Users Manual

FCC ID: 2AKIT-AK024

Users Manual

Download: PDF
FCCID_4240611

Smart Wall Switch Before you install 2. Remove the existing switch and identify the wires with wire labels. 5. Install the wall plate, turn main power ON at the circuit breaker, and test the switch by pressing the button; (With Neutral, Single Rocker) This product is only used to replace a single pole switch rather than a If it doesn’t work, please check: a. If the wiring is correct; b. If the power 3-way switch. Ground Usually green/bare. is restored. Product Profile If it works, add the switch to the app following the next steps; Neutral Usually white. Quick Setup 1. Please add the Hub to the app according to the Hub Quick Start Guide. Line(Hot)/Load 2. Please open the app, and then tap “+” in the top right corner to enter Required, usually black, and always present. “Add Device (Accessory)” page. Select “Smart Wall Switch (With Neutral, Single Rocker)”, and add it according to instructions. Push Button *If the connection fails, please move the hub closer to the switch, connect to Short Press Once: Turn on/off power and try again. 3. Install the smart wall switch and connect the wires as required. Long Press for 5s: Reconnect Quick Press 3 Times: Effective Range Test Effective Range Test: Quick press the button on the device 3 times. If Double click and long press 5s: Reset the Hub makes voice prompts, it indicates that the device can Ground Usually green/bare. communicate effectively with the Hub. Installation Neutral Indicator Light Visit www.aqara.com/support for more information. Required, usually white. Indicator Light Description 1. Turn off power at circuit breaker or fuse box and test that power is off Indicator Light Status Status Description before wiring. (Please switch the light several times to make sure that Line(Hot)/Load Blue light blinks quickly Zigbee network is connecting the power has been disconnected) Required, usually black, and always present. Blue light keeps on Zigbee network works properly Red light blinks quickly Overload and high temperature alarm * This product requires a compatible hub. Some features require a specific hub. Red light blinks slowly Zigbee network is not connected For the detailed list, please visit: www.aqara.com/support 4. Tuck the wires into the wall box leaving room for the smart switch. Using the screws provided, mount the smart switch to the wall box. Be OFF ON OFF ON careful not to crush any wires. (Note: avoid overtightening the screws.) Warning OFF ON OFF ON Specification 1. A certain amount of electrical knowledge is required to install a smart Model: QBKG15LM Smart Wall Switch wall switch. For your safety, we recommend that you ask a qualified OFF ON OFF ON Dimensions: 120 x 74 x 36.5 mm (4.72 x 2.91 x 1.44 in) Manufacturer: Lumi United Technology Co., Ltd. OFF OFF ON (With Neutral, Single Rocker) electrician to help you install it; 2. This product is for indoor use only; do not use it in humid environment; Wireless Protocol: Zigbee3.0 Address: 8th Floor, JinQi Wisdom Valley, OFF OFF ON Input: 120 V AC 60 Hz No.1 Tangling Road, Liuxian Ave, Taoyuan 3. Do not install this product near a heat source; Max Load: 1200 W (Incandescent), 200 W (CFL/LED), 1/4 HP Residential District, Nanshan District, 4. IMPORTANT!: This Smart Switch is rated for and intended to only Operating Temperature: 0 – 40° C（32 – 104° F） Shenzhen, China. be used with copper wire. Operating Humidity: 0 – 95% RH, non-condensing Online Customer Service: www.aqara.com/support Zigbee 3.0 Email: support@aqara.com Install Code Switch de pared inteligente Antes de la instalación 2. Retire el switch que se vaya a sustituir y marque el cable con la etiqueta 5. Coloque la cubierta de superficie del switch, conecte la alimentación y Fabricante: Lumi United Technology Co., Ltd. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of de cables para identificar el cable correspondiente en la instalación. controle con el botón; si el control no funciona, compruebe que las Dirección: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian (con neutro, basculante simple) Verifique la compatibilidad 20 cm between the radiator and your body. This transmitter must not be co-located or conexiones sean correctas y que se haya conectado la alimentación; Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. Este producto solo puede sustituir switch de control sencillo en lugar de operating in conjunction with any other antenna or transmitter. si funciona, siga los pasos a continuación para agregar el producto. Servicio de atención al cliente en línea: www.aqara.com/support Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils switches de doble control. Tierra Perfil del producto Normalmente de color verde. Correo electrónico: support@aqara.com radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter Neutro Configuración rápida tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en FCC ID: 2AKIT-AK024 compromettre le fonctionnement. Generalmente blanco. 1. Agregue el hub a la aplicación de acuerdo con la Guía rápida del hub. Federal Communications Commission (FCC) compliance statement Cet équipement est conforme aux limites IC d'exposition aux radiations définies pour un 2. Abra la aplicación, pulse «+» en la parte superior derecha para 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance two conditions: acceder a la página «Add Device (Accessory)» (Agregar dispositivo minimale de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être situé (1) This device may not cause harmful interference. Línea/Carga [accesorio]). Seleccione Switch de pared inteligente (con neutro, ou opérant en conjonction avec une autre antenne ou émetteur. (2) This device must accept any interference received, including interference that may Obligatorio, normalmente de color negro, basculante simple) y siga las instrucciones para agregarlo. cause undesired operation. Botón siempre presente. *Si falla la conexión, acerque el switch de pared al hub, conéctelo y vuelva a 2. Changes or modifications not expressly approved by the party responsible for Pulsación corta: encender/apagar intentarlo. compliance could void the user's authority to operate the equipment. Pulsación larga durante cinco 3. Instale el switch de pared inteligente y conecte el cable según sea segundos: volver a conectar Prueba de alcance efectivo: pulse rápidamente tres veces el botón en el NOTE: This equipment has been tested and found to comply with the limits for a Class B necesario; digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide Tres pulsaciones rápidas: accesorio. Si el hub emite un mensaje de voz, significa que el accesorio prueba de alcance efectivo reasonable protection against harmful interference in a residential installation. y el sensor se están comunicando correctamente. This equipment generates uses and can radiate radio frequency energy and, if not installed Haga doble clic y mantenga durante Tierra cinco segundos: Restablecimiento de fábrica Normalmente de color verde. and used in accordance with the instructions, may cause harmful interference to radio communications. Luz indicadora Installation Descripción de la luz indicadora However, there is no guarantee that interference will not occur in a particular installation. If Neutro this equipment does cause harmful interference to radio or television reception, which can Visitar en www.aqara.com/support para obtener más información. Generalmente blanco. Estado de la luz indicadora Descripción del estado be determined by turning the equipment off and on, the user is encouraged to try to correct 1. Desconecte la alimentación del switch que se vaya a sustituir antes de the interference by one or more of the following measures: La luz azul parpadea rápidamente Se está estableciendo conexión con la la instalación (apague y encienda la luz varias veces para comprobar red Zigbee - Reorient or relocate the receiving antenna. Línea/Carga - Increase the separation between the equipment and receiver. que se ha desconectado la alimentación). Obligatorio, normalmente de color Luz azul fija La red Zigbee funciona correctamente - Connect the equipment into an outlet on a circuit different from that to which the receiver negro, siempre presente. is connected. La luz roja parpadea rápidamente Alarma de sobrecarga y temperatura alta - Consult the dealer or an experienced radio/TV technician for help. * Este producto debe utilizarse con un dispositivo con funcionalidad de puerta de FCC Radiation Exposure Statement enlace. Algunas funciones requieren compatibilidad con modelos de puerta de La luz roja parpadea lentamente No hay conexión con la red Zigbee enlace específicos. Para una lista detallada, visite: www.aqara.com/support 4. Extraiga la cubierta de superficie y fije el switch a la caja de interruptores This equipment complies with FCC radiation exposure limits set forth for an uncontrolled OFF ON OFF ON con tornillos. (Nota: no apriete demasiado los tornillos para no deformar environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. el switch) OFF ON OFF ON Advertencia Especificaciones OFF ON OFF ON IC: 22635-AK024 1. La instalación de un switch inteligente requiere ciertos conocimientos Modelo: QBKG15LM IC NOTICE TO CANADIAN USERS OFF OFF ON en materia de electricidad. Para su seguridad personal, se recomienda Dimensiones: 120 x 74 x 36,5 mm（4,72 x 2,91 x 1,44 pulgadas) This device complies with Industry Canada license‐exempt RSS standard(s). Operation is pedir ayuda a un electricista cualificado para la instalación. OFF OFF ON Protocolo inalámbrico: Zigbee3.0 subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired 2. Este producto ha sido diseñado exclusivamente para uso en Entrada: 120 VCA, 60 Hz operation of the device. This device complies with RSS‐247 of Industry Canada. interiores; no lo utilice en un entorno húmedo. Cargas máximas: 1200W (incandescente), 200W (CFL/LED), 1/4HP (total) Operation is subject to the condition that this device does not cause harmful interference. 3. No instale el producto cerca de una fuente de calor. Temperatura de funcionamiento: 0 – 40° C（32 – 104° F） This Class B digital apparatus complies with Canadian ICES‐003 (Cet appareil numérique Humedad de funcionamiento: 0 – 95% HR, sin condensación de la Classe B conforme à la norme NMB‐003 du Canada). 美标墙壁开关（零火单键）说明书 料号：3020319 材质：金东太空梭105G无光铜纸

438mm 73mm 正折 反折 正折 反折 正折 Smart Wall Switch Before you install 2. Remove the existing switch and identify the wires with wire labels. 5. Install the wall plate, turn main power ON at the circuit breaker, and test the switch by pressing the button; (With Neutral, Double Rocker) This product is only used to replace a single pole switch rather than a If it doesn’t work, please check: a. If the wiring is correct; b. If the power 3-way switch. Ground Usually green/bare. is restored. Product Profile If it works, add the switch to the app following the next steps; Neutral Usually white. Quick Setup 1. Please add the Hub to the app according to the Hub Quick Start Guide. Line(Hot)/Load 2. Please open the app, and then tap “+” in the top right corner to enter Required, usually black, and always present. “Add Device (Accessory)” page. Select “Smart Wall Switch (With Neutral, Double Rocker)”, and add it according to instructions. Push Button *If the connection fails, please move the hub closer to the switch, connect to Short Press Once: Turn on/off 3. Install the smart wall switch and connect wires as required. power and try again. Long Press for 5s: Reconnect Effective Range Test: Quick press the button on the device 3 times. If Quick Press 3 Times: Effective Range Test Double click and long press 5s: Reset the Hub makes voice prompts, it indicates that the device can Ground Usually green/bare. communicate effectively with the Hub. Installation 118mm Neutral Indicator Light Visit www.aqara.com/support for more information. Required, usually white. Indicator Light Description 1. Turn off power at circuit breaker or fuse box and test that power is off Indicator Light Status Status Description before wiring. (Please switch the light several times to make sure that Line(Hot)/Load Blue light blinks quickly Zigbee network is connecting the power has been disconnected) Required, usually black, and always present. Blue light keeps on Zigbee network works properly Red light blinks quickly Overload and high temperature alarm * This product requires a compatible hub. Some features require a specific hub. Red light blinks slowly Zigbee network is not connected For the detailed list, please visit: www.aqara.com/support 4. Tuck the wires into the wall box leaving room for the smart switch. Using the screws provided, mount the smart switch to the wall box. Be OFF ON OFF ON careful not to crush any wires. (Note: avoid overtightening the screws.) Warning OFF ON OFF ON Specification 1. A certain amount of electrical knowledge is required to install a smart Model: QBKG16LM Smart Wall Switch wall switch. For your safety, we recommend that you ask a qualified OFF ON OFF ON Dimensions: 120 x 74 x 36.5 mm (4.72 x 2.91 x 1.44 in) Manufacturer: Lumi United Technology Co., Ltd. OFF OFF ON (With Neutral, Double Rocker) electrician to help you install it; 2. This product is for indoor use only; do not use it in humid environment; Wireless Protocol: Zigbee3.0 Address: 8th Floor, JinQi Wisdom Valley, OFF OFF ON Input: 120 V AC 60 Hz No.1 Tangling Road, Liuxian Ave, Taoyuan 3. Do not install this product near a heat source; Max Load: 1200 W (Total, Incandescent), 200 W/way (CFL/LED), 1/4 HP Residential District, Nanshan District, 4. IMPORTANT!: This Smart Switch is rated for and intended to only Operating Temperature: 0 – 40° C（32 – 104° F） Shenzhen, China. be used with copper wire. Operating Humidity: 0 – 95% RH, non-condensing Online Customer Service: www.aqara.com/support Zigbee 3.0 Email: support@aqara.com Install Code 反折 正折 反折 正折 反折 Switch de pared inteligente Antes de la instalación 2. Retire el switch que se vaya a sustituir y marque el cable con la etiqueta 5. Coloque la cubierta de superficie del switch, conecte la alimentación y Fabricante: Lumi United Technology Co., Ltd. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of de cables para identificar el cable correspondiente en la instalación. controle con el botón; si el control no funciona, compruebe que las Dirección: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian (con neutro, basculante doble) Verifique la compatibilidad 20 cm between the radiator and your body. This transmitter must not be co-located or conexiones sean correctas y que se haya conectado la alimentación; Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. Este producto solo puede sustituir switch de control sencillo en lugar de operating in conjunction with any other antenna or transmitter. si funciona, siga los pasos a continuación para agregar el producto. Servicio de atención al cliente en línea: www.aqara.com/support Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils switches de doble control. Tierra Perfil del producto Normalmente de color verde. Correo electrónico: support@aqara.com radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter Neutro Configuración rápida tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en FCC ID: 2AKIT-AK024 compromettre le fonctionnement. Generalmente blanco. 1. Agregue el hub a la aplicación de acuerdo con la Guía rápida del hub. Federal Communications Commission (FCC) compliance statement Cet équipement est conforme aux limites IC d'exposition aux radiations définies pour un 2. Abra la aplicación, pulse «+» en la parte superior derecha para 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance two conditions: acceder a la página «Add Device (Accessory)» (Agregar dispositivo minimale de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être situé (1) This device may not cause harmful interference. Línea/Carga [accesorio]). Seleccione Switch de pared inteligente (con neutro, ou opérant en conjonction avec une autre antenne ou émetteur. (2) This device must accept any interference received, including interference that may Obligatorio, normalmente de color negro, Botón basculante doble) y siga las instrucciones para agregarlo. cause undesired operation. siempre presente. Pulsación corta: encender/apagar *Si falla la conexión, acerque el switch de pared al hub, conéctelo y vuelva a 2. Changes or modifications not expressly approved by the party responsible for Pulsación larga durante cinco intentarlo. compliance could void the user's authority to operate the equipment. segundos: volver a conectar 3. Instale el switch de pared inteligente y conecte el cable según sea NOTE: This equipment has been tested and found to comply with the limits for a Class B Prueba de alcance efectivo: pulse rápidamente tres veces el botón en el Tres pulsaciones rápidas: necesario; digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide prueba de alcance efectivo accesorio. Si el hub emite un mensaje de voz, significa que el accesorio reasonable protection against harmful interference in a residential installation. Haga doble clic y mantenga durante y el sensor se están comunicando correctamente. This equipment generates uses and can radiate radio frequency energy and, if not installed cinco segundos: Restablecimiento de fábrica Tierra Normalmente de color verde. and used in accordance with the instructions, may cause harmful interference to radio communications. Luz indicadora Installation Descripción de la luz indicadora However, there is no guarantee that interference will not occur in a particular installation. If Neutro this equipment does cause harmful interference to radio or television reception, which can Visitar en www.aqara.com/support para obtener más información. Generalmente blanco. Estado de la luz indicadora Descripción del estado be determined by turning the equipment off and on, the user is encouraged to try to correct 1. Desconecte la alimentación del switch que se vaya a sustituir antes de the interference by one or more of the following measures: La luz azul parpadea rápidamente Se está estableciendo conexión con la la instalación (apague y encienda la luz varias veces para comprobar red Zigbee - Reorient or relocate the receiving antenna. Línea/Carga - Increase the separation between the equipment and receiver. que se ha desconectado la alimentación). Obligatorio, normalmente de color Luz azul fija La red Zigbee funciona correctamente - Connect the equipment into an outlet on a circuit different from that to which the receiver negro, siempre presente. is connected. La luz roja parpadea rápidamente Alarma de sobrecarga y temperatura alta - Consult the dealer or an experienced radio/TV technician for help. * Este producto debe utilizarse con un dispositivo con funcionalidad de puerta de FCC Radiation Exposure Statement enlace. Algunas funciones requieren compatibilidad con modelos de puerta de La luz roja parpadea lentamente No hay conexión con la red Zigbee enlace específicos. Para una lista detallada, visite: www.aqara.com/support 4. Extraiga la cubierta de superficie y fije el switch a la caja de interruptores This equipment complies with FCC radiation exposure limits set forth for an uncontrolled OFF ON OFF ON con tornillos. (Nota: no apriete demasiado los tornillos para no deformar environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. el switch) OFF ON OFF ON Advertencia Especificaciones OFF ON OFF ON IC: 22635-AK024 1. La instalación de un switch inteligente requiere ciertos conocimientos Modelo: QBKG16LM IC NOTICE TO CANADIAN USERS OFF OFF ON en materia de electricidad. Para su seguridad personal, se recomienda Dimensiones: 120 x 74 x 36,5 mm（4,72 x 2,91 x 1,44 pulgadas) This device complies with Industry Canada license‐exempt RSS standard(s). Operation is pedir ayuda a un electricista cualificado para la instalación. OFF OFF ON Protocolo inalámbrico: Zigbee3.0 subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired 2. Este producto ha sido diseñado exclusivamente para uso en interiores; Entrada: 120 VCA, 60 Hz operation of the device. This device complies with RSS‐247 of Industry Canada. no lo utilice en un entorno húmedo. Cargas máximas: 1200W (total, incandescente), 200W/vía (CFL/LED), Operation is subject to the condition that this device does not cause harmful interference. 3. No instale el producto cerca de una fuente de calor. 1/4HP (total) This Class B digital apparatus complies with Canadian ICES‐003 (Cet appareil numérique Temperatura de funcionamiento: 0 – 40° C（32 – 104° F） de la Classe B conforme à la norme NMB‐003 du Canada). Humedad de funcionamiento: 0 – 95% HR, sin condensación 美标墙壁开关（零火双键）说明书 正反面印刷 料号：3020320 材质：金东太空梭105G无光铜纸


Document Created: 2019-04-12 09:40:07
Document Modified: 2019-04-12 09:40:07
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC