Test report HAC part 2

FCC ID: 2AJOTTA-1084

Test Report

Download: PDF
FCCID_3893587















簿 Ｏ Calibration Laboratory of S Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d'etalonnage c Engin^ering AG Servizio svizzero ditaratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accreditation No.: SCS 0108 Accredited b!y the Swiss Accreditation Service (SAS) The Swiss /^ccreditation Service is one ofthe signatories to the EA Multilateral Agreementforthe recognition of calibration certificates certificat e No ER3-2528_Jan18 client "凑２528 一一Ｈ Object close nearfield 瑚 Calibration!;date This calibration cer "一田饿 tificate documents the traceability to national standards, which realize the physical units of measurements (SI). The meas^rements and the uncer tainties with confidence probability are given on the following pages and are par t ofthe cer All calibrations have been conducted in the closed laboratory facility: environmenttemperature (22 3)C and humidity < 70%. Calibration;Equipment used (M&TE criticalfor calibration) tificate Cal Date (Cer tificate No Scheduled Calibration Primary Standards ID SN:104778 O4-Apr-17 (No. 217-02521/02522) Apr-18 Power meterNRP SN:103244 04-Apr-17 (No. 217-02521) Apr-18 Power sensor NRP-Z91 SN: 103245 04-Apr-17 (No^217-02525) Apr-18 Power sensor NRP-Z91 SN: S5277 (20x) 07-Apr-17 (No, 217-02528) Apr-18 Reference 20 dB Attenuator SN: 2328 lo-Oct-17 (No. ER3-2328_Oct17) Oct-18 Reference Probe ER3DV6 2-Aug-17 (No. DAE4-789_Aug17) Aug-18 DAE4 SN: 789 Check Date (in house) Scheduled Check Secondary Standards ID 06-Apr-16 (in house check Jun-16) In house check: Jun-18 Power meter E4419B SN: GB41293874 06-Apr-16 (in house check Jun-16) In house check: Jun-18 Power sensor E4412A SN: MY41498087 06-Apr-16 (in house check Jun-16) In house check: Jun-18 Power sensor E4412A SN: 000110210 04-Aug-99 (in house check Jun-16) In house check: Jun-18 RF generator HP 8648C SN: US3642U01700 18-Oct-01(in house check Oct-17) In house check: Oct-18 Network Analyzer HP 8753E SN: US37390585 Calibrated by Approved; by Issued: January 24, 2018 This calibration cer tificate shall not be reproduced exceptin full without writ ten approval ofthe laboratory Certificate No: ER3-2528_Jan18 Page i of10

簿Ｑ Calibration Laboratory of ^^<^ S Schweizerischer Kalibrierdienst Schmid & Partner ll* ii c Service suisse d'etalonnage Engineering AG ! ?-@ Servizio svizzero ditaratura Zeughausstiasse 43, 8004 Zurich, Switzerland ^//?-\ S Swiss Calibration Service : ""/iilii^ ｜︒｜ j; : Accreditation No.: SCS 0108 ¡£ Accredited tiy the he Swiss Accreditation Service (SAS) t 目 ３ ０ The Swiss Accreditation Service is one ofthe signatories to the EA S c ed t t ｜ ９ 了 Multilateral Agreementforthe recognition of calibration certificates 肛｜ a r Glossary: NORMx.y X yz sensitivity in free space £¬ DCP i diode compression point CF |! crestfactor(1/duty_cycle) ofthe RF signal A, B, C, DJ modulation dependentlinearization parameters Polarization cp cp rotation around probe axis S rotation around an axis thatis in the plane normalto probe axis (at measurement center), Polarization 9 甲 i.e., 9 = 0 is normalto probe axis information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1309-2005," IEEE Standard for calibration of electromagnetic field sensors and probes, excluding antennas,from 9 kHz to 40 GHz", December 2005 b) CJtlA Test Plan for Hearing Aid Compatibility, Rev 3.0, November 2013 j: Methods Applied and Interpretation of Parameters: @ ^iORMx,y,z: Assessed for E-field polarization 9 = 0 for XY sensors and ^ = 90 for Z sensor(f < 900 MHz in TEM-cell;f > 1800 MHz: R22 waveguide). @ NORM(f)x,y,z = N0RMx,y,z * frequency_response (see Frequency Response Chart). @ DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW Signal(no uncertainty required). DCP does not depend on frequency nor media. j" @ IfAR: PAR is the Peak to Average Ratio thatis not calibrated but determined based on the signal characteristics @ Ax,y,z; Bx,y,z; Cx,y,z; Dx,y,z; VRx,y,z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. @ Sphericalisotropy (3D deviation from isotropy): in a locally homogeneous field realized using an open waveguide setup. Sensor Offset: The sensor offset corresponds to the offset of virtual measurement centerfrom the probe tip (on probe axis). No tolerance required. ConnectorAngle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: ER3-2528_Jan18 Page 2 of10


QPSK) 16-QAM) QPSK) January 24, 2018 f Probe: ER3DV6 - SN:2528 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (ny/(V/m)2) ４ 86 ４ 58 1.82 10.1 % 98.5 99.8 98.0 DCP (nWj" Modulation Calibration Parameters UID Communication System Name A c VR unc dBvVV dB mV (k=2) B d 0.00 181.2 3.0 % X 0.0 0.0 亏0 0 I cw ｜ 0.0 1.0 202.1 Y 0.0 203.6 ｜ z 0.0 0.0 1.0 ＠ 29.0 9.39 114.0 2.2 % 10021- GSM-FDD (TDMA, GMSK) X 22.77 99.2 DAC I 140.1 Y 25.76 99.7 29.1 ＠ １ ｜ 99.5 29.6 108.4 z 28.14 33.5 9.21 128.6 3.8 % 88.4 10啤72- | LTE-TDD (SC-FDMA, 1 RB, 20 MHz, X 12.73 CAD · 103.3 Y 9.59 78.3 28 叮 80.4 28.4 112.0 z 11.20 33.6 9.48 130.7 3.5 % 10173- LTE-TDD (SC-FDMA, 1 RB, 20 MHz, X 13.23 88.7 CAD 104.7 Y 10.02 78.8 28.4 28.9 113.3 z 11.82 8叮 2 33.7 9.48 130.9 3.8 % 10238- LTE-TDD (SC-FDMA, 1 RB, 15 MHz, X 13.35 88.9 CAD ! 79.4 28.7 104.9 ： Y 10.21 8叮 3 29.0 口口33 z 11.82 33.4 9.21 129.2 +3.8 % 10240- LTE-TDD (SC-FDMA, 1 RB, 15 MHz, X 12.75 88.3 CAD 103.2 Y 9.56 78.4 28.1 80.5 28.5 112.1 z 11.23 口2.49 99.7 +3.0 % 10295- CDMA2000, RC1, S03, 1/8th Rate 25 fr X 17.57 98.8 40.口 AAB 124.1 Y 18.97 99.2 39.6 99.3 38.8 139.8 z 21.36 tis stated as the standard uncertainty of measurement B Numericallinearization parameter: uncertainty notrequired. E Uncertainty is determined using the max. deviation from linearresponse applying rectangular distribution and is expressed forthe square ofthe field value! Cer tificate No: ER3-2528_Jan18 Page 4 of10

ry 24, 2018 Certificate No: ER3-2528_Jan18 Page 5 of10


Receiving Pattern (([>), ^ = 0 Certificate No: ER3-2528_Jan18 Page 7 of10

10 January 24, 2018 ER3DV6-SN:2528 Dynamic Range f(E-field) (TEM cell ,f = 900 MHz) los 105 A [ l ] s i i n u e i B d 叩02 10 03 2 @ 吾 L 0 e 田 L 巧 臣 叩 101 o^ 0 E total[V/m] not compensated compensated Uncertainty of Linearity Assessment: 0.6% (k=2) Certificate No: ER3-2528_Jan18 Page 8 of10

January 24, 2018 Deviation from Isotropy in Air Error(<|>, 3),f = 900 MHz 0 0.0 0.2 0.4 0.6 0.8 l·0 Certificate No: ER3-2528_Jan18 Page 9 of10

January 24, 2018 ER3DV6 - SN:2528 DASY/EASY - Parameters of Probe: ER3DV6 - SN:2528 Other Probe Parameters Sensor Arrangement Rectangular 18.4 Connector Angle ( ) Mechanical Sur face Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm lo mm Probe Body Diameter lo mm Tip Length a mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 2.5 mm Probe Tip to Sensor Y Calibration Point 2.5 mm Probe Tip to Sensor Z Calibration Point Certificate No: ER3-2528_Jan18 Page lo of10


Document Created: 2018-06-13 15:22:34
Document Modified: 2018-06-13 15:22:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC