Test Report

FCC ID: 2AJPM-RCONE

Test Report

Download: PDF
FCCID_3956235

FCC PART 15.247 TEST REPORT For Giant Electric Vehicle (KunShan) Co., LTD NO.1 Yue He South Rd. Kun Shan City .Jiangsu China 215300 FCC ID: 2AJPM-RCONE This Report Concerns: Equipment Type: Original Report RideControl Test Engineer: Gin Zuo Report Number: RSHA180621003-00B Report Date: 2018-07-10 Reviewed By: Oscar Ye RF Leader Test Laboratory: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road,Kunshan,Jiangsu province,China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0.

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B TABLE OF CONTENTS GENERAL INFORMATION .......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3 OBJECTIVE ...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................3 TEST METHODOLOGY ..................................................................................................................................................3 MEASUREMENT UNCERTAINTY ....................................................................................................................................4 TEST FACILITY .............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................5 EQUIPMENT MODIFICATIONS .......................................................................................................................................5 EUT EXERCISE SOFTWARE ..........................................................................................................................................5 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................................6 EXTERNAL I/O CABLE..................................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................7 SUMMARY OF TEST RESULTS ...............................................................................................................................8 TEST EQUIPMENT LIST ...........................................................................................................................................9 MEASUREMENT RESULT ............................................................................................................................................10 FCC §15.203 - ANTENNA REQUIREMENT...........................................................................................................11 APPLICABLE STANDARD ............................................................................................................................................11 ANTENNA CONNECTOR CONSTRUCTION ....................................................................................................................11 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS.............................................................................12 APPLICABLE STANDARD ............................................................................................................................................12 EUT SETUP ................................................................................................................................................................12 EMI TEST RECEIVER SETUP .......................................................................................................................................13 TEST PROCEDURE ......................................................................................................................................................13 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................13 TEST RESULTS SUMMARY ..........................................................................................................................................13 TEST DATA ................................................................................................................................................................14 FCC §15.247(a) (2) - 6 dB EMISSION BANDWIDTH ............................................................................................22 APPLICABLE STANDARD ............................................................................................................................................22 TEST PROCEDURE ......................................................................................................................................................22 TEST DATA ................................................................................................................................................................22 FCC §15.247(b) (3) - MAXIMUM CONDUCTED OUTPUT POWER ..................................................................25 APPLICABLE STANDARD ............................................................................................................................................25 TEST PROCEDURE ......................................................................................................................................................25 TEST DATA ................................................................................................................................................................25 FCC §15.247(d) - BAND EDGE .................................................................................................................................28 APPLICABLE STANDARD ............................................................................................................................................28 TEST PROCEDURE ......................................................................................................................................................28 TEST DATA ................................................................................................................................................................28 FCC §15.247(e) - POWER SPECTRAL DENSITY .................................................................................................30 APPLICABLE STANDARD ............................................................................................................................................30 TEST PROCEDURE ......................................................................................................................................................30 TEST DATA ................................................................................................................................................................30 FCC Part 15.247 Page 2 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B GENERAL INFORMATION Product Description for Equipment under Test (EUT) Applicant: Giant Electric Vehicle (KunShan) Co., LTD Tested Model: RideControl ONE Product Type: RideControl Dimension: 45 mm(L)×35 mm(W)×10 mm(H) Power Supply: DC 5.0V *All measurement and test data in this report was gathered from production sample serial number: 20180621003. (Assigned by the BACL. The EUT supplied by the applicant was received on 2018-06-21) Objective This report is prepared on behalf of Giant Electric Vehicle (KunShan) Co., LTD in accordance with Part 2- Subpart J, Part 15-Subparts A and C of the Federal Communication Commissions rules. The tests were performed in order to determine compliance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.209 and 15.247 rules. Related Submittal(s)/Grant(s) No Related Submittal(s)/Grant(s). Test Methodology All measurements contained in this report were conducted with ANSI C63.10-2013, American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices and FCC KDB558074 D01 DTS Meas Guidance v04. All emissions measurement was performed at Bay Area Compliance Laboratories Corp. (Kunshan). The radiated testing was performed at an antenna-to-EUT distance of 3 meters. FCC Part 15.247 Page 3 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Measurement Uncertainty Item Uncertainty AC Power Lines Conducted Emissions 3.19 dB RF conducted test with spectrum 0.9dB RF Output Power with Power meter 0.5dB 30MHz~1GHz 6.11dB 1GHz~6GHz 4.45dB Radiated emission 6GHz~18GHz 5.23dB 18GHz~40GHz 5.65dB Occupied Bandwidth 0.5kHz Temperature 1.0℃ Humidity 6% Test Facility The test site used by Bay Area Compliance Laboratories Corp. (Kunshan) to collect test data is located on the No.248 Chenghu Road, Kunshan, Jiangsu province, China. Bay Area Compliance Laboratories Corp. (Kunshan) Lab is accredited to ISO/IEC 17025 by A2LA (Lab code: 4323.01) and the FCC designation No. CN1185 under the FCC KDB 974614 D01. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-2014. FCC Part 15.247 Page 4 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B SYSTEM TEST CONFIGURATION Description of Test Configuration Channel List for BLE mode: Frequency Frequency Channel Channel (MHz) (MHz) 0 2402 20 2442 1 2404 … … … … … … … … … … 18 2438 38 2478 19 2440 39 2480 EUT was tested with channel 0, 19 and 39. Equipment Modifications No modification was made to the EUT tested. EUT Exercise Software RF test tool: nRFgo Studio Power Level: 0 Duty Cycle: Middle Channel Date:25.JUN.2018 16:02:49 FCC Part 15.247 Page 5 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Mode Duty Cycle (%) T(ms) 1/T(kHz) 10log(1/x) BLE 47.92 0.300 3.333 3.19 Note: “x” means the Duty Cycle. Support Equipment List and Details Manufacturer Description Model Serial Number DELL Notebook GX620 D65874152 ZHAOXIN DC Power Supply RXN-605D / External I/O Cable Length Cable Description From Port To (m) COM-USB Cable 1.2 EUT Notebook Power Cable 0.8 EUT DC Power Supply FCC Part 15.247 Page 6 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Block Diagram of Test Setup For Radiated Emissions(Below 1GHz): Turntable 2m Diameter Notebook EUT DC Power Supply 1.0 Meter Non-Conductive Table 80cm above Ground Plane 1.5 Meter For Radiated Emissions(Above 1GHz): Turntable 2m Diameter DC EUT Notebook Power Supply 1.0 Meter Non-Conductive Table 150cm above Ground Plane 1.5 Meter FCC Part 15.247 Page 7 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B SUMMARY OF TEST RESULTS FCC Rules Description of Test Result §15.247 (I), §1.1310 & §2.1093 RF Exposure Compliant §15.203 Antenna Requirement Compliant Not Applicant §15.207 (a) AC Line Conducted Emissions (Note 1) §15.247(d) Spurious Emissions at Antenna Port Compliant §15.205, §15.209, Spurious Emissions Compliant §15.247(d) §15.247 (a)(2) 6 dB Emission Bandwidth Compliant §15.247(b)(3) Maximum Conducted Output Power Compliant §15.247(d) Band Edge Compliant §15.247(e) Power Spectral Density Compliant Note 1: The EUT is a battery operated device. FCC Part 15.247 Page 8 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B TEST EQUIPMENT LIST Serial Calibration Calibration Manufacturer Description Model Number Date Due Date Radiated Emission Test（Chamber 1#） Rohde & Schwarz EMI Test Receiver ESCI 100195 2017-11-25 2018-11-24 Sunol Sciences Broadband Antenna JB3 A040914-2 2016-01-09 2019-01-08 Sonoma Instrunent Pre-amplifier 310N 171205 2017-08-15 2018-08-14 ZHAOXIN DC Power Supply RXN-605D / 2017-10-10 2018-10-09 Rohde & Schwarz Auto test Software EMC32 100361 / / MICRO-COAX Coaxial Cable Cable-8 008 2017-08-15 2018-08-14 MICRO-COAX Coaxial Cable Cable-9 009 2017-08-15 2018-08-14 MICRO-COAX Coaxial Cable Cable-10 010 2017-08-15 2018-08-14 Radiated Emission Test（Chamber 2#） Rohde & Schwarz EMI Test Receiver ESU40 100207 2017-08-27 2018-08-26 ETS-LINDGREN Horn Antenna 3115 6229 2016-01-11 2019-01-10 ETS-LINDGREN Horn Antenna 3116 00084159 2016-10-18 2019-10-17 Mini-Circuits Amplifier ZVA-183W-S+ 220701818 2018-05-20 2019-05-19 EM Electronics Amplifier EM18G40G 060726 2018-03-22 2019-03-21 Corporation MICRO-TRONICS Notch filter BRM50702 / 2017-08-05 2018-08-04 Narda Attenuator/10dB 10dB / 2017-08-15 2018-08-14 ZHAOXIN DC Power Supply RXN-605D / 2017-10-10 2018-10-09 Rohde & Schwarz Auto test Software EMC32 100361 / / MICRO-COAX Coaxial Cable Cable-6 006 2017-08-15 2018-08-14 MICRO-COAX Coaxial Cable Cable-11 011 2017-08-15 2018-08-14 MICRO-COAX Coaxial Cable Cable-12 012 2017-08-15 2018-08-14 MICRO-COAX Coaxial Cable Cable-13 013 2017-08-15 2018-08-14 RF Conducted Test Rohde & Schwarz FSV40 Signal Analyzer FSV40 101116 2017-07-22 2018-07-21 Narda Attenuator/2dB 2dB / 2017-08-15 2018-08-14 ZHAOXIN DC Power Supply RXN-605D / 2017-10-10 2018-10-09 Giant RF Cable / / Each Time / * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Kunshan) attests that all calibrations have been performed in accordance to requirements that traceable to National Primary Standards and International System of Units (SI). FCC Part 15.247 Page 9 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B FCC§15.247 (i), §1.1310 &§2.1093 –RF EXPOSURE Applicable Standard According to§2.1093and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to KDB 447498 D01 General RF Exposure Guidance The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where 1. f(GHz) is the RF channel transmit frequency in GHz. 2. Power and distance are rounded to the nearest mW and mm before calculation. 3. The result is rounded to one decimal place for comparison. 4. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test Exclusion. Measurement Result For worst case: Max Tune-up Calculated Frequency Range Conducted Power Calculated Threshold SAR Test Mode Distance (MHz) Value (1-g SAR) Exclusion (mm) (dBm) (mW) BLE 2402-2480 -8.00 0.16 5.0 0.1 3.0 Yes Result: No SAR test is required. FCC Part 15.247 Page 10 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B FCC §15.203 - ANTENNA REQUIREMENT Applicable Standard According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the user of a standard antenna jack or electrical connector is prohibited. The structure and application of the EUT were analyzed to determine compliance with section §15.203 of the rules. §15.203 state that the subject device must meet the following criteria: a. Antenna must be permanently attached to the unit. b. Antenna must use a unique type of connector to attach to the EUT. Unit must be professionally installed, and installer shall be responsible for verifying that the correct antenna is employed with the unit. And according to FCC 47 CFR section 15.247 (b), if the transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. Antenna Connector Construction The EUT has a ceramic antenna for BLE, which the antenna gain is 5.05 dBi, fulfill the requirement of this section. Please refer to the EUT photos. Result: Compliance. FCC Part 15.247 Page 11 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS Applicable Standard FCC §15.247 (d); §15.209; §15.205; EUT Setup Below 1 GHz: Above 1GHz: The radiated emission tests were performed in the 3 meters test site, using the setup accordance with the ANSI C63.10-2013. The specification used was the FCC 15.209, and FCC 15.247 limits. FCC Part 15.247 Page 12 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B EMI Test Receiver Setup The system was investigated from 30 MHz to 25 GHz. During the radiated emission test, the EMI test receiver Setup was set with the following configurations: Frequency Range RBW Video B/W IF B/W Detector 30 MHz - 1000 MHz 120 kHz 300 kHz 120 kHz QP 1MHz 3 MHz / PK Above 1GHz 1MHz 3 MHz / Ave Test Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz - 1 GHz, peak and Average detection modes for frequencies above 1 GHz. Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude (dBμV /m) = Meter Reading (dBμV) + Antenna Factor (dB/m) + Cable Loss (dB) - Amplifier Gain (dB) The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin (dB) = Limit (dBμV/m) - Corrected Amplitude (dBμV /m) Test Results Summary According to the recorded data in following table, the EUT complied with the FCC Title 47, Part 15, Subpart C, section 15.205, 15.209 and 15.247. FCC Part 15.247 Page 13 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Test Data Environmental Conditions Temperature: 24.2℃ Relative Humidity: 51 % ATM Pressure: 101.2 kPa The testing was performed by Gin Zuo on 2018-06-25 to 2018-07-03. EUT operation mode: Transmitting Spurious Emission Test: 30MHz-1GHz (Pre-scan with low, middle and high channels of operation in the X,Y and Z axes of orientation, the worst case high channel of operation in X-axis of orientation was recorded) 80 60 dBμV/m dBμV/ 40 in in Level Level 20 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz Corrected Rx Antenna Corrected Frequency Amplitude Turntable Limit Margin Degree Factor (MHz) QuasiPeak Height Polar (dBμV/m) (dB) (dB/m) (dBμV/m) (cm) (H/V) 32.778750 19.76 199.0 V 209.0 -6.3 40.00 20.24 99.557250 27.15 101.0 V 180.0 -15.5 43.50 16.35 119.989700 29.03 101.0 V 273.0 -11.6 43.50 14.47 232.335950 34.48 101.0 V 23.0 -12.6 46.00 11.52 411.895550 32.97 101.0 V 196.0 -8.3 46.00 13.03 600.009750 35.44 101.0 V 201.0 -5.4 46.00 10.56 FCC Part 15.247 Page 14 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B 1GHz-18GHz (Pre-scan in the X,Y and Z axes of orientation, the worst case X-axis of orientation was recorded.) Note: 1. This test was performed with the 2.4 - 2.5GHz notch filter. 2. Corrected Factor (dB/m) = Antenna factor (RX) (dB/m) + Cable Loss (dB) - Amplifier Factor (dB) Corrected Amplitude (dBμV/m) = Corrected Factor (dB/m) + Reading (dBμV) Margin (dB) = Limit (dBμV/m) - Corrected Amplitude (dBμV /m) Low Channel: 2402MHz Full Spectrum 100 Fundamental Test with notch filter 80 Level inindBμV/m dBμV/ 60 40 Level 20 0 1G 2G 3G 4G 5G 6 8 10G 18G Frequency in Hz Corrected Amplitude Rx Antenna Corrected Frequency Turntable Limit Margin MaxPeak Average Height Polar Degree Factor (MHz) (dBμV/m) (dB) (dBμV /m) (dBμV /m) (cm) (H/V) (dB/m) 1584.800000 --- 29.45 100.0 V 13.0 -0.6 54.00 24.55 1584.800000 40.25 --- 100.0 V 13.0 -0.6 74.00 33.75 3274.600000 --- 35.87 200.0 H 313.0 6.7 54.00 18.13 3274.600000 46.58 --- 200.0 H 313.0 6.7 74.00 27.42 4804.000000 --- 39.61 150.0 V 67.0 10.7 54.00 14.39 4804.000000 49.80 --- 150.0 V 67.0 10.7 74.00 24.20 7206.000000 --- 43.37 200.0 V 293.0 15.2 54.00 10.63 7206.000000 51.70 --- 200.0 V 293.0 15.2 74.00 22.30 9989.600000 --- 46.79 150.0 V 263.0 18.3 54.00 7.21 9989.600000 55.24 --- 150.0 V 263.0 18.3 74.00 18.76 17840.200000 --- 46.54 150.0 H 114.0 19.0 54.00 7.46 17840.200000 58.02 --- 150.0 H 114.0 19.0 74.00 15.98 FCC Part 15.247 Page 15 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Middle Channel: 2440MHz Full Spectrum 100 Fundamental Test with notch filter 80 dBμV/ dBμV/m 60 in in 40 Level Level 20 0 1G 2G 3G 4G 5G 6 8 10G 18G Frequency in Hz Corrected Amplitude Rx Antenna Corrected Frequency Turntable Limit Margin MaxPeak Average Height Polar Factor (MHz) Degree (dBμV/m) (dB) (dBμV /m) (dBμV /m) (cm) (H/V) (dB/m) 1482.800000 --- 27.42 150.0 V 305.0 -1.4 54.00 26.58 1482.800000 38.27 --- 150.0 V 305.0 -1.4 74.00 35.73 3070.600000 --- 37.23 150.0 V 266.0 6.2 54.00 16.77 3070.600000 46.61 --- 150.0 V 266.0 6.2 74.00 27.39 4880.000000 --- 38.97 200.0 V 38.0 11.1 54.00 15.03 4880.000000 50.47 --- 200.0 V 38.0 11.1 74.00 23.53 7320.000000 --- 42.72 150.0 V 169.0 15.4 54.00 11.28 7320.000000 51.34 --- 150.0 V 169.0 15.4 74.00 22.66 9877.400000 --- 45.76 200.0 V 290.0 18.2 54.00 8.24 9877.400000 56.46 --- 200.0 V 290.0 18.2 74.00 17.54 17853.800000 --- 45.58 150.0 H 156.0 19.0 54.00 8.42 17853.800000 56.94 --- 150.0 H 156.0 19.0 74.00 17.06 FCC Part 15.247 Page 16 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B High Channel: 2480MHz Full Spectrum 100 80 LevelinindBμV/m dBμV/ 60 40 Level 20 0 1G 2G 3G 4G 5G 6 8 10G 18G Frequency in Hz Corrected Amplitude Rx Antenna Corrected Frequency Turntable Limit Margin MaxPeak Average Height Polar Factor (MHz) Degree (dBμV/m) (dB) (dBμV /m) (dBμV /m) (cm) (H/V) (dB/m) 1363.800000 --- 28.85 200.0 H 0.0 -2.0 54.00 25.15 1363.800000 39.39 --- 200.0 H 0.0 -2.0 74.00 34.61 3070.600000 --- 37.16 150.0 V 256.0 6.2 54.00 16.84 3070.600000 46.52 --- 150.0 V 256.0 6.2 74.00 27.48 4960.000000 --- 40.47 150.0 H 99.0 11.5 54.00 13.53 4960.000000 49.11 --- 150.0 H 99.0 11.5 74.00 24.89 7440.000000 --- 43.39 200.0 H 108.0 15.6 54.00 10.61 7440.000000 51.26 --- 200.0 H 108.0 15.6 74.00 22.74 9918.200000 --- 46.56 200.0 V 42.0 18.2 54.00 7.44 9918.200000 55.55 --- 200.0 V 42.0 18.2 74.00 18.45 17867.400000 --- 46.23 150.0 V 234.0 19.0 54.00 7.77 17867.400000 56.45 --- 150.0 V 234.0 19.0 74.00 17.55 FCC Part 15.247 Page 17 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B 18GHz - 25GHz (Pre-scan with low, middle and high channels of operation in the X,Y and Z axes of orientation, the worst case high channel of operation in X-axis of orientation was recorded) Horizontal RBW 1 MHz Marker 1 [T1 ] * VBW 3 MHz 57.14 dBµV Ref 97 dBµV * Att 10 dB SWT 45 ms 24.943910256 GHz Marker 2 [T2 ] 46.47 dBµV 90 24.842948718 GHz A 1 PK 80 MAXH D1 74 dBµV 2 AV * 70 TDF MAXH 60 1 PS D2 54 dBµV 50 2 40 6DB AC 30 20 10 0 Start 18 GHz 700 MHz/ Stop 25 GHz Date: 3.JUL.2018 10:24:43 Vertical RBW 1 MHz Marker 1 [T1 ] * VBW 3 MHz 56.59 dBµV Ref 97 dBµV * Att 10 dB SWT 45 ms 24.977564103 GHz Marker 2 [T2 ] 46.01 dBµV 90 24.854166667 GHz A 1 PK 80 MAXH D1 74 dBµV 2 AV * 70 TDF MAXH 60 1 PS D2 54 dBµV 50 2 40 6DB AC 30 20 10 0 Start 18 GHz 700 MHz/ Stop 25 GHz Date: 3.JUL.2018 10:37:21 FCC Part 15.247 Page 18 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Fundamental Test & Restricted Bands Emissions Test: (Pre-scan in the X, Y and Z axes of orientation, the worst case X-axis of orientation was recorded.) Note: 1. Corrected Factor (dB/m) = Antenna factor (RX) (dB/m) + Cable Loss (dB) - Amplifier Factor (dB) Corrected Amplitude (dBμV/m) = Corrected Factor (dB/m) + Reading (dBμV) Margin (dB) = Limit (dBμV/m) - Corrected Amplitude (dBμV /m) Corrected Amplitude Rx Antenna Corrected Frequency Turntable Limit Margin MaxPeak Average Height Polar Factor (MHz) Degree (dBμV/m) (dB) (dBμV /m) (dBμV /m) (cm) (H/V) (dB/m) Low Channel: 2402MHz 2402.00 87.25 --- 150.0 V 274.0 2.8 / / 2402.00 --- 78.37 150.0 V 274.0 2.8 / / 2402.00 84.42 --- 200.0 H 324.0 2.8 / / 2402.00 --- 75.19 200.0 H 324.0 2.8 / / 2390.00 47.63 --- 150.0 V 96.0 2.8 74.00 26.37 2390.00 --- 31.98 150.0 V 96.0 2.8 54.00 22.02 Middle Channel: 2440MHz 2440.00 91.85 --- 250.0 V 91.0 2.9 / / 2440.00 --- 82.05 250.0 V 91.0 2.9 / / 2440.00 88.76 --- 150.0 H 197.0 2.9 / / 2440.00 --- 79.71 150.0 H 197.0 2.9 / / High Channel: 2480MHz 2480.00 90.62 --- 150.0 V 210.0 3.0 / / 2480.00 --- 81.72 150.0 V 210.0 3.0 / / 2480.00 87.31 --- 200.0 H 118.0 3.0 / / 2480.00 --- 78.26 200.0 H 118.0 3.0 / / 2483.50 54.79 --- 150.0 V 105.0 3.0 74.00 19.21 2483.50 --- 35.40 150.0 V 105.0 3.0 54.00 18.60 FCC Part 15.247 Page 19 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Conducted Spurious Emissions at Antenna Port: Low Channel Date:25.JUN.2018 16:22:29 Middle Channel Date:25.JUN.2018 16:30:23 FCC Part 15.247 Page 20 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B High Channel Date:25.JUN.2018 16:18:11 FCC Part 15.247 Page 21 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B FCC §15.247(a) (2) - 6 dB EMISSION BANDWIDTH Applicable Standard Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. Test Procedure According to KDB558074 D01 DTS Meas Guidance v04 sub-clause 8.1 1. Set RBW = 100 kHz. 2. Set the video bandwidth (VBW) ≥ 3xRBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. Spectrum Analyzer Attenuator EUT Test Data Environmental Conditions Temperature: 24.2℃ Relative Humidity: 51 % ATM Pressure: 101.2 kPa The testing was performed by Gin Zuo on 2018-06-25. Test Result: Pass. EUT operation mode: Transmitting 6 dB Emission Frequency Limit Channel Bandwidth (MHz) (MHz) (MHz) Low 2402 0.703 ≥ 0.5 Middle 2440 0.712 ≥ 0.5 High 2480 0.716 ≥ 0.5 FCC Part 15.247 Page 22 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Low Channel Date:25.JUN.2018 15:23:41 Middle Channel Date:25.JUN.2018 15:21:21 FCC Part 15.247 Page 23 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B High Channel Date:25.JUN.2018 15:22:31 FCC Part 15.247 Page 24 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B FCC §15.247(b) (3) - MAXIMUM CONDUCTED OUTPUT POWER Applicable Standard According to FCC §15.247(b) (3), for systems using digital modulation in the 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz bands: 1 Watt. As an alternative to a peak power measurement, compliance with the one Watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted Output Power is defined as the total transmit power delivered to all antennas and antenna elements averaged across all symbols in the signaling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or is transmitting at a reduced power level. If multiple modes of operation are possible (e.g., alternative modulation methods), the maximum conducted output power is the highest total transmit power occurring in any mode. Test Procedure According to KDB558074 D01 DTS Meas Guidance v04 1. Set the RBW ≥ DTS bandwidth. 2. Set VBW ≥ 3 x RBW. 3. Set span ≥ 3 x RBW 4. Sweep time = auto couple. 5. Detector = peak. 6. Trace mode = max hold. 7. Allow trace to fully stabilize. 8. Use peak marker function to determine the peak amplitude level. Signal Analyzer Attenuator EUT Test Data Environmental Conditions Temperature: 24.2℃ Relative Humidity: 51 % ATM Pressure: 101.2 kPa The testing was performed by Gin Zuo on 2018-06-25. FCC Part 15.247 Page 25 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B EUT operation mode: Transmitting Max Conducted Frequency Limit Channel Peak Output Power Result (MHz) (dBm) (dBm) Low 2402 -12.33 30 Pass Middle 2440 -10.43 30 Pass High 2480 -8.77 30 Pass Low Channel Date:25.JUN.2018 14:55:18 FCC Part 15.247 Page 26 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Middle Channel Date:25.JUN.2018 14:56:52 High Channel Date:25.JUN.2018 14:57:26 FCC Part 15.247 Page 27 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B FCC §15.247(d) - BAND EDGE Applicable Standard In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)). Test Procedure According to KDB558074 D01 DTS Meas Guidance v04 sub-clause 13.2 and ANSI C63.10-2013 clause 6.10. 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range, and make sure the instrument is operated in its linear range. 3. Set RBW to 100 kHz and VBW of spectrum analyzer to 300 kHz with a convenient frequency span including 100 kHz bandwidth from band edge. 4. Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. 5. Repeat above procedures until all measured frequencies were complete. Test Data Environmental Conditions Temperature: 24.2℃ Relative Humidity: 51 % ATM Pressure: 101.2 kPa The testing was performed by Gin Zuo on 2018-06-25. EUT operation mode: Transmitting Test Result: Compliance FCC Part 15.247 Page 28 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Left Side Date:25.JUN.2018 15:25:28 Right Side Date:25.JUN.2018 15:26:34 FCC Part 15.247 Page 29 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B FCC §15.247(e) - POWER SPECTRAL DENSITY Applicable Standard For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall be used to determine the power spectral density. Test Procedure According to KDB558074 D01 DTS Meas Guidance v04 sub-clause 10.2 1. Use this procedure when the maximum peak conducted output power in the fundamental emission is used to demonstrate compliance. 2. Set the RBW to: 3kHz≤ RBW≤100 kHz. 3. Set the VBW ≥ 3×RBW. 4. Set the span to 1.5 times the DTS bandwidth. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum amplitude level within the RBW. 10. If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. Test Data Environmental Conditions Temperature: 24.2℃ Relative Humidity: 51 % ATM Pressure: 101.2 kPa The testing was performed by Gin Zuo on 2018-06-25. EUT operation mode: Transmitting Test Result: Pass Frequency PSD Limit Channel (MHz) (dBm/3kHz) (dBm/3kHz) Low 2402 -27.84 ≤8 Middle 2440 -26.11 ≤8 High 2480 -24.34 ≤8 FCC Part 15.247 Page 30 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B Low Channel Date:25.JUN.2018 16:12:28 Middle Channel Date:25.JUN.2018 16:11:35 FCC Part 15.247 Page 31 of 32

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA180621003-00B High Channel Date:25.JUN.2018 16:13:06 ***** END OF REPORT ***** FCC Part 15.247 Page 32 of 32


Document Created: 2018-08-08 09:53:30
Document Modified: 2018-08-08 09:53:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC