I18Z62335-SEM03_SAR_Rev0 up1_153-159

FCC ID: 2AJOTTA-1150

Test Report

Download: PDF
FCCID_4154659

(g, Impedance Measurement Plot for Head TSL File View Channel Sweep Calibration Trace Scale Marker System Window Help 2600000 GHz 47.371 Q 8.2358 pF —7.4326 Q , 2600000 GHz 80.734 mU ~105.12 ° Ch1Avg= 20 Ch1: Start 2.40000 GHz —— Stop 2.90000 GHz a —21.9859 dB 00 Ch = Ch1: Start 2.40000 GHz —— Stop 2.20000 GHz Status CH 1: 511 xt C" 1—Port Avg=20 Delay LCL Certificate No: D2600V2—1012_Jul18 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 26.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN:1012 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.2 S/m; & = 51.5; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.81, 7.81, 7.81) @ 2600 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 e Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 «_ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 107.5 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 27.7 W/kg SAR(I g) = 13.7 W/kg; SAR(10 g) = 6.17 W/kg Maximum value of SAR (measured) = 22.6 W/kg dB 0 —5.20 —10.40 —15.60 —20.80 —26.00 0 dB = 22.6 W/kg = 13.54 dBW/kg Certificate No: D2600V2—1012_Jul18 Page 7 of 8

© Impedance Measurement Plot for Body TSL File View Channel Sweep Calibration Trace Scale Marker System Window Help 2.600000 GHz 44.132 O 12.374 pF —4.9469 Q y 2600000 GHz 81.418 mU —136.86 ° Ch1Avg= 20 Ch1: Start 2.40000 GHz —— Stop 2.20000 GHz to 00 —2].786 dB 0.00 00 Ch1 Ch1: Start 2. Stop 2.90000 GHz Status CH 1: E11 ] C" 1—Port Avg=20 Delay LCL Certificate No: D2600V2—1012_Jul18 Page 8 of 8

No.I18Z62335-SEM03 Page 156 of 159 ANNEX I Sensor Triggering Data Summary 1, Maximum transmit power reduce process follow below strategy when mobile connect network. Headset P-sensor SAR sensor TX Power reduce Insert Near Near Yes Insert Near Far No Insert Far Near Yes Insert Far Far No Pull out Near Near No Pull out Near Far No Pull out Far Near Yes Pull out Far Far No 2, Distance definition P-sensor Detect Near Far Distance Detected <3cm >=5cm SAR Sensor Detect Near Far rear <=16mm >16mm front <=12mm >12mm bottom <=16mm >16mm top Not Detect Not Detect right Not Detect Not Detect left Not Detect Not Detect 3, Reduction and Bands Conduct power Band Requirement reduction DCS 2、3、4 Slots 3.5dB PCS 2、3、4 Slots 3dB WB1 2dB LTE B1 2.5dB LTE B3 2dB LTE B7 2dB ©Copyright. All rights reserved by CTTL.

No.I18Z62335-SEM03 Page 157 of 159 According to the above description, this device was tested by the manufacturer to determine the SAR sensor triggering distances for the rear and bottom edge of the device. The measured power state within ±5mm of the triggering points (or until touching the phantom) is included for rear and each applicable edge. To ensure all production units are compliant it is necessary to test SAR at a distance 1mm less than the smallest distance from the device and SAR phantom with the device at maximum output power without power reduction. We tested the power and got the different proximity sensor triggering distances for rear and bottom edge. But the manufacturer has declared 16mm is the most conservative triggering distance for main antenna. So base on the most conservative triggering distance of 16mm, additional SAR measurements were required at 15mm from the highest SAR position between rear and bottom edge of main antenna. Rear Moving device toward the phantom: The power state Distance [mm] 21 20 19 18 17 16 15 14 13 12 11 Main antenna Normal Normal Normal Normal Normal Low Low Low Low Low Low Moving device away from the phantom: The power state Distance [mm] 11 12 13 14 15 16 17 18 19 20 21 Main antenna Low Low Low Low Low Low Normal Normal Normal Normal Normal Bottom Edge Moving device toward the phantom: The power state Distance [mm] 21 20 19 18 17 16 15 14 13 12 11 Main antenna Low Low Low Low Low Low Low Low Low Low Low Moving device away from the phantom: The power state Distance [mm] 11 12 13 14 15 16 17 18 19 20 21 Main antenna Low Low Low Low Low Low Low Low Low Low Low ©Copyright. All rights reserved by CTTL.

No.I18Z62335-SEM03 Page 158 of 159 The influence of table tilt angles to proximity sensor triggering is determined by positioning each edge that contains a transmitting antenna, perpendicular to the flat phantom, at the smallest sensor triggering test distance by rotating the device around the edge next to the phantom in ≤ 10° increments until the tablet is ±45°or more from the vertical position at 0°. Re ar Body Phantom 45° 16mm 0° 45° ar Re The rear evaluation for main antenna Body Phantom 16mm 45° 45° Top edge 0° Top edge The bottom edge evaluation for main antenna Based on the above evaluation, we come to the conclusion that the sensor triggering is not released and normal maximum output power is not restored within the ±45°range at the smallest sensor triggering test distance declared by manufacturer. ©Copyright. All rights reserved by CTTL.

No.I18Z62335-SEM03 Page 159 of 159 ANNEX J Accreditation Certificate ©Copyright. All rights reserved by CTTL.


Document Created: 2019-01-31 09:28:22
Document Modified: 2019-01-31 09:28:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC