Test Report

FCC ID: 2AJQ7-LGO-NCB-RCK

Test Report

Download: PDF
FCCID_3150413

- Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 Fax: +86-755-26636041 FCC PART 15 SUBPART C TEST REPORT Report Reference No.: CTL1609053410-WF Compiled by: Happy Guo ( position+printed name+signature) (File administrators) Tested by: Nice Nong ( position+printed name+signature) (Test Engineer) Approved by: Tracy Qi ( position+printed name+signature) (Manager) IJOY LOGO NECK BLUETOOTH Product Name...............................: HEADPHONE LGO-NCB-RCK, LGO-NCB-DOV, LGO-NCB-WAT, LGO-NCB-TRE, Model/Type reference..................: LGO-NCB-PLS, LGO-NCB-RED, LGO-NCB-PPL, LGO-NCB-GRN Trade Mark....................................: IJOY FCC ID...........................................: 2AJQ7-LGO-NCB-RCK Applicant’s name.........................: QUEST USA CORP Address of applicant...................: 495 Flatbush Ave, Brooklyn, NY 11225, USA Test Firm.......................................: Shenzhen CTL Testing Technology Co., Ltd. Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan Address of Test Firm...................: District, Shenzhen, China 518055 Test specification.........................: FCC Part 15.249: Operation within the bands 920-928 MHz, 2400- Standard........................................: 2483.5 MHz, 5725-5850 MHz and 24.0 - 24.25 GHz. TRF Originator……………………..: Shenzhen CTL Testing Technology Co., Ltd. Master TRF…………………………: Dated 2011-01 Date of Receipt.............................: Sept. 05, 2016 Date of Test Date..........................: Sept. 05, 2016-Sept. 21, 2016 Data of Issue.................................: Sept. 21, 2016 Result............................................: PASS Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.

V1.0 Page 2 of 29 Report No.: CTL1609053410-WF TEST REPORT Sept. 21, 2016 Test Report No. : CTL1609053410-WF ______________________________________________________________________________________________ Date of issue Equipment under Test : IJOY LOGO NECK BLUETOOTH HEADPHONE Model /Type : LGO-NCB-RCK, LGO-NCB-DOV, LGO-NCB-WAT, LGO-NCB-TRE, LGO-NCB-PLS, LGO-NCB-RED, LGO-NCB-PPL, LGO-NCB-GRN Applicant : QUEST USA CORP Address : 495 Flatbush Ave, Brooklyn, NY 11225, USA Manufacturer : SHENZHEN LEADINGPLUS ELECTRONIC CO., LTD Address : 209/213, Dongxu Building, Minhuan Road, Longhua New District, Shenzhen, China Test Result according to the PASS standards on page 4: The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

V1.0 Page 3 of 29 Report No.: CTL1609053410-WF Contents 1. TEST STANDARDS .................................................................. 4 2. SUMMARY ............................................................................. 5 2.1. Equipment Under Test 5 2.2. Description of the Equipment under Test (EUT) 5 2.3. EUT operation mode 6 2.4. EUT configuration 6 2.5. Related Submittal(s) / Grant (s) 6 2.6. Modifications 6 3. TEST ENVIRONMENT............................................................... 7 3.1. Address of the test laboratory 7 3.2. Test Facility 7 3.3. Environmental conditions 7 3.4. Configuration of Tested System 7 3.5. Statement of the measurement uncertainty 8 3.6. Equipments Used during the Test 9 4. TEST CONDITIONS AND RESULTS ............................................ 10 4.1. Conducted Emissions Test 10 4.2. Transmitter Radiated Unwanted Emissions and Bandedge 13 4.3. Occupied Bandwidth Measurement 19 5. ANTENNA REQUIREMENT ....................................................... 23 6. TEST SETUP PHOTOS OF THE EUT .......................................... 24 7. EXTERNAL AND INTERNAL PHOTOS OF THE EUT ....................... 26

V1.0 Page 4 of 29 Report No.: CTL1609053410-WF 1. TEST STANDARDS The tests were performed according to following standards: FCC Rules Part 15.249: Operation within the bands 902 - 928 MHz, 2400 - 2483.5 MHz, 5725 - 5875 MHz, and 24.0 - 24.25 GHz. ANSI C63.10-2013 ANSI C63.4-2014

V1.0 Page 5 of 29 Report No.: CTL1609053410-WF 2. SUMMARY 2.1. Equipment Under Test Power supply system utilised Power supply voltage : o 120V / 60 Hz o 115V / 60Hz o 12 V DC o 24 V DC ● Other (specified in blank below) DC 3.7V from battery 2.2. Description of the Equipment under Test (EUT) The EUT (IJOY LOGO NECK BLUETOOTH HEADPHONE) support Bluetooth function. Name of EUT IJOY LOGO NECK BLUETOOTH HEADPHONE Model Number LGO-NCB-RCK Antenna Type PCB Antenna BT Operation frequency 2402MHz-2480MHz BT Modulation Type GFSK,8DPSK,π/4DQPSK(BT V4.1) Bluetooth BT V4.1 Antenna Gain 0dBi Channel List: Frequency Frequency Frequency Channel Channel Channel (MHz) (MHz) (MHz) 00 2402 27 2429 54 2456 01 2403 28 2430 55 2457 02 2404 29 2431 56 2458 03 2405 30 2432 57 2459 04 2406 31 2433 58 2460 05 2407 32 2434 59 2461 06 2408 33 2435 60 2462 07 2409 34 2436 61 2463 08 2410 35 2437 62 2464 09 2411 36 2438 63 2465 10 2412 37 2439 64 2466 11 2413 38 2440 65 2467 12 2414 39 2441 66 2468 13 2415 40 2442 67 2469 14 2416 41 2443 68 2470 15 2417 42 2444 69 2471 16 2418 43 2445 70 2472 17 2419 44 2446 71 2473 18 2420 45 2447 72 2474 19 2421 46 2448 73 2475 20 2422 47 2449 74 2476 21 2423 48 2450 75 2477 22 2424 49 2451 76 2478 23 2425 50 2452 77 2479 24 2426 51 2453 78 2480 25 2427 52 2454 26 2428 53 2455 For more details, refer to the user’s manual of the EUT. Serial number: Prototype

V1.0 Page 6 of 29 Report No.: CTL1609053410-WF 2.3. EUT operation mode Test Mode(TM) Description Remark TM1 Bottom Channel Transmitting / TM2 Middle Channel Transmitting / TM3 Top Channel Transmitting / TM4 Charging and keeping TX power by battery The field strength of radiation emission was measured in the following position: EUT stand-up position (Y axis), lie-down position (X, Z axis). The following data show only with the worst case setup. The worst case of X axis was reported. Based on client request, all normal using modes of the normal function were tested but only the worst test data of the worst mode is reported by this report. Remark: GFSK,8DPSK,π/4DQPSK mode all have been tested , only the worst case mode GFSK(1Mbps) is reported for conducted and radiated emission test. 2.4. EUT configuration The following peripheral devices and interface cables were connected during the measurement: o - supplied by the manufacturer ● - supplied by the lab ● Notebook PC (FCC DOC approved) Manufacturer: DELL Model No.: PP18L 2.5. Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: 2AJQ7-LGO-NCB-RCK filing to comply with Section 15.249 of the FCC Part 15, Subpart C Rules. 2.6. Modifications No modifications were implemented to meet testing criteria.

V1.0 Page 7 of 29 Report No.: CTL1609053410-WF 3. TEST ENVIRONMENT 3.1. Address of the test laboratory Shenzhen CTL Testing Technology Co., Ltd. Floor 1-A, Baisha Technology Park, No. 3011, Shahexi Road, Nanshan, Shenzhen 518055 China There is one 3m semi-anechoic chamber and two line conducted labs for final test. The Test Sites meet the requirements in documents ANSI C63.4 and CISPR 22/EN 55022 requirements. 3.2. Test Facility The test facility is recognized, certified, or accredited by the following organizations: IC Registration No.: 9618B The 3m alternate test site of Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered by Certification and Engineer Bureau of Industry Canada for the performance of with Registration No.: 9618B on November 13, 2013. FCC-Registration No.: 970318 Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration 970318, December 19, 2013. 3.3. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15-35 ° C Humidity: 30-60 % Atmospheric pressure: 950-1050mbar 3.4. Configuration of Tested System Fig. 2-1 Configuration of Tested System EUT

V1.0 Page 8 of 29 Report No.: CTL1609053410-WF 3.5. Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to CISPR 16 - 4 „Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements“ and is documented in the Shenzhen CTL Testing Technology Co., Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for CTL laboratory is reported: Test Range Measurement Notes Uncertainty Radiated Emission 30~1000MHz 4.10dB (1) Radiated Emission 1~26.5GHz 4.32dB (1) Conducted Disturbance 0.15~30MHz 3.20dB (1) (1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

V1.0 Page 9 of 29 Report No.: CTL1609053410-WF 3.6. Equipments Used during the Test Calibration Calibration Test Equipment Manufacturer Model No. Serial No. Date Due Date ULTRA-ROADBAND Sunol Sciences JB1 A061713 2016/06/02 2017/06/01 ANTENNA Corp. EMI Test Receiver R&S ESCI 103710 2016/06/02 2017/06/01 Spectrum Analyzer Agilent E4407B MY41440676 2016/05/21 2017/05/20 Controller Controller EM Electronics N/A 2016/05/21 2017/05/20 EM 1000 Sunol Sciences Horn Antenna DRH-118 A062013 2016/05/19 2017/05/18 Corp. Active Loop Antenna Daze ZN30900A N/A 2016/05/19 2017/05/18 LISN R&S ENV216 3560.6550.12 2016/06/02 2017/06/01 LISN R&S ESH2-Z5 860014/010 2016/06/02 2017/06/01 F-071115- ISN FCC 11229 2016/05/19 2017/05/18 1057-1-09 Amplifier Agilent 8349B 3008A02306 2016/05/19 2017/05/18 Amplifier Agilent 8447D 2944A10176 2016/05/19 2017/05/18 Transient Limiter SCHWARZCECK VTSD 9561F 9666 2016/06/02 2017/06/01 Radio Communication R&S CMU200 115419 2016/05/22 2017/05/21 Tester Temperature/Humidity Gangxing CTH-608 02 2016/05/20 2017/05/19 Meter SIGNAL Agilent E4421B US40051744 2016/05/20 2017/05/19 GENERATOR Power Meter Agilent U2531A TW53323507 2016/05/21 2017/05/20 Power Sensor Agilent U2021XA MY5365004 2016/05/21 2017/05/20 Climate Chamber ESPEC EL-10KA A20120523 2016/05/20 2017/05/19 9SH10- High-Pass Filter K&L 2700/X12750 N/A 2016/05/20 2017/05/19 -O/O 41H10- High-Pass Filter K&L 1375/U12750 N/A 2016/05/20 2017/05/19 -O/O RF Cable HUBER+SUHNER RG214 N/A 2016/05/20 2017/05/19 Note:The temporary antenna connector is soldered on the PCB board in order to perform conducted tests and this temporary antenna connector is listed in the equipment list.

V1.0 Page 10 of 29 Report No.: CTL1609053410-WF 4. TEST CONDITIONS AND RESULTS 4.1. Conducted Emissions Test TEST CONFIGURATION TEST PROCEDURE 1 The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. The EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10. 2 Support equipment, if needed, was placed as per ANSI C63.10. 3 All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4 If a EUT received DC power from the USB Port of Notebook PC, the PC’s adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5 All support equipments received AC power from a second LISN, if any. 6 The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7 Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 8 During the above scans, the emissions were maximized by cable manipulation. The RBW/VBW for 150KHz to 30MHz: 9KHz

V1.0 Page 11 of 29 Report No.: CTL1609053410-WF CONDUCTED POWER LINE EMISSION LIMIT For unintentional device, according to § 15.207(a) Line Conducted Emission Limits is as following： Maximum RF Line Voltage (dBμV) Frequency (MHz) CLASS A CLASS B Q.P. Ave. Q.P. Ave. 0.15 - 0.50 79 66 66-56* 56-46* 0.50 - 5.00 73 60 56 46 5.00 - 30.0 73 60 60 50 * Decreasing linearly with the logarithm of the frequency For intentional device, according to §15.207(a) Line Conducted Emission Limit is same as above table. TEST RESULTS

SCAN TABLE: "Voltage (9K—30M)FIN® Short Description: 150R—30M voltage Level dBav) Frequency (ri] x x xurs cmmucosossss in MEASUREMENT RESULT: "CTL160908222_fin" /9/2016 2:329M Erequency Level Transd Limit Margin Detector Line PB mz aspy as amuy as 0.178000 43.10 10.2 65 2i.s ge w cxp 0.182000 44.00 10.2 64 20.4 gr w cxp 0.234000 36.70 10.2 62 2s.6 ge w cxp 0.266000 39.20 10.2 61 22.0 gP N cND 1.682000 22. 60 10.3 se 22.4 on w cxp 2.006000 27.50 10.4 se 28.5 ge w cxp MEASUREMENT RESULT: "CTL160908222_fin2" s/s/z016 2:329m Erequency Level Transd Limit Margin Detector Line PB mz aspy as amuy as 0.28e000 32.80 10.2 s1 i7.8. ay w cxp 1.376000 26.20 10.3 46 10.8 ay w cxp 1.664000 26.10 10.3 46 10.0° ay w cxp 1.742000 29.40 10.3 46 16.6 ay N cNiD 1.826000 27.50 10.3 46 18.5 ay w cxp 2.326000 27.70 10.4 46 18.3 ay w cxp

V1.0 Page 13 of 29 Report No.: CTL1609053410-WF 4.2. Transmitter Radiated Unwanted Emissions and Bandedge TEST CONFIGURATION (A) Radiated Emission Test Set-Up, Frequency Below 30MHz Turntable 3m EUT Test 0.8 m Receiver Ground Plane Coaxial Cable (B) Radiated Emission Test Set-Up, Frequency below 1000MHz 3m Turntable 1m to 4m EUT Test Receiver 0.8m Ground Plane Coaxial Cable (C) Radiated Emission Test Set-Up, Frequency above 1000MHz

V1.0 Page 14 of 29 Report No.: CTL1609053410-WF FIELD STRENGTH CALCULATION The field strength is calculated by adding the Antenna Factor and Cable Factor and subtracting the Amplifier Gain and Duty Cycle Correction Factor(if any) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CL - AG Where FS = Field Strength CL = Cable Attenuation Factor (Cable Loss) RA = Reading Amplitude AG = Amplifier Gain AF = Antenna Factor RADIATION LIMIT For unintentional device, according to § 15.209(a), except for Class A digital devices, the field strength of radiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the following values： Frequency Distance Radiated Radiated (MHz) (Meters) (dBμV/m) (μV/m) 30-88 3 40.0 100 88-216 3 43.5 150 216-960 3 46.0 200 Above 960 3 54.0 500 For intentional device, according to § 15.209(a), the general requirement of field strength of radiated emissions from intentional radiators at a distance of 3 meters shall not exceed the above table. TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane below 1GHz and 1.5m above ground plane above 1GHz. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. For the radiated emission test above 1GHz: Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. 5. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 6. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 7. Repeat above procedures until the measurements for all frequencies are complete. 8. Based on the Frequency Generator in the device include 16MHz.The test frequency range from 9KHz to 25GHz per FCC PART 15.33(a). Note: Three axes are chosen for pretest, the X axis is the worst mode for final test. For battery operated equipment, the equipment tests shall be performed using a fully-charged battery.

V1.0 Page 15 of 29 Report No.: CTL1609053410-WF TEST RESULTS All the test modes (TM1, TM2, TM3 and TM4) completed for test. The worst case of Radiated Emission is TM1; the test data of this mode was reported. Below 1GHz Test Results: Remark： (1) Measuring frequencies from 9 KHz to the 1 GHz, Radiated emission test from 9KHz to 30MHz was verified, and no any emission was found except system noise floor. (2) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (3) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz.

V1.0 Page 16 of 29 Report No.: CTL1609053410-WF Remark： (1) Measuring frequencies from 9 KHz to the 1 GHz, Radiated emission test from 9KHz to 30MHz was verified, and no any emission was found except system noise floor. (2) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (3) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz.

V1.0 Page 17 of 29 Report No.: CTL1609053410-WF Above 1 GHz Test Results: Antenna Pre- Frequency Emission Limit Margin Raw Cable Correction Factor amplifier (MHz) Level (dBuV/m) (dB) Value (dB/m) Factor (dB) Factor (dBuV/m) (dBuV) (dB) (dB/m) 2402.00 97.79 PK 114 16.21 99.75 28.78 4.61 35.36 -1.96 2402.00 88.54 AV 94 5.46 90.50 28.78 4.61 35.36 -1.96 2390.00 69.27 PK 74 4.73 71.31 28.72 4.60 35.36 -2.04 2390.00 49.05 AV 54 4.95 51.09 28.72 4.60 35.36 -2.04 2400.00 70.32 PK 74 3.68 72.29 28.78 4.61 35.36 -1.97 2400.00 49.86 AV 54 4.14 51.83 28.78 4.61 35.36 -1.97 4804.00 68.02 PK 74 5.98 63.51 33.49 6.91 35.89 4.51 4804.00 47.33 AV 54 6.67 42.82 33.49 6.91 35.89 4.51 6244.00 62.95 PK 74 11.05 54.50 35.19 7.97 34.71 8.45 6244.00 44.71 AV 54 9.29 36.26 35.19 7.97 34.71 8.45 7206.00 64.86 PK 74 9.14 53.75 36.95 9.18 35.03 11.11 7206.00 45.07 AV 54 8.93 33.96 36.95 9.18 35.03 11.11 Antenna Pre- Frequency Emission Limit Margin Raw Cable Correction Factor amplifier (MHz) Level (dBuV/m) (dB) Value (dB/m) Factor (dB) Factor (dBuV/m) (dBuV) (dB) (dB/m) 2441.00 97.11 PK 114 16.89 98.97 28.85 4.66 35.37 -1.86 2441.00 89.94 AV 94 4.06 91.80 28.85 4.66 35.37 -1.86 3200.00 62.86 PK 74 11.14 61.50 31.24 5.47 35.35 1.36 3200.00 45.04 AV 54 8.96 43.68 31.24 5.47 35.35 1.36 3416.00 63.72 PK 74 10.28 61.60 31.59 5.73 35.20 2.12 3416.00 42.68 AV 54 11.32 40.56 31.59 5.73 35.20 2.12 4882.00 69.39 PK 74 4.61 63.03 33.60 6.95 34.19 6.36 4882.00 47.05 AV 54 6.95 40.69 33.60 6.95 34.19 6.36 6239.00 64.43 PK 74 9.57 55.99 35.19 7.96 34.71 8.44 6239.00 46.06 AV 54 7.94 37.62 35.19 7.96 34.71 8.44 7323.00 65.52 PK 74 8.48 53.82 37.46 9.23 35.00 11.70 7323.00 47.15 AV 54 6.85 35.45 37.46 9.23 35.00 11.70

V1.0 Page 18 of 29 Report No.: CTL1609053410-WF Antenna Pre- Frequency Emission Limit Margin Raw Cable Correction Factor amplifier (MHz) Level (dBuV/m) (dB) Value (dB/m) Factor (dB) Factor (dBuV/m) (dBuV) (dB) (dB/m) 2480.00 97.47 PK 114 16.53 99.22 28.92 4.70 35.38 -1.75 2480.00 89.51 AV 94 4.49 91.26 28.92 4.70 35.38 -1.75 2483.50 63.85 PK 74 10.15 65.59 28.93 4.70 35.38 -1.74 2483.50 46.29 AV 54 7.71 48.03 28.93 4.70 35.38 -1.74 3720.00 64.03 PK 74 9.97 60.83 32.77 6.08 35.65 3.20 3720.00 46.08 AV 54 7.92 42.88 32.77 6.08 35.65 3.20 4960.00 66.29 PK 74 7.71 59.59 33.84 7.00 34.14 6.70 4960.00 48.74 AV 54 5.26 42.04 33.84 7.00 34.14 6.70 6200.00 63.80 PK 74 10.2 55.40 35.19 7.90 34.69 8.40 6200.00 45.91 AV 54 8.09 37.51 35.19 7.90 34.69 8.40 7440.00 66.07 PK 74 7.93 54.12 37.64 9.28 34.97 11.95 7440.00 45.08 AV 54 8.92 33.13 37.64 9.28 34.97 11.95 Note: above 10GHz up to 25GHz was verified, and no any emission was found except system noise floor. Remark: RBW=1MHz VBW =3MHz peak detector for PK value, RMS detector for AV value GFSK,8DPSK,π/4DQPSK mode all have been tested , only the worst case mode GFSK(1Mbps) is reported. H and V polarity all have been tested ，only worse case Vertical is reported.

V1.0 Page 19 of 29 Report No.: CTL1609053410-WF 4.3. Occupied Bandwidth Measurement Measurement Procedure 1. Set EUT as normal operation. 2. RBW ≥ 1% of the 20 dB bandwidth, VBW≥RBW. 3. The useful conducted emission from the EUT was detected by the spectrum analyser with peak detector. Measurement Results GFSK: 2402MHz 20dB Bandwidth: 1104 KHz 2441MHz 20dB Bandwidth: 1102 KHz

V1.0 Page 20 of 29 Report No.: CTL1609053410-WF 2480MHz 20dB Bandwidth: 1103 KHz π/4DQPSK mode: 2402MHz 20dB Bandwidth: 1333 KHz 2441MHz 20dB Bandwidth: 1326 KHz

V1.0 Page 21 of 29 Report No.: CTL1609053410-WF 2480MHz 20dB Bandwidth: 1340 KHz 8DPSK mode: 2402MHz 20dB Bandwidth: 1325 KHz 2441MHz 20dB Bandwidth: 1335 KHz

V1.0 Page 22 of 29 Report No.: CTL1609053410-WF 2480MHz 20dB Bandwidth: 1338 KHz

V1.0 Page 23 of 29 Report No.: CTL1609053410-WF 5. Antenna Requirement Standard Applicable For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (c), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. Refer to statement below for compliance. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. Further, this requirement does not apply to intentional radiators that must be professionally installed. Antenna Connected Construction The antenna used in this product is PCB Antenna, The directional gains of antenna used for transmitting is 0 dBi.

V1.0 Page 24 of 29 Report No.: CTL1609053410-WF 6. Test Setup Photos of the EUT

V1.0 Page 25 of 29 Report No.: CTL1609053410-WF

V1.0 Page 26 of 29 Report No.: CTL1609053410-WF 7. External and Internal Photos of the EUT External Photos of EUT

V1.0 Page 27 of 29 Report No.: CTL1609053410-WF

V1.0 Page 28 of 29 Report No.: CTL1609053410-WF Internal Photos of EUT

V1.0 Page 29 of 29 Report No.: CTL1609053410-WF ......................End of Report........................


Document Created: 2016-09-27 15:18:50
Document Modified: 2016-09-27 15:18:50
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC