User Manual

FCC ID: 2AK7XHS1CAZ

Users Manual

Download: PDF
FCCID_3381800

1, This product can not be used for detecting natural 1 . Install the sensor in bedroom and living area or To increase safety factors in single-layer house, 1.Working Voltage：DC3V(CR123A Lithium Battery) gas(methane), propane, butane and other suggest to install at least a sensor in each bedroom and Smart Carbon Monoxide Sensor This product is a smart carbon monoxide 2.Static Current：≤20uA combustible gas. anywhere CO may leak, make sure each sleeping install a sensor at 6m from chimney and gas fixture. area can hear sound alarm when choose User Manual sensor, adopts super low power consumption Z- 3.Alarm Current：≤60mA 2, Clean once a month, users may use household installation position. To increase safety factors in multi-layer house, suggest wave wireless networking technology, used for vacuum cleaner and soft brush when cleaning. 2.Avoid suppressing or falling down sensors, keep to install at least a sensor in each bedroom, install at 4.Alarm Sound：85dB/1m 3, Do not use cleanser or solvent wipe sensors, Installation Instruction HS1CA-Z detecting carbon monoxide. Sensor adopts high Installation Drawing sensors away from humid, high voltage, strong least one sensor in basement. Please install a sensor at Product Introduction 5.Alarm Sensitivity：30ppm 120mins alarm please avoid spraying air freshener, hair spray, oil Technical Data performance electrochemical sensor, support magnetic and children. 6m from chimney and gas fixture. sound and flash alarm, It has high stability, super 50ppm 60-90mins alarm paint or other aerosol near sensors. 3 . Do not suggest install sensors in garage, kitchen, 100ppm 10-40mins alarm Tips low power consumption, little sensitivity drift and 4, Effective working life span is 5 years, suggest 300ppm 3mins alarm boiler and places where sensor may false alarm. many other features. Free installation design, replace every 5 years no matter there is fault or 6.Networking：Z-wave Ad-Hoc Networking Do not install in dirty, dusty or greasy places, oily, support instant bonding. not. (Battery life span is 3 years). 5, Please be attention when alarm happens. Shut-off dust or household chemicals may damage internal 7.Wireless Networking Distance：≥70m(open area) Bedroom Bedroon Bedroom valves immediately, opening the window, make sensor, and make sensor can not work normally. 8.Working Temperature：-10℃ ～ +50℃ 4.Sensors can support wall mounted or placing on Gagrage Kitchen sure indoor airiness. Besides using sensors Aisle Networking Hole 9.Environment Humidity：≤ 95%RH the table, household and travel essential. Livingroom LED Indicator c o r r e c t l y, u s e r s s h o u l d s t r e n g t h e n t h e 10.Dimension：60* 60*49.2mm Minimum recommended installation consciousness of fire protection. Basement Sensor Installation Base Additional recommended installation * Please read the user manual carefully before operation. The guide picture is for reference only. please in kind prevail 1 2 3 4 5 Installation Step1 Installation Step2 Installation Step3 Installation Step4 Status and battery replacement Troubleshooting and test Status LED Indicator Alarm Please take following advices for reference if sensors can not work normally: Test Green-red-yellow-green LED flash alternatively once 4 beeps 1.Replace battery in time, if voltage too low and reach effective life span. (Check table 1 for state reference) Preheating Green,red and yellow LED flash alternatively once 1 beep 2.Please clean sensor if the fault resulted from dust or oil stain ( Check table Alarm Red LED flash 4 beeps 1for state reference). Malfunction Yellow LED flash twice every 10 seconds 2 beeps every 10 seconds 3.Make sure sensors screw into the base correctly. Low battery Green LED flash every 53 seconds 1 beep every 53 seconds Normal working Red LED flash every 53 seconds \ Expired sensor Yellow LED flash twice 4 beeps every 10 seconds Chart1 According to APP prompt, press the networking button 3 times in 3A C R 12 1.5 seconds until green light flash, (the longest networking time Press test button on the product for 3 seconds, shows in above is 30 seconds) APP interface prompted, networking success. picture, till alarm happens ( check table 1 for state reference). Anticlockwise rotating the bracket out from the installation Click “Add Device” on the APP interface, and Select device, click "delete" on APP, then press the Screw the sensor into bracket, please remove the base, then remove the battery insulating strip to make enter the networking mode. networking button 3 times in 1.5 seconds until the green light double - sided adhesive membrane on the Suggest test sensor at least once a week. Please pay attention once detector on power. flashes slowly for 6 times, which indicates network is installation base, and stick on the wall. *Please replace battery correctly, following the battery posi tive and alarm happens. disconnected successfully negative electrode. 6 7 8 9 10 11

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Document Created: 2019-10-18 14:47:07
Document Modified: 2019-10-18 14:47:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC