User Manual

FCC ID: 2AJOTTA-1127

Users Manual

Download: PDF
FCCID_4165615

Headset connector Get Started Nokia x Camera Front camera Flash Earpiece Proximity sensor USB connector Loudspeaker Volume keys Power/Lock key TA-1123/TA-1127 EN-LATAM 1. Insert the SIM and memory Note: Switch the device off and disconnect the charger and any other device before removing any card covers. Avoid touching electronic components while changing any covers. Always store and use the 1. With the phone facing down, put your fingernail device with any covers attached. in the seam between the back cover and the display, bend the back cover open, and remove it. Both SIM cards are available at the same time when 2. Slide the SIM card holder to the right and open it the device is not being used, but while one SIM card up. Put a nano-SIM card in the SIM slot with the is active, for example, making a call, the other may contact area face down. Slide the holder to the left be unavailable. to lock it in place. 3. If you have a dual-SIM phone, slide the SIM card Note: On dual SIM capable devices, both SIM1 holder of the SIM2 slot to the left and open it up. and SIM2 slots support 4G networks. However, if Put your second nano-SIM card in the slot with the your SIM1 and SIM2 are both LTE SIM cards, the pri- contact area face down. Close down the holder and mary SIM supports 4G/3G/2G networks, while the slide it to the right to lock it in place. secondary SIM can only support 3G/2G. For more 4. If you have a microSD memory card, slide the information on your SIM cards, contact your service card in the memory card slot. provider. 5. Press the top edge of the back cover against the top edge of your phone, and then snap the cover 2. Charge the battery and switch into place, locking all the hooks around the edges of the cover. the phone on Plug a compatible charger into a wall outlet, and connect the cable to your phone. Your phone sup- ports the USB micro-B cable. You can also charge your phone from a computer with a USB cable, but it may take a longer time. If the battery is completely discharged, it may take several minutes before the charging indicator is dis- played.

To switch your phone on, press and hold the power key until the phone vibrates. The phone guides you Product and safety info compliance with FCC RF exposure requirements, use accessories that maintain a 1,5 cm separation distance between the user’s body and Important: For important info on the safe use of your device and the handset. The use of belt clips, holsters and similar accessories through the setup. battery, read the Product and safety info booklet before you take should not contain metallic components in its assembly. The use of your device into use. accessories that do not satisfy these requirements may not comply You can only use your device on the GSM 850, 900, 1800, 1900; with FCC RF exposure requirements, and should be avoided. The FCC WCDMA 1, 2, 4, 5, 8; LTE 1, 2, 3, 4, 5, 7, 8, 12, 17, 28 networks. has granted an Equipment Authorization for this handset model with You need a subscription with a service provider. all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this handset model is on file Important: 4G/LTE might not be supported by your network with the FCC and can be found under the FCC ID Search section of service provider or by the service provider you are using when www.fcc.gov/oet/ea/ after searching on FCC ID 2AJOTTA-1123 or traveling. In these cases, you may not be able to make or receive 2AJOTTA-1127. calls, send or receive messages or use mobile data connections. To make sure your device works seamlessly when full 4G/LTE service is Additional information on Specific Absorption Rates (SAR) can be not available, it is recommended that you change the highest found on the FCC website at www.fcc.gov/general/radio-frequency- connection speed from 4G to 3G. To do this, on the home screen, tap safety-0. For an online user guide and troubleshooting help, Settings > Network & Internet > Mobile network > Advanced, and To send data or messages, a good connection to the network is go to www.nokia.com/mobile-support. switch Preferred network type to 3G. needed. Sending may be delayed until such a connection is available. For more info, contact your network service provider. Follow the separation distance instructions until the sending is finished. Charge your device with the AD-5WE (EU plug)/ AD-5WX(UK plug)/ AD-5WU (US plug)/AD-5WA (Australia plug)/ AD-5WC (China plug) During general use, the SAR values are usually well below the values chargers. HMD Global may make additional battery or charger models stated above. This is because, for purposes of system efficiency and available for this device. Charging time can vary depending on device to minimise interference on the network, the operating power of your capability. Some of the accessories mentioned in this user guide, mobile is automatically decreased when full power is not needed for such as charger, headset, or data cable, may be sold separately. the call. The lower the power output, the lower the SAR value. Electrical Information of the Charger Device models may have different versions and more than one value. Component and design changes may occur over time and some The following electrical information corresponds to the above- changes could affect SAR values. mentioned charger models: For more info, go to www.sar-tick.com. Note that mobile devices Input: 100-240 Vca; 50-60 Hz 0-150 mA may be transmitting even if you are not making a voice call. Output: 5,0 Vcc 0-1000 mA Your mobile device is also designed to meet the United States Charger safety instructions Federal Communications Commission (FCC) guidelines. FCC ratings The charger is suitable to be used only with compatible devices. for your device and more information on SAR can be found at http:/ /transition.fcc.gov/oet/rfsafety/sar.html. The charger should not be used in extremely high or low temperatures. The World Health Organization (WHO) has stated that current scientific information does not indicate the need for any special Ventilation should not be obstructed by covering the charger with precautions when using mobile devices. If you are interested in magazines, blankets, curtains etc. reducing your exposure, they recommend you limit your usage or use Open flames, such as candles, should not be placed above the a hands-free kit to keep the device away from your head and body. charger. For more information and explanations and discussions on RF The charger and the wall outlet shall be easily accessible at all times. exposure, go to the WHO website at www.who.int/peh-emf/en. In case the cable or the plugs are damaged, stop using it. The charger requires very low maintenance. If you want to clean it, Copyrights and other notices use a dry cloth or a brush. Meaning of the symbols: FCC notice: For internal use only This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause The charger should not be disposed as unsorted municipal harmful interference, and (2) this device must accept any waste. It should be recycled. interference received, including interference that may cause undesired operation. For more info, go to www.fcc.gov/engineering- The surface of the device is nickel-free. technology/electromagnetic-compatibility-division/radio- frequency-safety/faq/rf-safety. Any changes or modifications not Parts of the device are magnetic. Metallic materials may be attracted expressly approved by HMD Global could void the user’s authority to to the device. Do not place credit cards or other magnetic stripe operate this equipment. Note: This equipment has been tested and cards near the device for extended periods of time, since the cards found to comply with the limits for a Class B digital device, pursuant may be damaged. to part 15 of the FCC Rules. These limits are designed to provide Note: Pre-installed system software and apps use a significant reasonable protection against harmful interference in a residential part of memory space. installation. This equipment generates, uses and can radiate radio Keep a safe distance when using the flash. Do not use the flash on frequency energy and, if not installed and used in accordance with people or animals at close range. Do not cover the flash while taking the instructions, may cause harmful interference to radio a photo. communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be Certification information (SAR) determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. This mobile device meets guidelines for exposure to radio waves as • Increase the separation between the equipment and receiver. set forth by the Federal Communications Commission (FCC). Refer to • Connect the equipment into an outlet on a circuit different from the following. that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC RF Exposure Information This device has an electronic label for certification information. To Your handset is a radio transmitter and receiver. It is designed and access it, select Settings > System > Certification. manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The guidelines are based on standards that were developed by independent scientific organization through periodic and thorough evaluation of scientific © 2019 HMD Global. HMD Global Oy is the exclusive licensee of the studies. The standards include a substantial safety margin designed Nokia brand for phones & tablets. Nokia is a registered trademark of to assure the safety of all persons, regardless of age and health. The Nokia Corporation. exposure standard for wireless handsets employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. The tests are performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this handset model as reported to the FCC when tested for use at the ear is 0.97 W/kg, and when worn on the body in a holder or carry case, is 1.09 W/kg. Body-worn Operation; This device was tested for typical body-worn operations with the handset kept 1,5 cm from the body. To maintain


Document Created: 2019-01-29 13:10:40
Document Modified: 2019-01-29 13:10:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC