User Manual

FCC ID: 2AK7XHS1CGZ

Users Manual

Download: PDF
FCCID_3381789

1.Shell surface will be slightly hot while working, which is Before installation, pls confirm the detecting gas density, Smart Combustible Gas Sensor a normal phenomenon . heavier or lighter than air. If detecting gas is heavier than 1.Working Voltage: AC100V～240V User Manual 2.Please dismantle sensor while decorating house. air: LPG., etc, install at 0.3-1m height from floor, semi- 3.Avoid spraying aerosol around sensor. diameter to gas source less than 1.5m. If detecting gas is HS1CG-Z This Smart Combustible Gas Sensor adopts super low 2.Average Power Consumption: ＜1.5W lighter than air: natural gas, manufactured gas, marsh power consumption Z-Wave wireless networking 4.Oil contamination around gas convection holes will Appearance Instruction 3.Alarm Sound: 75dB/1m gas., etc, install at 0.3-1m height from ceiling, semi- Product Introduction effect the sensitivity of gas sensor, after long time Functional Diagram technology. It is used for detecting combustible gas Networking Hole diameter to gas source less than 1.5m. using.Suggest users to clear gas convection holes with Warm Prompt 4.Alarm Density: 6%LEL±3%LEL(natural gas) Specification leakage and preventing harm caused by gas leakage. it Test Button brush mixing little detergent every 3 months (or Ceiling also can be used as Z-Wave repeater to extend wireless 5.Networking: Z-Wave Ad-hoc Networking depends on specific oil contamination level). LED Indicator sensor communication distance. It adopts high stability semi- Avoidletting detergent enter sensor body. Please retest 6.Wireless Networking Distance: ≥70m (in open area) after cleaning. conductor gas sensor, with high stability, little sensitivity drift and may other features. Sensor alarms while gas 7.Working Environment: -10℃ ～ +50℃ 5.Semi-conductor of gas sensor supports 5-year lifespan. density in air exceed alarm level. It is applicable for Gas Convection Holes Please replace sensor timely. Max diameter 3m 8.Environment Humidity: Max 95% RH kitchen or possible gas leakage in door areas. 6.Please do not use lighter to test sensor directly in case 9.Dimension: 79*68*31mm (no including plug) of any damage to gas sensor inside. 7.For your safety, in addition to use sensor properly, please be vigilant and enhance safety prevention awareness in daily life. Gas stove Floor Please read the user manual carefully before operation. The guide picture is for reference only. Please in kind prevail. 1 2 3 4 5 Light State Product Testing Emergency alarm treatment Fault analysis and troubleshooting The detector will keep alarming while the natural gas or LPG density in air exceeds the alarm level. Pls do relative Power On & Preheating State Color Light Alarm Sound treatments as below: Networking Mode Factory Default Power Constantly Lit None 1.Shut down the tube valve right away. 2.Extinguish all fire sources and do not use anything can Alarm Flashing "Di-Di” Alarm Sound make fire, e.g. lighters, matches., etc. Malfunction Constantly Lit Constantly Buzzing 3.Avoiding switches on various electric equipments. 4.Open the window and make the air flow rapidly. 可燃气体报警器 红外探测器 门磁探测器 Symptom Reason Remedy Test button of this sensor is used for testing whether LED Network: According to APP prompting, please press indicator and buzzer can work properly. Red LED and yellow 1. Power on detector and Always warming up 1. Long time no power; networking hole for 3 times in1.5 seconds, then green LED LED flash alternatively with buzzer alarming when test button after power on(LED aging test for 24 hours; 2. Test gas detector will flash quickly(the longest networking time is 30 seconds), pressed. keeps flashing) when warming up. 2. F Do not test detectors APP interface will display icon, networking successfully. when warming up. Power on the sensor, the green LED will be lit and a “beep” sounded, the sensor enters into preheating state. At this time, red LED and Disconnecting: Please click delete key of the device, then Factory Default: Long press networking hole for 10 seconds, Yellow LED keeps on and yellow LED flash alternately. The flash will stop 3 minutes later, Gas sensor fault Contact dealer to repair Please click the add button ( “ + ” ) to enter gateway press networking hole for 3 times in 1.5 seconds, then green then ID code will be cleared and the sensor will be reset to buzzer keeps beeping which indicates that the sensor is in normal working state. (Don't use networking mode. gas to test sensor while preheating). LED will flash slowly for 6 times, disconnecting successfully. factory default. 6 7 8 9 10 11

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Document Created: 0000-00-00 00:00:00
Document Modified: 0000-00-00 00:00:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC