Test Report_DXX_ANT+_R2

FCC ID: 2AJOTTA-1087

Test Report

Download: PDF
FCCID_4157254

FCC Test Report Report No.: RF180523C09-8 R1 FCC ID: 2AJOTTA-1087 Test Model: TA-1087 Received Date: May 23, 2018 Test Date: Jun. 11, 2018 ~ Jun. 19, 2018 Issued Date: Oct. 24, 2018 Applicant: HMD Global Oy Address: Bertel Jungin aukio 9, 02600 Espoo, Finland Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) Test Location (1): No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan, R.O.C. Test Location (2): No.215, Sec. 3, Beixin Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C FCC Registration / 427177 / TW0011 Designation Number: This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF180523C09-8 R1 Page No. 1 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ........................................................................................................................... 4 2 Summary of Test Results ........................................................................................................................... 5 2.1 Measurement Uncertainty ..................................................................................................................... 5 2.2 Modification Record .............................................................................................................................. 5 3 General Information ................................................................................................................................... 6 3.1 General Description of EUT .................................................................................................................. 6 3.2 Description of Test Modes..................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 8 3.3 Description of Support Units ................................................................................................................. 9 3.3.1 Configuration of System under Test ........................................................................................... 9 3.4 General Description of Applied Standards ............................................................................................ 9 4 Test Types and Results ............................................................................................................................ 10 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 10 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 10 4.1.2 Test Instruments ........................................................................................................................ 11 4.1.3 Test Procedures ........................................................................................................................ 12 4.1.4 Deviation from Test Standard ................................................................................................... 12 4.1.5 Test Set Up ............................................................................................................................... 13 4.1.6 EUT Operating Conditions ........................................................................................................ 14 4.1.7 Test Results .............................................................................................................................. 15 4.2 Conducted Emission Measurement .................................................................................................... 20 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 20 4.2.2 Test Instruments ....................................................................................................................... 20 4.2.3 Test Procedures ........................................................................................................................ 20 4.2.4 Deviation from Test Standard ................................................................................................... 21 4.2.5 Test Setup ................................................................................................................................. 21 4.2.6 EUT Operating Conditions ........................................................................................................ 21 4.2.7 Test Results .............................................................................................................................. 22 4.3 20 dB Bandwidth Measurement.......................................................................................................... 24 4.3.1 Limits of 20 dB Bandwidth Measurement ................................................................................. 24 4.3.2 Test Setup ................................................................................................................................. 24 4.3.3 Test Instruments ....................................................................................................................... 24 4.3.4 Test Procedure ......................................................................................................................... 24 4.3.5 Deviation from Test Standard ................................................................................................... 24 4.3.6 EUT Operating Conditions ........................................................................................................ 24 4.3.7 Test Result ................................................................................................................................ 25 5 Pictures of Test Arrangements................................................................................................................ 26 Appendix – Information on the Testing Laboratories ................................................................................ 27 Report No.: RF180523C09-8 R1 Page No. 2 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

Release Control Record Issue No. Description Date Issued RF180523C09-8 Original Release Jun. 28, 2018 RF180523C09-8 R1 Revise applicant’s address Oct. 24, 2018 Report No.: RF180523C09-8 R1 Page No. 3 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

1 Certificate of Conformity Product: Smart Phone Brand: NOKIA Test Model: TA-1087 Sample Status: Production Unit Applicant: HMD Global Oy Test Date: Jun. 11, 2018 ~ Jun. 19, 2018 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.249) ANSI C63.10: 2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Oct. 24, 2018 Ivonne Wu / Supervisor Approved by : , Date: Oct. 24, 2018 Dylan Chiou / Project Engineer Report No.: RF180523C09-8 R1 Page No. 4 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

ooocc 2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.249) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is —14.75 dB at 0.17328 MHz. Radiated Emission Test 15.209 B.an.d Edge Measurement Meet the requirement of limit. 15.249 Limit: 50 dB less than the peak Pass Minimum passing margin is —14.47 dB 15.249 (d) value of fundamental frequency or at 937 MHz. meet radiated emission limit in section 15.209 15.215 (c) 20 dB Bandwidth Pass Meet the requirement of limit. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16—4—2: Expended Uncertainty Measurement Frequenc quency (k=2) (4) Conducted Emissions at mains ports 150 kHz ~ 30 MHz 244 dB 30 MHz ~ 200 MHz 2.0153 dB Radiated Emissions up to 1 GHz 200 MHz ~ 1000 MHz 2.0224 dB 1 GHz ~ 18 GHz 1.0121 dB Radiated Emissions above 1 GHz 18 GHz ~ 40 GHz 1.1508 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF180523C09—8 R1 Page No. 5 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF1805230C09—8 dated on Jun. 28, 2018

3 General Information 3.1 General Description of EUT Product Smart Phone Brand NOKIA Test Model TA-1087 Status of EUT Production Unit 5.0 Vdc or 9 Vdc or 12 Vdc (adapter) Power Supply Rating 5.0 Vdc (host equipment) 3.85 Vdc (Li-ion battery) Modulation Type GFSK Operating Frequency 2403 ~ 2480 MHz Number of Channel 78 Antenna Type PIFA antenna with -1.5 dBi gain Antenna Connector N/A Accessory Device Refer to Note as below Data Cable Supplied Refer to Note as below Note: 1. The EUT’s accessories list refers to Ext. Pho. 2. The above EUT information is declared by manufacturer and for more detailed features description, please refers to the manufacturer's specifications or user's manual. Report No.: RF180523C09-8 R1 Page No. 6 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

3.2 Description of Test Modes 78 channels are provided to this EUT: Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) 1 2403 21 2423 41 2443 61 2463 2 2404 22 2424 42 2444 62 2464 3 2405 23 2425 43 2445 63 2465 4 2406 24 2426 44 2446 64 2466 5 2407 25 2427 45 2447 65 2467 6 2408 26 2428 46 2448 66 2468 7 2409 27 2429 47 2449 67 2469 8 2410 28 2430 48 2450 68 2470 9 2411 29 2431 49 2451 69 2471 10 2412 30 2432 50 2452 70 2472 11 2413 31 2433 51 2453 71 2473 12 2414 32 2434 52 2454 72 2474 13 2415 33 2435 53 2455 73 2475 14 2416 34 2436 54 2456 74 2476 15 2417 35 2437 55 2457 75 2477 16 2418 36 2438 56 2458 76 2478 17 2419 37 2439 57 2459 77 2479 18 2420 38 2440 58 2460 78 2480 19 2421 39 2441 59 2461 20 2422 40 2442 60 2462 Report No.: RF180523C09-8 R1 Page No. 7 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable To Description Mode RE1G RE<1G PLC APCM - √ √ √ √ - RE1G: Radiated Emission above 1 GHz & Where RE<1G: Radiated Emission below 1 GHz Bandedge Measurement PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement NOTE: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Y-plane. Radiated Emission Test (Above 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Available Channel Tested Channel Modulation Type - 1 to 78 1, 39, 78 GFSK Radiated Emission Test (Below 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Tested Channel Modulation Technology Modulation Type - 1 to 78 1 GFSK Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Tested Channel Modulation Technology Modulation Type - 1 to 78 1 GFSK Antenna Port Conducted Measurement: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Tested Channel Modulation Technology Modulation Type - 1 to 78 1 GFSK Report No.: RF180523C09-8 R1 Page No. 8 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

ooocc Test Condition: Applicable To Environmental Conditions Input Power Tested By REz1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Charles Hsiao RE<1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Charles Hsiao PLC 25 deg. C, 68 % RH 120 Vac, 60 Hz Jisyong Wang APCM 25 deg. C, 68 % RH 3.85 Vde Carlos Chen 3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. 3.3.1 Configuration of System under Test w_ SS EUT (Power from AC Adapter) *Test Table 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.249) ANSI C63.10—2013 All test items have been performed and recorded as per the above standards. Report No.: RF180523C09—8 R1 Page No. 9 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF1805230C09—8 dated on Jun. 28, 2018

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement The field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following Field Strength of Fundamental Field Strength of Harmonics Fundamental Frequency (millivolts/meter) (microvolts/meter) 902 ~ 928 MHz 50 500 2400 ~ 2483.5 MHz 50 500 5725 ~ 5875 MHz 50 500 24 ~ 24.25 GHz 250 2500 Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits as below table, whichever is the lesser attenuation Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000 MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF180523C09-8 R1 Page No. 10 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

4.1.2 Test Instruments Description & Date of Due Date of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver N9038A MY52260177 Jul. 05, 2017 Jul. 04, 2018 Agilent Technologies Spectrum Analyzer FSU43 101261 Jan. 11, 2018 Jan. 10, 2019 ROHDE & SCHWARZ Double Ridge Guide Horn 3115 5619 Nov. 30, 2017 Nov. 29, 2018 Antenna EMCO BILOG Antenna VULB 9168 9168-153 Dec. 06, 2017 Dec. 05, 2018 SCHWARZBECK Fixed Attenuator BW-N10W5+ NA Jul. 07, 2017 Jul. 06, 2018 Mini-Circuits Loop Antenna EM-6879 269 Aug. 11, 2017 Aug. 10, 2018 Preamplifier 310N 187226 Jun. 23, 2017 Jun. 22, 2018 Agilent Preamplifier 83017A MY39501357 Jun. 23, 2017 Jun. 22, 2018 Agilent Power Meter ML2495A 1012010 Aug. 15, 2017 Aug. 14, 2018 Anritsu Power Sensor MA2411B 1315050 Aug. 15, 2017 Aug. 14, 2018 Anritsu Cable-CH1-01(RFC RF signal cable -SMS-100-SMS-12 5D-FB Jun. 26, 2017 Jun. 25, 2018 ETS-LINDGREN 0+RFC-SMS-100-S MS-400) RF signal cable Cable-CH1-02(RFC 8D-FB Jun. 26, 2017 Jun. 25, 2018 ETS-LINDGREN -SMS-100-SMS-24) Boresight Antenna Fixture FBA-01 FBA-SIP01 NA NA Software E3 NA NA NA BV ADT 8.130425b Antenna Tower NA NA NA NA MF Turn Table NA NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HsinTien Chamber 1. 3. The horn antenna and preamplifier (model: 83017A) are used only for the measurement of emission frequency above 1GHz if tested. 4. The IC Site Registration No. is IC7450I-1. Report No.: RF180523C09-8 R1 Page No. 11 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

4.1.3 Test Procedures For Radiated Emission below 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Both Parallel, perpendicular, and ground-parallel orientations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9 kHz at frequency below 30 MHz. For Radiated Emission above 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for 30 MHz ~ 1 GHz) / 1.5 meters (for above 1 GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detected function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for Quasi-peak detection (QP) at frequency below 1 GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1 GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98 %) or 10 Hz (Duty cycle ≥ 98 %) for Average detection (AV) at frequency above 1 GHz. (RBW = 1 MHz, VBW = 10 Hz) 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF180523C09-8 R1 Page No. 12 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

4.1.5 Test Set Up <Radiated Emission below 30 MHz> 1m EUT& 3m Support Units Turn Table 80 cm Ground Plane Test Receiver <Radiated Emission 30 MHz to 1 GHz> Ant. Tower 1-4m Variable 3m 10m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver Report No.: RF180523C09-8 R1 Page No. 13 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

<Radiated Emission above 1 GHz> Ant. Tower 1-4 m Variable EUT& 3m Support Units Turn Table Absorber 150 cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF180523C09-8 R1 Page No. 14 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

4.1.7 Test Results Above 1 GHz WORST-CASE DATA: EUT Test Condition Measurement Detail Channel Channel 1 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antenna Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2374 33.81 32.15 54 -20.19 31.78 5.37 35.49 207 155 Average 2374 55.83 54.17 74 -18.17 31.78 5.37 35.49 207 155 Peak 2403 60.64 58.9 94 -33.36 31.81 5.4 35.47 207 155 Average 2403 82.66 80.92 114 -31.34 31.81 5.4 35.47 207 155 Peak 2488 32.81 30.8 54 -21.19 31.9 5.53 35.42 207 155 Average 2488 54.83 52.82 74 -19.17 31.9 5.53 35.42 207 155 Peak Antenna Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2366 33.57 31.93 54 -20.43 31.76 5.37 35.49 100 134 Average 2366 55.59 53.95 74 -18.41 31.76 5.37 35.49 100 134 Peak 2403 62.04 60.3 94 -31.96 31.81 5.4 35.47 100 134 Average 2403 84.06 82.32 114 -29.94 31.81 5.4 35.47 100 134 Peak 2484 34.32 32.36 54 -19.68 31.88 5.5 35.42 100 134 Average 2484 56.34 54.38 74 -17.66 31.88 5.5 35.42 100 134 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.1585 ms * 50 / 100 ms) = -22.02 dB Please refer to the plotted duty Report No.: RF180523C09-8 R1 Page No. 15 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

EUT Test Condition Measurement Detail Channel Channel 39 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antenna Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2388 34 32.29 54 -20 31.8 5.4 35.49 207 155 Average 2388 56.02 54.31 74 -17.98 31.8 5.4 35.49 207 155 Peak 2441 60.69 58.82 94 -33.31 31.85 5.46 35.44 207 155 Average 2441 82.71 80.84 114 -31.29 31.85 5.46 35.44 207 155 Peak 2490 34.05 32.04 54 -19.95 31.9 5.53 35.42 207 155 Average 2490 56.07 54.06 74 -17.93 31.9 5.53 35.42 207 155 Peak Antenna Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2360 32.99 31.36 54 -21.01 31.76 5.37 35.5 100 134 Average 2360 55.01 53.38 74 -18.99 31.76 5.37 35.5 100 134 Peak 2441 62.06 60.19 94 -31.94 31.85 5.46 35.44 100 134 Average 2441 84.08 82.21 114 -29.92 31.85 5.46 35.44 100 134 Peak 2498 33.73 31.71 54 -20.27 31.9 5.53 35.41 100 134 Average 2498 55.75 53.73 74 -18.25 31.9 5.53 35.41 100 134 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.1585 ms * 50 / 100 ms) = -22.02 dB Please refer to the plotted duty Report No.: RF180523C09-8 R1 Page No. 16 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

EUT Test Condition Measurement Detail Channel Channel 78 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antenna Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2390 32.94 31.21 54 -21.06 31.8 5.4 35.47 207 115 Average 2390 54.96 53.23 74 -19.04 31.8 5.4 35.47 207 115 Peak 2480 60.26 58.3 94 -33.74 31.88 5.5 35.42 207 115 Average 2480 82.28 80.32 114 -31.72 31.88 5.5 35.42 207 115 Peak 2492 33.4 31.38 54 -20.6 31.9 5.53 35.41 207 115 Average 2492 55.42 53.4 74 -18.58 31.9 5.53 35.41 207 115 Peak Antenna Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2384 33.98 32.29 54 -20.02 31.78 5.4 35.49 100 134 Average 2384 56 54.31 74 -18 31.78 5.4 35.49 100 134 Peak 2480 62.01 60.05 94 -31.99 31.88 5.5 35.42 100 134 Average 2480 84.03 82.07 114 -29.97 31.88 5.5 35.42 100 134 Peak 2498 33.25 31.23 54 -20.75 31.9 5.53 35.41 100 134 Average 2498 55.27 53.25 74 -18.73 31.9 5.53 35.41 100 134 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. The average value of fundamental frequency is: Average = Peak value + 20log(Duty cycle) Where the duty factor is calculated from following formula: 20 log (Duty cycle) = 20 log (0.1585 ms * 50 / 100 ms) = -22.02 dB Please refer to the plotted duty Report No.: RF180523C09-8 R1 Page No. 17 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

Below 1 GHz WORST-CASE DATA: EUT Test Condition Measurement Detail Channel Channel 1 Frequency Range 30 MHz ~ 1 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Quasi-peak (QP) Environmental 25 deg. C, 65 % RH Tested By Charles Hsiao Conditions Antenna Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 88.59 17.7 38.45 43.5 -25.8 9.95 1.11 31.81 172 115 Peak 155.55 20.63 42.82 43.5 -22.87 8.56 1.52 32.27 196 34 Peak 277.59 19.9 37.28 46 -26.1 12.71 2.03 32.12 176 224 Peak 373.5 22.74 38.11 46 -23.26 14.51 2.26 32.14 184 117 Peak 722.8 20.95 30.36 46 -25.05 19.54 3.16 32.11 156 224 Peak 937 29.35 35.29 46 -16.65 21.65 3.62 31.21 163 219 Peak Antenna Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 49.71 19.33 36.1 40 -20.67 14.55 0.9 32.22 187 115 Peak 87.24 16.52 37.57 40 -23.48 9.7 1.11 31.86 186 263 Peak 157.17 15.67 37.78 43.5 -27.83 8.64 1.52 32.27 123 107 Peak 381.9 18.45 33.65 46 -27.55 14.63 2.34 32.17 112 175 Peak 584.9 20.53 32.2 46 -25.47 17.71 2.82 32.2 140 286 Peak 937 31.53 37.47 46 -14.47 21.65 3.62 31.21 186 350 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value Report No.: RF180523C09-8 R1 Page No. 18 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

<Duty Cycle Correction Factor> Duty Factor on time/100 ms (One Pulse) Plot on Channel 1 Duty Factor on time/100 ms (Count Pulse) Plot on Channel 1 20 log (Duty cycle) = 20 log (0.1585 ms * 50 / 100 ms) = -22.02 dB Report No.: RF180523C09-8 R1 Page No. 19 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-Peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 4.2.2 Test Instruments Description & Date of Due Date of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver ESCI 100613 Nov. 23, 2017 Nov. 22, 2018 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond1-01 Sep. 05, 2017 Sep. 04, 2018 Woken LISN/AMN ROHDE & SCHWARZ ESH3-Z5 835239/001 Mar. 06, 2018 Mar. 05, 2019 (EUT) LISN/AMN ROHDE & SCHWARZ ESH3-Z5 100311 Aug. 15, 2017 Aug. 14, 2018 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.4 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. 4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50 uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit – 20 dB) was not recorded. Note: The resolution bandwidth and video bandwidth of test receiver is 9 kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15 MHz - 30 MHz. Report No.: RF180523C09-8 R1 Page No. 20 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

ommert [vexiras)] 4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane / Test Receiver EUT o o 0 o 40cm U i5 a o o 80cm LISN L L L N T \ Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF180523C09—8 R1 Page No. 21 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF1805230C09—8 dated on Jun. 28, 2018

3) ommert 4.2.7 Test Results Detector Function & . . Quasi—Peak (QP) / Frequency Range 150kHz ~ 30MHz Resolution Bandwidth Average (AV), 9kHz Environmental s Input Power 120Vac, 60Hz Conditions 25°C, 65%RH Tested by Jisyong Wang Test Date 2018/6/14 Phase Of Power : Line (L) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16967 10.10 87.99 23.79 48.09 33.89 64.98 54.98 —16.89 —21.09 2 0.55679 10.12 30.60 18.14 40.72 28.26 56.00 46.00 —15.28 —17.74 3 0.76789 10.13 19.85 7.80 29.98 17.93 56.00 46.00 —26.02 —28.07 4 1.62798 10.17 21.83 8.01 8200 18.18 56.00 46.00 —24.00 —27.82 5 242171 10.21 20.77 8.32 30.98 18.53 56.00 46.00 —25.02 —27.47 6 11.45381 10.71 19.02 6.48 29.73 17.19 60.00 50.00 —30.27 —32.81 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF180523C09—8 R1 Page No. 22 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF1805230C09—8 dated on Jun. 28, 2018

3) ommert Detector Function & . Frequency Range 150kHz ~ 3OMHz Resolution S:‘:;"Ze(fvgogzéz Bandwidth 9 B Environmental s o Input Power 120Vac, 60Hz Conditions 25°C, 65%RH Tested by Jisyong Wang Test Date 2018/6/14 Phase Of Power : Neutral (N) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) a.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 0.17328 10.10 39.95 24.41 50.05 34.51 64.80 54.80 —14.75 —20.29 —+ 0.19255 10.10 33.66 16.21 43.76 26.31 63.93 53.93 —20.17 —27.62 No 0.58792 10.12 15.72 1.87 25.84 11.99 56.00 46.00 —30.16 —34.01 c3 0.58792 10.12 24.46 10.96 34.58 21.08 56.00 46.00 —21.42 —24.92 & 1.55760 10.16 17.11 1.50 27.27 11.66 56.00 46.00 —28.73 —34.34 &n 6 6.31998 10.36 21.93 8.01 8229 18.37 60.00 50.00 —27.71 —31.63 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF180523C09—8 R1 Page No. 28 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF1805230C09—8 dated on Jun. 28, 2018

4.3 20 dB Bandwidth Measurement 4.3.1 Limits of 20 dB Bandwidth Measurement Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §§ 15.217 through 15.257 and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. 4.3.2 Test Setup EUT Spectrum Analyzer Attenuator 4.3.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.4 Test Procedure a. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. b. Turn on the EUT and connect it to measurement instrument. Then set it to any one convenient frequency within its operating range. Set a reference level on the measuring instrument equal to the highest peak value. c. Measure the frequency difference of two frequencies that were attenuated 20dB from the reference level. Record the frequency difference as the emission bandwidth. d. Repeat above procedures until all frequencies measured were complete. 4.3.5 Deviation from Test Standard No deviation. 4.3.6 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at channel frequencies individually. Report No.: RF180523C09-8 R1 Page No. 24 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

4.3.7 Test Result Channel Frequency (MHz) 20 dB Bandwidth (MHz) Pass / Fail 1 2403 2.402278846 Pass Spectrum Plot of Worst Value Report No.: RF180523C09-8 R1 Page No. 25 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF180523C09-8 R1 Page No. 26 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF180523C09-8 R1 Page No. 27 / 27 Report Format Version: 6.1.1 Cancels and replaces the report no.: RF180523C09-8 dated on Jun. 28, 2018


Document Created: 2019-09-09 03:53:27
Document Modified: 2019-09-09 03:53:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC