Test Report

FCC ID: 2AJRQME105P

Test Report

Download: PDF
FCCID_3587606

FCC RADIO TEST REPORT FCC ID: 2AJRQME105P Product： Wireless Charger Trade Name： Maxeye Model Name： ME105P Serial Model： ME105A, ME105B, ME105C, ME105D Report No.： POCE17091932BRF Prepared for Maxeye Smart Technologies Co., Ltd. Room 6008, Chuangxingda Buiding, Xinan, Baoan, Shenzhen, China Prepared by Shenzhen POCE Technology Co.,Ltd. Room 502, Bldg. 1, Xinghua Garden, Baoan Road Xixiang, Baoan District,Shenzhen, China

Page 2 of 22 Report No.: POCE17091932BRF TEST RESULT CERTIFICATION Applicant’s name ................. : Maxeye Smart Technologies Co., Ltd. Address ................................. : Room 6008, Chuangxingda Buiding, Xinan, Baoan, Shenzhen, China Manufacture's Name............ : Maxeye Smart Technologies Co., Ltd. Address ................................. : Room 6008, Chuangxingda Buiding, Xinan, Baoan, Shenzhen, China Product description Product name ........................... : Wireless Charger Model and/or type reference : ME105P, ME105A, ME105B, ME105C, ME105D Standards ............................. : 15.209 Test procedure .............................. ANSI C63.4: 2014 This device described above has been tested by POCE, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of POCE, this document may be altered or revised by POCE, personal only, and shall be noted in the revision of the document. Date of Test ............................................ : Date (s) of performance of tests ............. : 3 Jul. 2017 ~11 Jul. 2017 Date of Issue ........................................... : 11 Jul. 2017 Test Result ............................................... : Pass Testing Engineer : (Jerry Lin) Technical Manager : (Jimmy Yao) Authorized Signatory : (Terry Yang)

Page 3 of 22 Report No.: POCE17091932BRF Table of Contents Page 1 . TEST SUMMARY 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 DESCRIPTION OF TEST SETUP 8 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 9 2.5 MEASUREMENT INSTRUMENTS LIST 10 3 . EMC EMISSION TEST 11 3.1 CONDUCTED EMISSION MEASUREMENT 11 3.1.1 POWER LINE CONDUCTED EMISSION 11 3.1.2 TEST PROCEDURE 12 3.1.3 TEST SETUP 12 3.1.4 EUT OPERATING CONDITIONS 12 3.1.5 TEST RESULTS 13 3.2 RADIATED EMISSION MEASUREMENT 15 3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT 15 3.2.2 TEST PROCEDURE 15 3.2.3 TEST SETUP 17 3.2.4 EUT OPERATING CONDITIONS 17 3.2.5 TEST RESULTS(Blow 30MHZ) 19 3.2.6 TEST RESULTS( 30MHZ-1GHZ) 20 4 . ANTENNA REQUIREMENT 22 4.1 STANDARD REQUIREMENT 22 4.2 EUT ANTENNA 22

Page 4 of 22 Report No.: POCE17091932BRF 1. TEST SUMMARY Test procedures according to the technical standards: EMC Emission Standard Test Item Limit Judgment Remark FCC Part 15.207 Conducted Emission Class B PASS FCC Part 15.209 Radiated Emission Class B PASS 15.203 Antenna Requirement -- PASS

Page 5 of 22 Report No.: POCE17091932BRF 1.1 TEST FACILITY Shenzhen POCE Technology Co.,Ltd. Add. : Room 502, Bldg. 1, Xinghua Garden, Baoan Road Xixiang, Baoan District, Shenzhen, China FCC Registered No.: 222278 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 A. Conducted Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE POCE01 ANSI 150 KHz ~ 30MHz 3.2 B. Radiated Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE POCE01 ANSI 30MHz ~ 1000MHz 4.7 1GHz ~6GHz 5.0

Page 6 of 22 Report No.: POCE17091932BRF 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Wireless Charger Brand Name Maxeye Model Name. ME105P Serial No ME105A, ME105B, ME105C, ME105D All the model are the same circuit and RF module, Model Difference except model names. Power Supply DC 5V from USB port Operation frequency 110-205KHz Antenna Type Loop antenna

Page 7 of 22 Report No.: POCE17091932BRF 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 Charging Mode For Conducted Test Final Test Mode Description Mode 1 Charging Mode For Radiated Test Final Test Mode Description Mode 1 Charging Mode

Page 8 of 22 Report No.: POCE17091932BRF 2.3 DESCRIPTION OF TEST SETUP E1 E2

Page 9 of 22 Report No.: POCE17091932BRF 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Series No. Note E-1 Wireless Charger Maxeye ME105P ME105A, ME105B, EUT ME105C, ME105D E-2 GALAXY S7 SAMSUNG G9350 N/A Item Shielded Type Ferrite Core Length Note Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column.

Page 10 of 22 Report No.: POCE17091932BRF 2.5 MEASUREMENT INSTRUMENTS LIST Radiation Test equipment Kind of Last Calibrated Calibratio Item Manufacturer Type No. Serial No. Equipment calibration until n period 1 Spectrum Agilent E4407B MY4510804 2016.09.06 2017.09.05 1 year Analyzer 0 2 Test Receiver R&S ESPI 101318 2016.09.07 2017.09.06 1 year 3 Bilog Antenna TESEQ CBL6111D 31216 2016.09.06 2017.09.05 1 year 4 50Ω Coaxial Anritsu MP59B 620026441 2016.09.07 2017.09.06 1 year Switch 6 Spectrum 5 ADVANTEST R3132 150900201 2016.09.07 2017.09.06 1 year Analyzer 6 Horn Antenna EM EM-AH-101 2011071402 2016.09.06 2017.09.05 1 year 80 7 Horn Ant Schwarzbeck BBHA 9170 9170-181 2016.09.06 2017.09.05 1 year 8 Amplifier EM EM-30180 060538 2016.12.22 2017.12.21 1 year 9 Loop Antenna ARA PLA-1030/B 1029 2016.09.08 2017.09.07 1 year 10 Power Meter R&S NRVS 100696 2016.09.06 2017.09.05 1 year 11 Power R&S URV5-Z4 0395.1619. 2016.09.06 2017.09.05 1 year Sensor 05 Conduction Test equipment Kind of Manufactu Last Calibrated Calibration Item Type No. Serial No. Equipment rer calibration until period 1 Test Receiver R&S ESCI 101160 2016.09.06 2017.09.05 1 year 2 LISN R&S ENV216 101313 2016.08.24 2017.08.23 1 year 3 LISN EMCO 3816/2 00042990 2016.08.24 2017.08.23 1 year 50Ω Coaxial 4 Anritsu MP59B 6200264417 2016.09.07 2017.09.06 1 year Switch 5 Passive Voltage R&S ESH2-Z3 100196 2016.09.07 2017.09.06 1 year Probe 6 Absorbing clamp R&S MOS-21 100423 2016.09.08 2017.09.07 1 year

Page 11 of 22 Report No.: POCE17091932BRF 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION (Frequency Range 150KHz-30MHz) Class B (dBuV) FREQUENCY (MHz) Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * 0.50 -5.0 56.00 46.00 5.0 -30.0 60.00 50.00 Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 12 of 22 Report No.: POCE17091932BRF 3.1.2 TEST PROCEDURE a. The EUT was placed 0.4 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.1.3 TEST SETUP 3.1.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

Page 13 of 22 Report No.: POCE17091932BRF 3.1.5 TEST RESULTS EUT： Wireless Charger Model Name. ： ME105P Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Phase : L Test Voltage ： AC120V/60Hz Test Mode： Charging Frequency Meter Reading Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV) (dBμV) (dB) 0.19 32.86 10.4 43.26 64.03 -20.77 QP 0.194 21.54 10.41 31.95 53.86 -21.91 AVG 0.6058 19.92 10.4 30.32 46 -15.68 AVG 0.7378 33.61 10.41 44.02 56 -11.98 QP 5.0579 30.91 10.67 41.58 60 -18.42 QP 5.7458 15.89 10.67 26.56 50 -23.44 AVG Remark: 1. All readings are Quasi-Peak and Average values. 2. Factor = Insertion Loss + Cable Loss.

Page 14 of 22 Report No.: POCE17091932BRF EUT： Wireless Charger Model Name. ： ME105P Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Phase : N Test Voltage ： AC120V/60Hz Test Mode： Charging Frequency Meter Reading Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV) (dBμV) (dB) 0.2099 28.01 10.44 38.45 63.21 -24.76 QP 0.2859 21.65 10.43 32.08 50.64 -18.56 AVG 0.626 31.99 10.41 42.4 56 -13.6 QP 0.626 21.76 10.41 32.17 46 -13.83 AVG 3.322 15.15 10.53 25.68 46 -20.32 AVG 3.5019 28.89 10.6 39.49 56 -16.51 QP Remark: 1. All readings are Quasi-Peak and Average values. 2. Factor = Insertion Loss + Cable Loss.

Page 15 of 22 Report No.: POCE17091932BRF 3.2 RADIATED EMISSION MEASUREMENT 3.2.1 RADIATED EMISSIONLIMITS(FREQUENCY RANGE 9KHZ-1000MHZ) 20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed.(unintentional radiator) Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 The following table is the setting of the receiver Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RB / VB (emission in restricted 1 MHz / 1 MHz for Peak, 1 MHz / 10Hz for Average band) Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~150kHz / RB 200Hz for QP Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP 3.2.2 TEST PROCEDURE a. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1GHz, any suitable measuring distance may be used. b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. c. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured, above 1G Average detector mode will be instead.

Page 16 of 24 Report No.: POCE17091932BRF e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP(AV) Limits and then no additional QP Mode measurement performed. f. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.2.3 DEVIATION FROM TEST STANDARD No deviation

Page 17 of 22 Report No.: POCE17091932BRF 3.2.3 TEST SETUP （A）Radiated Emission Test-Up Frequency Below 30MHz (B) Radiated Emission Test Set-Up Frequency Below 1 GHz

Page 18 of 24 Report No.: POCE17091932BRF (C) Radiated Emission Test Set-Up Frequency Above 1GHz 3.2.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

Page 19 of 22 Report No.: POCE17091932BRF 3.2.5 TEST RESULTS(Blow 30MHZ) Note: pp is Fundamental Field strength.

Page 20 of 22 Report No.: POCE17091932BRF 3.2.6 TEST RESULTS( 30MHZ-1GHZ) EUT： Wireless Charger Model Name ： ME105P Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： AC120V Test Mode ： Charging Polarization : Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 199.2855 26.88 8.71 35.59 43.5 -7.91 QP 331.3546 24.23 14.97 39.2 46 -6.8 QP 394.8543 23.77 17.03 40.8 46 -5.2 QP 531.9633 18.85 19.76 38.61 46 -7.39 QP 793.3958 16.51 23.91 40.42 46 -5.58 QP Remark: 1. Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Page 21 of 22 Report No.: POCE17091932BRF EUT： Wireless Charger Model Name ： ME105P Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： AC120V Test Mode ： Charging Polarization : Vertical Frequency Meter Reading Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 199.2855 30.12 8.71 38.83 43.5 -4.67 QP 392.0951 25.41 16.93 42.34 46 -3.66 QP 531.9633 20.35 19.76 40.11 46 -5.89 QP 590.9737 14.71 20.79 35.5 46 -10.5 QP Remark: 1. Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Page 22 of 22 Report No.: POCE17091932BRF 4. ANTENNA REQUIREMENT 4.1 STANDARD REQUIREMENT 15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 4.2 EUT ANTENNA The EUT antenna is a Loop Antenna. It comply with the standard requirement. Loop antenna

Page 23 of 22 Report No.: POCE17091932BRF RADIATED SPURIOUS EMISSION

Page 24 of 22 Report No.: POCE17091932BRF CONDUCTED EMISSION TEST


Document Created: 2017-09-20 20:11:23
Document Modified: 2017-09-20 20:11:23
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC