User Manual_Rev 1

FCC ID: 2AJVQ-7618BUC

Users Manual

Download: PDF
FCCID_4223340

Qingdao Intelligent & Precise Electronics Co., Ltd ZDGF7618BU-C User Manual Product Name：IEEE 802.11 a/b/g/n/ac 2.4GHz+5GHz 2T2R USB Module Model ：ZDGF7618BU-C

1. Introduction Thank you for using the Wi-Fi module product provided by Qingdao Intelligent &Precise Electronics Co., Ltd. Before use, please read this user manual carefully. Please follow the technical specifications when using the module in your design and develop activities. Qingdao Intelligent &Precise Electronics Co., Ltd has the right to change the contents of this manual in accordance with the needs of the technical development. FCC & IC application: This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. MPE Requirements To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon àce que la population ne puisse y être exposée àune distance de moin de 20 cm. Installer les antennes de facon àce que le personnel ne puisse approcher à20 cm ou moins de la position centrale de l’ antenne. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement. 1

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; les dispositifs fonctionnant dans la bande de 5 150 à5 250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; Region Selection Limited by local law regulations, version for North America does not have region selection option. Label Host labeling requirement:”Contains transmitter module FCC ID: 2AJVQ-7618BUC”. Host labeling requirement:”Contains transmitter module IC: 22470-7618BUC”. 2．Product Information 2.1 Product Information ZDGF7618BU-C Wi-Fi USB module is a wireless signal module device work at 2.4GHz(2.400 ~ 2.4835GHz)/5GHz (5.150 ~ 5.85GHz) .ZDGF7618BU-C comply with IEEE 802.11a、802.11b、802.11 g 、802.11 n and 802.11 ac standard. It support up to 867Mbps physical layer transmitting rate. ZDGF7618BU-C support USB 2.0, which has up to 480Mbps data rate. ZDGF7618BU-C has 2T2R structure，has two onboard PIFA Antenna. It could provide stable wireless link with high throughput. ZDGF7618BU-C is a wireless Wi-Fi signal module. It could transmit and receive Wi-Fi wireless signal device without radar detection It is widely used to multi-media device, such as smart TV.Equipped with ZDGF7618BU-C, a smart TV could access to Wireless Local Network, which is also called WLAN or WIFI network. ZDGF7618BU-C helps multi-media device achieve to send & receive data package in a wireless way. 2.2 Feature ●IEEE standard：IEEE 802.11a/b/g/n/ac client device without radar detection ●operating Frequency 2.4GHz/5 GHz ●support up to 867Mbps ● 2T2R mode ●Support 20MHz, 40MHz, 80MHz in 5GHz band, and 20MHz, 40MHz band width in 2.4GHz band. ●support USB 2.0 high data rate mode,10-pin interface ●low power consumption ●support Wi-Fi direct link ●support WFA/ WPA/WPA2 /WPS2.0/WAPI security ●RoH ●MAC /baseband/RF： MT7618BU 2

3. Product Specification 3.1 Parameter WLAN Standard IEEE802.11a/b/g/n/ac Data Interface USB2.0 WIFI: 802.11b:CCK, DQPSK, DBPSK Modulation Mode 802.11a, 802.11g:64QAM, 16QAM, QPSK, BPSK 802.11n:64QAM, 16QAM, QPSK, BPSK 802.11ac:256QAM, 64QAM, 16QAM, QPSK, BPSK 2400-2483.5MHz for US and Canada 5150-5350MHz for US and Canada Working Frequency 5470-5725MHz for US and Canada 5725-5850MHz for US and Canada 11b @ 11Mbps: (Max.) : -84dBm , (Typical) : -87dBm (PER<8%) 11g @ 54Mbps: (Max.) : -69dBm , (Typical) : -77dBm (PER<10%) 11n @ MCS7 (2.4g HT20): (Max.) : -67dBm , (Typical) : -73dBm (PER<10%) 11n @ MCS7 (2.4g HT40): (Max.) : -64dBm , (Typical) : -68dBm (PER<10%) Receiver Sensitivity 11a @ 54Mbps: (5g) : -69dBm , (Typical) : -77dBm (PER<10%) 11n @ MCS7 (5g HT20): (Max.) : -67dBm , (Typical) : -73dBm (PER<10%) 11n @ MCS7 (5g HT40): (Max.) : -64dBm , (Typical) : --69dBm (PER<10%) 11ac @ MCS9 (5g HT80): (Max.) : -51dBm , (Typical) : -58dBm (PER<10%) Working Voltage 5V±10% I/O supply voltage 2.4G :Ant0:2.15dBi ,Ant1:2.53dBi Antenna Gain 5G: Ant0:3.44dBi ,Ant1:3.37dBi Antenna type Two onboard PIFA antennas Working Temperature -10~+70℃ Storage Temperature -40~+125℃ 4. Hardware information 4.1 structure dimension：（Unit:mm） PCB Material：FR-4，Surface treatment：OSP. Appearance Dimension（mm）：70（+/- 0.3）×45（+/- 0.3） PCB thickness：1.6mm（+/-0.15mm）. Via：Ф4mm（+/-0.15mm）. Antenna Height：6.0mm（+/-0.15mm）. 4.2 PIN definition No. Definiton 3

1 VCC 2 VCC 3 GND 4 USBDM 5 空 6 USBDP 7 USBDPWLAN_DEV_WAKE 8 GND 9 WIFI_REG_ON 10 RST 4.3 Block Diagram 5V DC-DC Converter SOT23-5 3.3V 2.4G TX0/RX0 IPD 5G Antenna MCU TX0/RX0 ANT0 MT7618BU QFN 2.4G 40MHz TX1/RX1 XTAL1 Diplexer 5G Antenna TX1/RX1 ANT1 USB 2.0 XP1 Connector BLOCK DIAGRAM 5 EU single contact point Hisense Czech (Manufacture) s.r.o. U Nové Hospody 1164/4, 301 00 Plzeň ,Czech Republic. 6 Manufacture’s postal address No.218,Qianwangang Road, Qingdao Economic & Technological Development Zone,Shandong,China 7 Importer’s name & address The importer is not determined, the importer’s name and address will be declared in this user manual when the importer is determined. 4


Document Created: 2019-04-02 09:13:31
Document Modified: 2019-04-02 09:13:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC