Report_DFS_Rev 1

FCC ID: 2AJVQ-7668AUC

Test Report

Download: PDF
FCCID_4291073

Qingdao Intelligent&Precise Electronics Co., Ltd RF TEST REPORT SCOPE OF WORK: FCC Part 15.407 & ISED RSS-247 RF report Model: ZDGF7668AU-C REPORT NUMBER: 190400328SHA-003 ISSUE DATE: April 26, 2019 DOCUMENT CONTROL NUMBER TTRFFCCDFS-01_V1 © 2018 Intertek

Intertek Testing Services Shanghai, Building No.86, 1198 Qinzhou Road (North), Caohejing Development Zone, Shanghai 200233, China TEST REPORT Telephone: 86 21 6127 8200 www.intertek.com Report no. 190400328SHA-003 Applicant: Qingdao Intelligent&Precise Electronics Co., Ltd No.218, Qianwangang Road, Qingdao Economic&Technological Development Zone, Shandong, China. Manufacturer: Qingdao Intelligent&Precise Electronics Co., Ltd No.218, Qianwangang Road, Qingdao Economic&Technological Development Zone, Shandong, China. Factory 1: Qingdao Intelligent&Precise Electronics Co., Ltd No.218, Qianwangang Road, Qingdao Economic&Technological Development Zone, Shandong, China. FCC ID: 2AJVQ-7668AUC IC: 22470-7668AUC Summary The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2018): Radio Frequency Devices RSS-247 Issue 2 (February 2017): Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices KDB 905462 D02 UNII DFS Compliance Procedures New Rules v02: Compliance Measurement Procedures for Unlicensed-National Information Infrastructure Devices Operating In The 5250-5350 MHz and 5470-5725 MHz Bands Incorporating Dynamic Frequency Selection KDB 905462 D03 NII Clients Without Radar Detection New Rules v01r02: U-NII CLIENT DEVICES WITHOUT RADAR DETECTION CAPABILITY PREPARED BY: REVIEWED BY: Project Engineer Reviewer Nemo Li Daniel Zhao This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCDFS-01_V1 © 2018 Intertek Page 2 of 22

Report No. 190400328SHA-003 TEST REPORT Contents REVISION HISTORY................................................................................................................................................ 4 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 5 1 GENERAL INFORMATION ............................................................................................................................. 6 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 6 1.2 RF TECHNICAL INFORMATION ................................................................................................................................ 6 1.3 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 7 2 TEST SPECIFICATIONS ................................................................................................................................... 8 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 8 2.2 MODE OF OPERATION DURING THE TEST................................................................................................................... 8 2.3 TEST PERIPHERALS USED ....................................................................................................................................... 8 2.4 INSTRUMENT LIST ................................................................................................................................................ 9 3 DFS DETECTION THRESHOLDS AND RADAR TEST WAVEFORMS .................................................................. 11 3.1 INTERFERENCE THRESHOLD VALUES ....................................................................................................................... 11 3.2 DFS RESPONSE REQUIREMENT VALUES .................................................................................................................. 11 3.3 RADAR TEST WAVEFORMS MINIMUM STEP............................................................................................................ 12 3.4 TEST RESULT..................................................................................................................................................... 12 3.5 LONG PULSE RADAR TEST WAVEFORM .................................................................................................................. 14 3.6 FREQUENCY HOPPING RADAR TEST WAVEFORM ..................................................................................................... 15 3.7 CALIBRATION SETUP........................................................................................................................................... 16 3.8 RADAR WAVEFORM CALIBRATION PROCEDURE ....................................................................................................... 17 3.9 RADAR WAVEFORM CALIBRATION RESULT .............................................................................................................. 18 4 IN-SERVICE MONITORING FOR CHANNEL MOVE TIME, CHANNEL CLOSING TRANSMISSION TIME AND NON- OCCUPANCY PERIOD ........................................................................................................................................... 20 4.1 CHANNEL MOVE TIME, CHANNEL CLOSING TRANSMISSION TIME ............................................................................... 21 4.2 NON-OCCUPANCY PERIOD .................................................................................................................................. 22 TTRFFCCDFS-01_V1 © 2018 Intertek Page 3 of 22

Report No. 190400328SHA-003 TEST REPORT Revision History Report No. Version Description Issued Date 190400328SHA-003 Rev. 01 Initial issue of report April 26, 2019 TTRFFCCDFS-01_V1 © 2018 Intertek Page 4 of 22

Report No. 190400328SHA-003 TEST REPORT Measurement result summary TEST TEST ITEM FCC CLAUSE IC CLAUSE RESULT Initial Channel Availability Check Time 15.407(h)(2) RSS-247 clause 6.3 NA Radar Burst at the Beginning of the Channel Availability Check & End of the 15.407(h)(2) RSS-247 clause 6.3 NA Channel Availability Check Time Channel Move Time, Channel Closing 15.407(h)(2) RSS-247 clause 6.3 Pass Time Non-occupancy period 15.407(h)(2) RSS-247 clause 6.3 Pass UNII Detection Bandwidth Measurement 15.407(h)(2) RSS-247 clause 6.3 NA Statistical Performance Check 15.407(h)(2) RSS-247 clause 6.3 NA Notes: 1: NA =Not Applicable 2: This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCDFS-01_V1 © 2018 Intertek Page 5 of 22

Report No. 190400328SHA-003 TEST REPORT 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: Wireless Module Type/Model: ZDGF7668AU-C EUT is a Wireless Module with WiFi and Bluetooth function, and has Description of EUT: only one model. Rating: DC 5V EUT type: Table top Floor standing Software Version: / Hardware Version: / Sample received date: April 2, 2019 Date of test: April 2, 2019 ~ April 25, 2019 1.2 RF Technical Information Specification Items Description 802.11a, 802.11n(HT20), 802.11n(HT40), 802.11ac(VHT20), Protocol 802.11ac(VHT40), 802.11ac(VHT80) Modulation BPSK, QPSK, 16QAM, 64QAM,256QAM Channel Frequency 5250-5350MHz; 5470-5725MHz Channel Bandwidth 20/40/80MHz Max. EIRP Power < 200mW ≥ 200mW Master Operating Mode Client without Radar Detection Client with Radar Detection Manufacturer Statement Manufacturer statement confirming that information regarding the parameters of the detected Radar Waveforms are not available to the end user. TTRFFCCDFS-01_V1 © 2018 Intertek Page 6 of 22

Report No. 190400328SHA-003 TEST REPORT 1.3 Description of Test Facility Name: Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is CNAS Accreditation Lab recognized, Registration No. CNAS L0139 certified, or FCC Accredited Lab accredited by these Designation Number: CN1175 organizations: IC Registration Lab CAB identifier.: CN0051 VCCI Registration Lab Registration No.: R-14243, G-10845, C-14723, T-12252 A2LA Accreditation Lab Certificate Number: 3309.02 TTRFFCCDFS-01_V1 © 2018 Intertek Page 7 of 22

Report No. 190400328SHA-003 TEST REPORT 2 TEST SPECIFICATIONS 2.1 Standards or specification 47CFR Part 15 (2018): Radio Frequency Devices RSS-247 Issue 2 (February 2017): Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices KDB 905462 D02 UNII DFS Compliance Procedures New Rules v02: Compliance Measurement Procedures for Unlicensed-National Information Infrastructure Devices Operating In The 5250-5350 MHz and 5470-5725 MHz Bands Incorporating Dynamic Frequency Selection KDB 905462 D03 NII Clients Without Radar Detection New Rules v01r02: U-NII CLIENT DEVICES WITHOUT RADAR DETECTION CAPABILITY 2.2 Mode of operation during the test Stream the channel loading test file from the Master Device to the Client Device on the test Channel for the entire period of the test if necessary. 2.3 Test peripherals used Item No Description Manufacturer Model No. Note 1 Laptop computer HP 4230s - Digital Home ONU FCC ID: 2 Alcatel-Lucent A-240Z-A (Master) 2ADZRA240ZA TTRFFCCDFS-01_V1 © 2018 Intertek Page 8 of 22

Report No. 190400328SHA-003 TEST REPORT 2.4 Instrument list Conducted Emission/Disturbance Power/Tri-loop Test/CDN method Used Equipment Manufacturer Type Internal no. Due date ☒ Test Receiver R&S ESCS 30 EC 2107 2019-07-15 ☒ A.M.N. R&S ESH2-Z5 EC 3119 2019-11-30 ☐ A.M.N. R&S ENV 216 EC 3393 2019-07-04 ☐ A.M.N. R&S ENV4200 EC 3558 2019-06-10 Radiated Emission Used Equipment Manufacturer Type Internal no. Due date ☒ Test Receiver R&S ESIB 26 EC 3045 2019-09-12 ☒ Bilog Antenna TESEQ CBL 6112D EC 4206 2019-06-10 AFS42- ☒ Pre-amplifier R&S 00101800-25-S- EC5262 2019-06-10 42 ☒ Horn antenna R&S HF 906 EC 3049 2019-11-17 ☐ Horn antenna ETS 3117 EC 4792-1 2020-01-09 ☒ Horn antenna TOYO HAP18-26W EC 4792-3 2020-07-09 Active loop ☒ Schwarzbeck FMZB1519 EC 5345 2020-03-07 antenna RF test Used Equipment Manufacturer Type Internal no. Due date ☒ PXA Signal Analyzer Keysight N9030A EC 5338 2020-03-05 ☐ Power sensor Agilent U2021XA EC 5338-1 2020-03-05 Vector Signal ☐ Agilent N5182B EC 5175 2020-03-05 Generator ☐ Spectrum analyzer R&S CMW500 EC5944 2019-12-22 MXG Analog Signal ☐ Agilent N5181A EC 5338-2 2020-03-05 Generator ☐ Mobile Test System Litepoint Iqxel EC 5176 2020-01-08 ☐ Test Receiver R&S ESCI 7 EC 4501 2019-09-12 Tet Site Used Equipment Manufacturer Type Internal no. Due date ☒ Shielded room Zhongyu - EC 2838 2020-01-14 ☐ Shielded room Zhongyu - EC 2839 2020-01-14 Semi-anechoic Albatross ☒ - EC 3048 2019-07-31 chamber project Fully-anechoic Albatross ☐ - EC 3047 2019-07-31 chamber project Additional instrument Used Equipment Manufacturer Type Internal no. Due date Therom- ZJ1-2A S.M.I.F. EC 3783 ☒ 2020-02-28 Hygrograph Therom- ZJ1-2A S.M.I.F. EC 2122 ☐ 2020-03-11 Hygrograph TTRFFCCDFS-01_V1 © 2018 Intertek Page 9 of 22

Report No. 190400328SHA-003 TEST REPORT Therom- ZJ1-2A S.M.I.F. ☒ EC 5198 2020-01-18 Hygrograph Therom- ZJ1-2A S.M.I.F. ☒ EC 3326 2020-03-28 Hygrograph Shanghai ☐ Pressure meter YM3 EC 3320 2019-07-01 Mengde Test Software Manufacturer Function Pulse Building Agilent Radar Signal Generation DFS Tool Agilent Software DFS Test Software TTRFFCCDFS-01_V1 © 2018 Intertek Page 10 of 22

Report No. 190400328SHA-003 TEST REPORT 3 DFS Detection Thresholds and Radar Test Waveforms Test result: Pass 3.1 Interference Threshold values Maximum Transmit Power Value (see note) ≥ 200 mW -64 dBm < 200 mW -62 dBm Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. 3.2 DFS Response requirement values Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds Channel Move Time 10 seconds See Note 1. 200 milliseconds + an aggregate of 60 milliseconds over Channel Closing Transmission Time remaining 10 second period. See Notes 1 and 2. U-NII Detection Bandwidth Minimum 80% of the 99% power bandwidth See Note 3. Note 1: Channel Move Time and the Channel Closing Transmission Time should be performed with Radar Type 0. The measurement timing begins at the end of the Radar Type 0 burst. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. Note 3: During the U-NII Detection Bandwidth detection test, radar type 0 should be used. For each frequency step the minimum percentage of detection is 90 percent. Measurements are performed with no data traffic. TTRFFCCDFS-01_V1 © 2018 Intertek Page 11 of 22

Report No. 190400328SHA-003 TEST REPORT 3.3 Radar Test Waveforms Minimum Step Step intervals of 0.1 microsecond for Pulse Width, 1 microsecond for PRI, 1 MHz for chirp width and 1 for the number of pulses will be utilized for the random determination of specific test waveforms. 3.4 Test Result Minimum Pulse Minimum Radar PRI Percentage Width Number of Pulses Number of Type (μs) of Successful (μs) Trials Detection 0 1 1428 18 See Note 1 See Note 1 15 unique PRI values randomly selected 1a from the list of 23 PRI values in Note 2 15 unique PRI values Roundup 1 randomly selected 60% 30 {(1/360)*(19*106/PRI)} within the range of 518-3066μsec, with a 1b minimum increment of 1 μsec, excluding PRI values selected in radar type 1a 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 Note 1: Short Pulse Radar Type 0 should be used for the detection bandwidth test, channel move time, and channel closing time tests. TTRFFCCDFS-01_V1 © 2018 Intertek Page 12 of 22

Report No. 190400328SHA-003 TEST REPORT Note 2: Pulse Repetition Intervals Values for Radar Type 1a Pulse Repetition Frequency Pulse Repetition Interval Pulse Repetition Frequency No (Pulses Per Second) (us) 1 1930.5 518 2 1858.7 538 3 1792.1 558 4 1730.1 578 5 1672.2 598 6 1618.1 618 7 1567.4 638 8 1519.8 658 9 1474.9 678 10 1432.7 698 11 1392.8 718 12 1355 738 13 1319.3 758 14 1285.3 778 15 1253.1 798 16 1222.5 818 17 1193.3 838 18 1165.6 858 19 1139 878 20 1113.6 898 21 1089.3 918 22 1066.1 938 23 326.2 3066 A minimum of 30 unique waveforms are required for each of the Short Pulse Radar Types 2 through 4. If more than 30 waveforms are used for Short Pulse Radar Types 2 through 4, then each additional waveform must also be unique and not repeated from the previous waveforms. If more than 30 waveforms are used for Short Pulse Radar Type 1, then each additional waveform is generated with Test B and must also be unique and not repeated from the previous waveforms in Tests A or B. For example, if in Short Pulse Radar Type 1 Test B a PRI of 3066us is selected, the number of pulses would be TTRFFCCDFS-01_V1 © 2018 Intertek Page 13 of 22

Report No. 190400328SHA-003 TEST REPORT 3.5 Long Pulse Radar Test Waveform Minimum Chirp Number Minimum Pulse Width PRI PRI Percentage of Radar Type Width of Pulses Number of (μs) (μs) (μsec) Successful (MHz) per Burst Trials Detection 1000- 5 50-100 5-20 1-3 8-20 80% 30 2000 The parameters for this waveform are randomly chosen. Thirty unique waveforms are required for the Long Pulse Radar Type waveforms. If more than 30 waveforms are used for the Long Pulse Radar Type waveforms, then each additional waveform must also be unique and not repeated from the previous waveforms. Each waveform is defined as follows: 1) The transmission period for the Long Pulse Radar test signal is 12 seconds. 2) There are a total of 8 to 20 Bursts in the 12 second period, with the number of Bursts being randomly chosen. This number is Burst_Count. 3) Each Burst consists of 1 to 3 pulses, with the number of pulses being randomly chosen. Each Burst within the 12 second sequence may have a different number of pulses. 4) The pulse width is between 50 and 100 microseconds, with the pulse width being randomly chosen. Each pulse within a Burst will have the same pulse width. Pulses in different Bursts may have different pulse widths. 5) Each pulse has a linear frequency modulated chirp between 5 and 20 MHz, with the chirp width being randomly chosen. Each pulse within a Burst will have the same chirp width. Pulses in different Bursts may have different chirp widths. The chirp is centered on the pulse. For example, with a radar frequency of 5300 MHz and a 20 MHz chirped signal, the chirp starts at 5290 MHz and ends at 5310 MHz. 6) If more than one pulse is present in a Burst, the time between the pulses will be between 1000 and 2000 microseconds, with the time being randomly chosen. If three pulses are present in a Burst, the random time interval between the first and second pulses is chosen independently of the random time interval between the second and third pulses. 7) The 12 second transmission period is divided into even intervals. The number of intervals is equal to Burst_Count. Each interval is of length (12,000,000 / Burst_Count) microseconds. Each interval contains one Burst. The start time for the Burst, relative to the beginning of the interval, is between 1 and [(12,000,000 / Burst_Count) – (Total Burst Length) + (One Random PRI Interval)] microseconds, with the start time being randomly chosen. The step interval for the start time is 1 microsecond. The start time for each Burst is chosen randomly. TTRFFCCDFS-01_V1 © 2018 Intertek Page 14 of 22

Report No. 190400328SHA-003 TEST REPORT A representative example of a Long Pulse Radar Type waveform: 1) The total test waveform length is 12 seconds. 2) Eight (8) Bursts are randomly generated for the Burst_Count. 3) Burst 1 has 2 randomly generated pulses. 4) The pulse width (for both pulses) is randomly selected to be 75 microseconds. 5) The PRI is randomly selected to be at 1213 microseconds. 6) Bursts 2 through 8 are generated using steps 3 – 5. 7) Each Burst is contained in even intervals of 1,500,000 microseconds. The starting location for Pulse 1, Burst 1 is randomly generated (1 to 1,500,000 minus the total Burst 1 length + 1 random PRI interval) at the 325,001 microsecond step. Bursts 2 through 8 randomly fall in successive 1,500,000 microsecond intervals (i.e. Burst 2 falls in the 1,500,001 – 3,000,000 microsecond range). 3.6 Frequency Hopping Radar Test Waveform Hopping Minimum Pulse Pulses Hopping Minimum Radar PRI Sequence Percentage of Width per Rate Number of Type (μs) Length Successful (μs) Hop (kHz) Trials (msec) Detection 6 1 333 9 0.333 300 70% 30 For the Frequency Hopping Radar Type, the same Burst parameters are used for each waveform. The hopping sequence is different for each waveform and a 100-length segment is selected from the hopping sequence defined by the following algorithm: The first frequency in a hopping sequence is selected randomly from the group of 475 integer frequencies from 5250 – 5724MHz. Next, the frequency that was just chosen is removed from the group and a frequency is randomly selected from the remaining 474 frequencies in the group. This process continues until all 475 frequencies are chosen for the set. For selection of a random frequency, the frequencies remaining within the group are always treated as equally likely. Note: If a segment does not contain at least 1 frequency within the U-NII Detection Bandwidth of the UUT, then that segment is not used. TTRFFCCDFS-01_V1 © 2018 Intertek Page 15 of 22

Report No. 190400328SHA-003 TEST REPORT 3.7 Calibration Setup Radiated Method Monitor Antenna Radar Antenna Radar Generator Spectrum Analyzer Conducted Method Spectrum 50Ω Terminator Analyzer Combiner Combiner 50Ω Terminator Radar Generator TTRFFCCDFS-01_V1 © 2018 Intertek Page 16 of 22

Report No. 190400328SHA-003 TEST REPORT 3.8 Radar Waveform Calibration Procedure The Interference Radar Detection Threshold Level is -64dBm or -62dBm + 0 [dBi] + 1 dB that had been taken into account the output power range and antenna gain. The above equipment setup was used to calibrate the conducted Radar Waveform. A vector signal generator was utilized to establish the test signal level for each radar type. During this process there were replace 50ohm terminal form Master and Client device and no transmissions by either the Master or Client Device. The spectrum analyzer was switched to the zero span (Time Domain) at the frequency of the Radar Waveform generator. Peak detection was used. The spectrum analyzer resolution bandwidth (RBW) and video bandwidth (VBW) were set to at least 3MHz. The vector signal generator amplitude was set so that the power level measured at the spectrum analyzer was -64dBm or -62dBm + 0 [dBi] + 1 dB. Capture the spectrum analyzer plots on short pulse radar types, long pulse radar type and hopping radar waveform. Central Frequency of Calibration: Bandwidth 20MHz: 5500MHz Bandwidth 40MHz: 5510MHz Bandwidth 80MHz: 5530MHz TTRFFCCDFS-01_V1 © 2018 Intertek Page 17 of 22

Report No. 190400328SHA-003 TEST REPORT 3.9 Radar Waveform Calibration Result 5500MHz, Radar 0 5510MHz, Radar 0 TTRFFCCDFS-01_V1 © 2018 Intertek Page 18 of 22

Report No. 190400328SHA-003 TEST REPORT 5530MHz, Radar 0 TTRFFCCDFS-01_V1 © 2018 Intertek Page 19 of 22

Report No. 190400328SHA-003 TEST REPORT 4 In-Service Monitoring for Channel Move Time, Channel Closing Transmission Time and Non-Occupancy Period These tests define how the following DFS parameters are verified during In-Service Monitoring; Channel Closing Transmission Time, Channel Move Time, and Non-Occupancy Period. The steps below define the procedure to determine the above mention parameters when a radar Burst with a level equal to the DFS Detection Threshold + 1dB (-63dBm) is generated on the Operating Channel of the U-NII device. A U-NII device operating as a Client Device will associate with the UUT (Master) at 5530MHz. Stream the MPEG test file from the Master Device to the Client Device on the selected Channel for the entire period of the test. At time T0 the Radar Waveform generator sends a Burst of pulses for each of the radar types at - 63dBm. Observe the transmissions of the UUT at the end of the radar Burst on the Operating Channel for duration greater than 10 seconds. Measure and record the transmissions from the UUT during the observation time (Channel Move Time). Compare the Channel Move Time and Channel Closing Transmission Time results to the limits defined in the DFS Response requirement values table. Type 0 radar was used for these tests. TTRFFCCDFS-01_V1 © 2018 Intertek Page 20 of 22

Report No. 190400328SHA-003 TEST REPORT 4.1 Channel Move Time, Channel Closing Transmission Time 5530MHz Test Item Limit Results Channel Move Time 10 s Pass Channel Closing 200ms + an aggregate of 60ms over Pass Transmission Time remaining 10 second period. TTRFFCCDFS-01_V1 © 2018 Intertek Page 21 of 22

Report No. 190400328SHA-003 TEST REPORT 4.2 Non-Occupancy Period 5530MHz Test Item Limit Results Non-Occupancy Period 30 minutes Pass *************************************** END *************************************** TTRFFCCDFS-01_V1 © 2018 Intertek Page 22 of 22


Document Created: 2019-05-23 09:54:01
Document Modified: 2019-05-23 09:54:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC