user manual

FCC ID: 2AKIT-AK022

Users Manual

Download: PDF
FCCID_4234670

Smart Wall Switch (No Neutral, Double Rocker) Before you install 2. Remove the existing switch and identify the wires with wire labels. 5. Install the wall plate, turn main power ON at the circuit breaker, and test Manufacturer: Lumi United Technology Co., Ltd. the switch by pressing the button; Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian This product is only used to replace a single pole switches rather than a Ground If it doesn’t work, please check: a. If the wiring is correct; b. If the power Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. Product Profile 3-way switch. Usually green. is restored. Online Customer Service: www.aqara.com/support If it works, add the switch to the app following the next steps; Email: support@aqara.com Neutral Required, but not always present, usually white. Quick Setup 1. Please add the Hub to the app according to the Hub Quick Start Guide. Line(Hot)/Load Required, usually black, and always 2. Please open the app, and then tap “+” in the top right corner to enter present. “Add Device (Accessory)” page. Select “Smart Wall Switch (No Push Button Neutral, Double Rocker)”, and add it according to instructions. Short Press Once: Turn on/off *If the connection fails, please move the hub closer to the switch, connect to Long Press for 5s: Reconnect 3. Install the smart wall switch and connect wires as required. power and try again. Quick Press 3 Times: Effective Range Test Ground Effective Range Test: Quick press the button on the device 3 times. If the Usually green. Hub makes voice prompts, it indicates that the device can communicate effectively with the Hub. Indicator Light Neutral Installation Required, but not always present, Indicator Light Description usually white. Visit www.aqara.com/support for more information. Indicator Light Status Status Description 1. Turn off power at circuit breaker or fuse box and test that power is off Blue light blinks quickly Zigbee network is connecting Line(Hot)/Load before wiring. (Please switch the light several times to make sure that Required, and always present. Blue light keeps on Zigbee network works properly the power has been disconnected) Red light blinks quickly High temperature alarm 4. Tuck the wires into the wall box leaving room for the smart switch. Using Red light blinks slowly Zigbee network is not connected * This product requires a compatible hub. Some features require a specific hub. the screws provided, mount the smart switch to the wall box. Be careful For the detailed list, please visit: www.aqara.com/support not to crush any wires. (Note: avoid overtightening the screws.) OFF ON OFF ON Specification OFF ON OFF ON Warning Model: QBKG14LM OFF ON OFF ON Dimensions: 120 x 74 x 36.5 mm (4.72 x 2.91 x 1.44 in) 1. A certain amount of electrical knowledge is required to install a smart wall switch. For your safety, we recommend that you ask a qualified OFF OFF ON Wireless Protocol: Zigbee3.0 electrician to help you install it; Input: 120 V AC 60Hz OFF OFF ON Min Load: 3 W/way (Incandescent), 5 W/way (CFL/LED), typical load Smart Wall Switch (No Neutral, Double Rocker) 2. This product is for indoor use only; do not use it in humid environment; Max Load: 600 W/way (Incandescent), 200W/way (CFL/LED), 1/4 HP 3. Do not install this product near a heat source. Operating Temperature: 0 – 40°C（32 – 104°F） Operating Humidity: 0 – 95% RH, non-condensing Switch de pared inteligente (sin neutro, basculante doble) Antes de la instalación 2. Retire el switch que se vaya a sustituir y marque el cable con la etiqueta 5. Coloque la cubierta de superficie del switch, conecte la alimentación y Fabricante: Lumi United Technology Co., Ltd. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of de cables para identificar el cable correspondiente en la instalación. controle con el botón; si el control no funciona, compruebe que las Dirección: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Verifique la compatibilidad 20 cm between the radiator and your body. This transmitter must not be co-located or conexiones sean correctas y que se haya conectado la alimentación; si Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. operating in conjunction with any other antenna or transmitter. Perfil del producto Este producto solo puede sustituir switches de control sencillo en lugar de Tierra funciona, siga los pasos a continuación para agregar el producto. Servicio de atención al cliente en línea: www.aqara.com/support Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils switches de doble control. normalmente de color verde. Correo electrónico: support@aqara.com radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter Configuración rápida tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en Neutro Obligatorio, pero no siempre presente. 1. Agregue el hub a la aplicación de acuerdo con la Guía rápida del hub. FCC ID: 2AKIT-AK022 compromettre le fonctionnement. Federal Communications Commission (FCC) compliance statement Cet équipement est conforme aux limites IC d'exposition aux radiations définies pour un 2. Abra la aplicación, pulse «+» en la parte superior derecha para acceder 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance a la página «Add Device (Accessory)» (Agregar dispositivo minimale de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être situé ou Línea/Carga two conditions: [accesorio]). Seleccione Switch de pared inteligente (sin neutro, (1) This device may not cause harmful interference. opérant en conjonction avec une autre antenne ou émetteur. Obligatorio, normalmente de color negro, Botón siempre presente. basculante doble) y siga las instrucciones para agregarlo. (2) This device must accept any interference received, including interference that may *Si falla la conexión, acerque el switch de pared al hub, conéctelo y vuelva a cause undesired operation. Pulsación corta: encender/apagar intentarlo. 2. Changes or modifications not expressly approved by the party responsible for Pulsación larga durante cinco segundos: volver a conectar 3. Instale el switch de pared inteligente y conecte el cable según sea compliance could void the user's authority to operate the equipment. Prueba de alcance efectivo: pulse rápidamente tres veces el botón en el Tres pulsaciones rápidas: necesario; NOTE: This equipment has been tested and found to comply with the limits for a Class B prueba de alcance efectivo accesorio. Si el hub emite un mensaje de voz, significa que el accesorio digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide Tierra y el sensor se están comunicando correctamente. reasonable protection against harmful interference in a residential installation. normalmente de color verde. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio Luz indicadora Descripción de la luz indicadora Installation communications. Neutro However, there is no guarantee that interference will not occur in a particular installation. If Visitar en www.aqara.com/support para obtener más información. Obligatorio, pero no siempre Estado de la luz indicadora Descripción del estado this equipment does cause harmful interference to radio or television reception, which can presente. Se está estableciendo conexión con la be determined by turning the equipment off and on, the user is encouraged to try to correct 1. Desconecte la alimentación del switch que se vaya a sustituir antes de La luz azul parpadea rápidamente red Zigbee the interference by one or more of the following measures: la instalación (apague y encienda la luz varias veces para comprobar - Reorient or relocate the receiving antenna. Luz azul fija La red Zigbee funciona correctamente que se ha desconectado la alimentación). Línea/Carga - Increase the separation between the equipment and receiver. Obligatorio, siempre presente. - Connect the equipment into an outlet on a circuit different from that to which the receiver La luz roja parpadea rápidamente Alarma de alta temperatura is connected. - Consult the dealer or an experienced radio/TV technician for help. * Este producto debe utilizarse con un dispositivo con funcionalidad de puerta de La luz roja parpadea lentamente No hay conexión con la red Zigbee enlace. Algunas funciones requieren compatibilidad con modelos de puerta de 4. Extraiga la cubierta de superficie y fije el switch a la caja de FCC Radiation Exposure Statement enlace específicos. Para una lista detallada, visite: www.aqara.com/support interruptores con tornillos. (Nota: no apriete demasiado los tornillos This equipment complies with FCC radiation exposure limits set forth for an uncontrolled OFF ON OFF ON environment. This equipment should be installed and operated with minimum distance para no deformar el switch) Especificaciones 20cm between the radiator & your body. OFF ON OFF ON Modelo: QBKG14LM Advertencia IC: 22635-AK022 OFF ON OFF ON Dimensiones: 120 x 74 x 36,5 mm（4,72 x 2,91 x 1,44 pulgadas) 1. La instalación de un switch inteligente requiere ciertos conocimientos Protocolo inalámbrico: Zigbee3.0 IC NOTICE TO CANADIAN USERS en materia de electricidad. Para su seguridad personal, se recomienda OFF OFF ON This device complies with Industry Canada license‐exempt RSS standard(s). Operation Entrada: 120 VCA, 60 Hz is subject to the following two conditions: (1) This device may not cause interference, and pedir ayuda a un electricista cualificado para la instalación. OFF OFF ON Cargas mínimas: 3W/vía (incandescente), 5W/vía (CFL/LED), carga típica (2) This device must accept any interference, including interference that may cause 2. Este producto ha sido diseñado exclusivamente para uso en interiores; Cargas máximas: 600W/vía (incandescente), 200W/vía (CFL/LED), undesired operation of the device. This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful no lo utilice en un entorno húmedo. 1/4HP (total) interference. This Class B digital apparatus complies with Canadian ICES‐003 (Cet 3. No instale el producto cerca de una fuente de calor. Temperatura de funcionamiento: 0 – 40°C（32 – 104°F） appareil numérique de la Classe B conforme à la norme NMB‐003 du Canada). Humedad de funcionamiento: 0 – 95% HR, sin condensación


Document Created: 2019-04-08 16:38:51
Document Modified: 2019-04-08 16:38:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC