User Manual

FCC ID: 2AK7XHS1DSZ

Users Manual

Download: PDF
FCCID_3381767

This is a intelligent door sensor, adopts super low power Z- Smart Door Sensor Wave wireless networking technology, makes a longer Step 1 Step 2 User Manual battery life-span, Feel open or close state of the door or window through the near and separation between sensor 1.Working Voltage: DC3V（2×AAA battery） 2.Static Current: ≤5uA Technical Parameters Function renderings HS1DS-Z and magnetic. Dual sensor design, makes the installation 3.Alarm Current: ≤35mA more flexible and adaptable. Products are suitable for Product Description home, villas, factories, shops, warehouses, office 4.Detecting Distance: ＞15mm buildings, banks, room and other places of safety 5.Networking: Z-Wave Ad-Hoc Network prevention. 6.Wireless Networking Distance: ≥70 metres （in the open area） networking button 7.Working Environment: -10℃ ～ +50℃ Networking Indicator 8.Working Humidity: Maximum 95%RH 9.Detector Dimension: 76×36.6×16.5 mm 10.Magnet dimension: 76×13.9×16.5 mm Sensor Magnet Remove insulator make device on power. Click the “add” button to enter the networking mode. *Please read the user manual carefully before operation. The guide picture is for reference only, please in kind prevail. 1 2 3 4 5 Step 3 Step 4 Step 5 Step 6 Anti-tamper Key - + Restore factory settings Battery replacement - + + - + - Please change the battery according to negative Connecting network: According to the APP tip, press the and positive of the battery. device networking hole for 3 times in 1.5 seconds, then the Please deal with waste batteries correctly for green LED flashes quickly (connecting network within 30 environmental protection. seconds), and “networking succeed “ will be displayed on app interface. Tear off the gummed film, stick the equipment on the Statement Disconnecting network: Click the “delete device” button on Align the installation, the installation distance is less Long press the networking button,then power on (put into required area.Sensor should be installed in fixed area *Instruction is for reference only, please prevail in kind. APP, then quick press networking hole for 3 times in 1.5 than 15mm. (The magnet part can be installed both battery),ID code is clear and recover to factory setting. *Because of the updating of the technology, the final interpretation right like door frame, magnet can be installed in active area Install sensors into the bracket. seconds, green LED flashes for 6 times, disconnecting sides of detector part) owned by factory, if there are any inconformities when using this products network succeed. like door plank, this picture for reference only. under this instruction. 6 7 8 9 10 11

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Document Created: 2019-10-18 14:44:07
Document Modified: 2019-10-18 14:44:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC