2017-11-27 09:18:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC