User manual

FCC ID: 2AJOTTA-1120

Users Manual

Download: PDF
FCCID_3913478

Headset connector Microphone Front camera Main camera Get Started Flash Proximity sensor Nokia xx Fingerprint sensor Earpiece SIM and memory card slot USB connector Microphone Loudspeaker Volume keys Power/Lock key TA-1120/TA-1112 EN-LATAM 1. Insert the SIM and memory 2. Charge the battery and switch card the phone on 1.Open the SIM and memory card tray: push the Plug a compatible charger into a wall outlet, and tray opener pin in the tray hole and slide the tray connect the cable to your phone. Your phone out. supports the USB-C cable. You can also charge your 2. If you have a single-SIM phone, put a nano-SIM phone from a computer with a USB cable, but it may card in slot 1 and a memory card in slot 2 on the take a longer time. tray with the contact areas face down. If you have a dual-SIM phone, put a nano-SIM card in slot 1 and If the battery is completely discharged, it may take several minutes before the charging indicator is either a second SIM or a memory card in slot 2 with displayed. the contact areas face down. 3. Slide the tray back in the slot. To switch your phone on, press and hold the power Use only original nano-SIM cards. Use of incompati- key until the phone vibrates. The phone guides you ble SIM cards may damage the card or the device, through the setup. and may corrupt data stored on the card. Use only compatible memory cards approved for use with this device. Incompatible cards may dam- age the card and the device and corrupt data stored on the card. Important: Do not remove the memory card when an app is using it. Doing so may damage the USB-C USB micro-B memory card and the device and corrupt data stored on the card. For an online user guide and troubleshooting help, Both SIM cards are available at the same time when go to www.nokia.com/mobile-support. the device is not being used, but while one SIM card is active, for example, making a call, the other may be unavailable. PKPDA55017A V1.0 xxxxxxxxxx

Product and safety info positions and locations (e.g. at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this Important: For important info on the safe use of your device and model handset as reported to the FCC when tested for use at the ear battery, read the Product and safety info booklet before you take is 1,10 W/kg, and when worn on the body in a holder or carry case, is your device into use. 1,15 W/kg. You can only use your device on the GSM 850, 900, 1800, 1900, Body-worn Operation; This device was tested for typical body-worn WCDMA 1, 2, 4, 5, 8, LTE 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 28, 38, 40, 66 operations with the handset kept 1,5 cm from the body. To maintain networks. compliance with FCC RF exposure requirements, use accessories that You need a subscription with a service provider. maintain a 1,5 cm separation distance between the user’s body and Important: 4G/LTE might not be supported by your network the handset. The use of belt clips, holsters and similar accessories service provider or by the service provider you are using when should not contain metallic components in its assembly. The use of traveling. In these cases, you may not be able to make or receive accessories that do not satisfy these requirements may not comply calls, send or receive messages or use mobile data connections. To with FCC RF exposure requirements, and should be avoided. The FCC make sure your device works seamlessly when full 4G/LTE service is has granted an Equipment Authorization for this model handset with not available, it is recommended that you change the highest all reported SAR levels evaluated as in compliance with the FCC RF connection speed from 4G to 3G. To do this, on the home screen, tap emission guidelines. SAR information on this model handset is on file Settings > Network & Internet > Mobile network > Advanced, and with the FCC and can be found under the Display Grant section of switch Preferred network type to 3G. www.fcc.gov/oet/ea/ after searching on FCC ID 2AJOTTA-1112 or 2AJOTTA-1120. For more info, contact your network service provider. Additional information on Specific Absorption Rates (SAR) can be Your device has an internal, non-removable, rechargeable battery. found on the FCC website at www.fcc.gov/general/radio-frequency- Do not attempt to remove the battery or back cover, as you may safety-0. damage the device. To replace the battery, take the device to the nearest authorised service facility. To send data or messages, a good connection to the network is needed. Sending may be delayed until such a connection is available. Charge your device with the AD-10WC (CN plug)/AD-10WE (EU plug)/ Follow the separation distance instructions until the sending is AD-10WX (UK plug)/AD-10WN (India plug)/AD-10WU (US plug)/ finished. FC0108 (Argentina plug) charger. HMD Global may make additional battery or charger models available for this device. Charging time can During general use, the SAR values are usually well below the values vary depending on device capability. Third-party chargers that stated above. This is because, for purposes of system efficiency and comply with the applicable USB requirements, and that can connect to minimise interference on the network, the operating power of your to your device USB connector, may also be compatible. Some of the mobile is automatically decreased when full power is not needed for accessories mentioned in this user guide, such as charger, headset, the call. The lower the power output, the lower the SAR value. or data cable, may be sold separately. Device models may have different versions and more than one value. Electrical Information of the Charger Component and design changes may occur over time and some changes could affect SAR values. The following electrical information corresponds to the above- mentioned charger models: For more info, go to www.sar-tick.com. Note that mobile devices may be transmitting even if you are not making a voice call. Input: 100-240 Vca 50-60 Hz 0-300 mA Your mobile device is also designed to meet the United States Output: 5,0 Vcc 0-2000 mA Federal Communications Commission (FCC) guidelines. FCC ratings Charger safety instructions for your device and more information on SAR can be found at http:/ The charger is suitable to be used only with compatible devices. /transition.fcc.gov/oet/rfsafety/sar.html. The charger should not be used in extremely high or low The World Health Organization (WHO) has stated that current temperatures. scientific information does not indicate the need for any special precautions when using mobile devices. If you are interested in Ventilation should not be obstructed by covering the charger with reducing your exposure, they recommend you limit your usage or use magazines, blankets, curtains etc. a hands-free kit to keep the device away from your head and body. Open flames, such as candles, should not be placed above the For more information and explanations and discussions on RF charger. exposure, go to the WHO website at www.who.int/peh-emf/en. The charger and the wall outlet shall be easily accessible at all times. In case the cable or the plugs are damage, stop using it. Copyrights and other notices The charger requires very low maintenance. If you want to clean it, use a dry cloth or a brush. FCC notice: Meaning of the symbols: This device complies with part 15 of the FCC rules. Operation is For internal use only subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any The charger should not be disposed as unsorted municipal interference received, including interference that may cause waste. It should be recycled. undesired operation. For more info, go to www.fcc.gov/engineering- technology/electromagnetic-compatibility-division/radio- The surface of the device is nickel-free. frequency-safety/faq/rf-safety. Any changes or modifications not expressly approved by HMD Global could void the user’s authority to Parts of the device are magnetic. Metallic materials may be attracted operate this equipment. Note: This equipment has been tested and to the device. Do not place credit cards or other magnetic stripe found to comply with the limits for a Class B digital device, pursuant cards near the device for extended periods of time, since the cards to part 15 of the FCC Rules. These limits are designed to provide may be damaged. reasonable protection against harmful interference in a residential Note: Pre-installed system software and apps use a significant installation. This equipment generates, uses and can radiate radio part of memory space. frequency energy and, if not installed and used in accordance with Keep a safe distance when using the flash. Do not use the flash on the instructions, may cause harmful interference to radio people or animals at close range. Do not cover the flash while taking communications. However, there is no guarantee that interference a photo. will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is Certification information encouraged to try to correct the interference by one or more of the following measures: (SAR) • Reorient or relocate the receiving antenna. This mobile device meets guidelines for exposure to radio waves as • Increase the separation between the equipment and receiver. set forth by the Federal Communications Commission (FCC). Refer to • Connect the equipment into an outlet on a circuit different from the following. that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC RF Exposure Information This device has an electronic label for certification information. To Your handset is a radio transmitter and receiver. It is designed and access it, select Settings > System > Certification. manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications © 2018 HMD Global. All rights reserved. HMD Global Oy is the Commission of the U.S. Government. The guidelines are based on exclusive licensee of the Nokia brand for phones & tablets. Nokia is a standards that were developed by independent scientific registered trademark of Nokia Corporation. organization through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless handsets employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1,6 W/kg. The tests are performed in


Document Created: 2019-03-23 10:11:49
Document Modified: 2019-03-23 10:11:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC