user manual

FCC ID: 2AKI8-ONN008

Users Manual

Download: PDF
FCCID_3301608

FCC ID:2AKI8-ONN008? Front Cover Connecting the Transmitter Using Wireless Headphone Wired Headphone using Tips for setting & reception Troubleshooting tips NOTE 1. Turn the Headphone on by moving the switch located on the side of the When the headphones are turned off, use the audio cable to plug in Tips for volume setting I cannot turn the Headphone on This equipment has been tested and found to comply with the limits for a Class B digital device, headphone into the "ON" position. The Red LED indicator light will turn on. your audio device. If you connect the transmitter to the headphone jack of the A/V component, set the volume of the A/V component Replace the batteries in the headphone, and make sure the switch is in “ON” pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 2. When the Transmitter turns off, pressing “RESET” located on front of Listen to sound as a standard wired headphone. as high as possible but not so high that the audio signal becomes distorted. against harmful interference in a residential installation. This equipment generates uses and can When watching videos, be careful not to raise the volume too high in quiet scenes. You may hurt your ears I cannot turn the Transmitter on radiate radio frequency energy and, if not installed and used in accordance with the instructions, headphone then press “SCAN” located on front of headphone, can listen Replace the batteries in the headphone when a loud scene is played. may cause harmful interference to radio communications. However, there is no guarantee that the radio. Make sure the Power Adapter is properly connected Tips for better reception interference will not occur in a particular installation. If this equipment does cause harmful 3. Adjust the listening volume to comfortable level using the headphone's Make sure the switch is on CH1, CH2 or CH3 interference to radio or television reception, which can be determined by turning the equipment audio volume control. Receiving performance This system utilizes signals in the 88-40MHz band so the receiving performance may I cannot listen the music off and on, the user is encouraged to try to correct the interference by one or more of the Smartphone cable yellow white deteriorate due to the surroundings. The following examples illustrate conditions that may reduce the reception Make sure the Transmitter and Headphone are turned on following measures: red TV range or cause interference. Make sure the audio cable is connected well Wireless Headphones With Transmitter - Inside a building with walls containing steel beams. Make sure headphone is connected to the correct channel - Reorient or relocate the receiving antenna. - An ares with many steel file cabinets, etc. - Increase the separation between the equipment and receiver. - An area with many electrical appliances capable of generating electromagnetic fields Ensure that you are within approximately 30 feet of the Transmitter -Connect the equipment into an outlet on a circuit different from that to which the Audio Y RCA adapter Red LED -The transmitter is placed on a metal instrument. I cannot listen the music when 2 or 3 headphones are working with receiver is connected. - An area facing a roadway indicator audio cable plugged - Noise or interfering signals exist in the surroundings due to radio transceivers in trucks, etc. one Transmitter -Consult the dealer or an experienced radio/TV technician for help PC light turns on in "AUDIO" - Noise or interfering signals exist in the surroundings owing to wireless communication systems installed along Make sure the switch in on “ON” of the headphone press "RESET" roadways. Press “RESET” then press “SCAN”, make sure connect the right channel Changes or modifications not expressly approved by the party responsible for compliance FCC ID:2AKI8-ONN008 NOTE: One Transmitter can be connected to 3 sets of headphones. On each Effective area of the transmitter Interfere with signal when 2 or 3 Transmitter is are working could void the user's authority to operate the equipment. The optimum distance is up to approximately 9.1 m( 30ft) without the system picking up some interference. headphone press "RESET" press "SCAN" and up to 3 headphones can listen to NOTE: When not using the Transmitter or Headphone please turn them off However, the distance may vary depending on the surroundings and environment. Make sure the Transmitters are in different channel This device complies with Part Model: ONA17AA008 sound from one 1 device. If using 2 or 3 Transmitters at the same time each press "SCAN" - If the system picks up some noise whthin the above mentioned distance, reduce the distance between the Make sure the Transmitters are set to different channels 15 of the FCC Rules. Operation is subject to the following two conditions: Transmitter will need to be set to a different channel. For example: the first and remove batteries. If Transmitter will not be in use for a prolonged transmitter and the headphones, or select another channel. Press "RESET" then press "SCAN", make sure it is connecting to the correct channel (1) this device may not cause harmful interference, and Transmitter switch set to CH1, the second Transmitter switch set to CH2, and Switch to "ON" position Adjust to a comfortable volume time unplug the power adapter from the electrical outlet. - When you use the headphones inside the effective area of the transmitter, the transmitter can be placed in any Has noise or interfere when listening (2) this device must accept any interference received, including interference that may PRODUCT GUIDE direction from the listener. cause undesired operation. the third Transmitter switch set to CH3. This way the listener can select which - Even within the signal reception area, there are some spots (dead spots) where the RF signal cannot be received. Make sure the transmit distance is within 30feet(9.1M) Transmitter they want to listen to with no interference. This characteristic is inherent to RF signals, and does not indicate malfunction. By slightly moving the transmitter, Make sure the transmitter and receiver are in the visible range， no obstacles A general, cautionary and warning marking intended to inform the user of a potential risk of location of the dead spot can be changed. or straighten the audio cable between transmitter and device. Make sure no strong interference signals fire, electrical shock, or injury to persons shall be provided. Make sure the audio cable is in straighten, non winding Version 1 P8 P9 P10 P11 P12 P13 WARNING In the box Headphone controls Transmitter controls Battery Installation: Using the 5V Power Adapter: Using the Transmitter To reduce the risk of fire or electric shock, do not expose this apparatus Headphone: To use the Power Adapter: 1. Connect the Transmitter to the “Audio”jacks of your audio device for to rain or moisture. 1.Place the Transmitter in the supplied cradle. example: Smartphone, PC, TV, using the supplied cables and adapters. 1. Open the battery compartment by sliding the latch downward located on left To reduce the risk of fire or electric shock, do not expose this apparatus to dripping 2.Connect the Power Adapter to the transmitter’s Cradle. (NOTE: when connecting the Transmitter to the Television, the RCA “Audio-Out” side of the headphone. or splashing, and do not place objects filled with liquids, such as vases, on the 3.Plug the Power Adapter into a nearby electrical outlet. jacks are located on the back of your TV Set, not the front.) 2. Put in 2*AAA batteries. Made sure they are placed in compartment with the apparatus. 2. Make sure that your audio device is turned on and set to a reasonable polarity in the correct position(+/-). Do not expose the batteries (battery pack or batteries installed) to excessive heat listening volume. such as sunshine, fire or the like for a long time. 3. Close the compartment by sliding the cover back on & closing the latch. NOTE: Make sure the Power Adapter is the correct voltage. Failure to do so 3. Turn on the Transmitter by moving the switch on the back of the Transmitter To avoid electrical shock, do not open the cabinet. Refer servicing to qualified may cause damage to the transmitter. to CH1/CH2/CH2. The Red LED indicator light on the front of the unit will personnel only. NOTE: Do not mix old and new batteries turn on. Reset Key Do not install the appliance in a confined space, such as a bookcase or built-in Scan Key cabinet. As the main plug of AC power adapter is used to disconnect the AC power adapter ON/OFF Audio from the mains, connect it to an easily accessible AC outlet. Should you notice an Volume control abnormality in it, disconnect it from the AC outlet immediately. Headphone Transmitter LED light Audio Red LED Excessive sound pressure from earphones and headphones can cause hearing LED light Use the switch OFF/channel switch to select indicator loss. light turns on CH1/CH2/CH3 AC socket Wireless Headphones With Transmitter Model: ONA17AA008 PRODUCT GUIDE Version 1 Battery Compartment Note: Transmit distance is approximately 30 feet(9.1m). maximum line-of-sight, Product Guide AC adapter Audio Y RCA adapter Audio cable no interference P1 P2 P3 P4 P5 P6 P7


Document Created: 2017-02-14 11:18:42
Document Modified: 2017-02-14 11:18:42
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC