User manual

FCC ID: 2AJOTTA-1046

Users Manual

Download: PDF
FCCID_3791971

Microphone Audio connector Main cameras Get Started Nokia 7 plus Fingerprint Flash Proximity sensor sensor Earpiece SIM card/ MicroSD card Front camera Charger connector Loudspeaker Microphone Volume keys Power/Lock key TA-1055 / TA-1046 1. Insert the SIM and memory 2. Charge the battery and switch 3. Learn more about your new card the phone on Nokia phone 1. Open the SIM and memory card tray by putting Plug a compatible charger into a wall outlet, and For an online user guide and troubleshooting help, the provided tray opener into the hole next to the connect the cable to your phone. Your phone go to www.nokia.com/mobile-support. tray. supports the USB-C cable. You can also charge your 2. Put the nano-SIM into slot 1 located on the tray phone from a computer with a USB cable, but it may with the contact area face down. If you have a dual take a longer time. SIM variant, you can either put a second SIM or a If the battery is completely discharged, it may take memory card into slot 2. If you have a single SIM several minutes before the charging indicator is variant, you can only put a memory card into slot 2. displayed. 3. Slide the SIM and memory card tray back into place. To switch your phone on, press and hold the power Use only original nano-SIM cards. Use of key until the phone vibrates. The phone guides you incompatible SIM cards may damage the card or the through the setup. device, and may corrupt data stored on the card. Note: On dual SIM capable devices, both SIM1 and SIM2 slots support 4G networks. However, if your SIM1 and SIM2 are both LTE SIM cards, the primary SIM supports 4G/3G/2G networks, while the secondary SIM can only support 3G/2G. For more information on your SIM cards, contact your service provider. USB-C USB micro-B PKB2N55049A V1.0 xxxxxxxxxx

Product and safety info of age and health. The guidelines use a unit of measurement known as the Specific Absorption Rate, or SAR. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Important: For important info on the safe use of your device and • Consult the dealer or an experienced radio/TV technician for help. battery, read the Product and safety info booklet before you take The SAR limit for mobile devices is 2.0 W/kg and the highest SAR your device into use. value for this device when tested at the ear is 0.361 W/kg*. As mobile devices offer a range of functions, they can be used in other Qualcomm and Snapdragon are trademarks of Qualcomm You can only use your device on the GSM 850/900/1800/1900; positions, such as on the body. In this case, the highest tested SAR Incorporated, registered in the United States and other countries. WCDMA Band 1, 2, 5, 8; LTE Band 1, 3, 5, 7, 8, 20, 28, 38, 40, 41 (Full value is 1.776 W/kg* at the separation distance of 0.5 cm from the band 41) networks. You need a subscription with a service provider. body. ZEISS, the ZEISS logo, Tessar and T* are registered trademarks of Important: 4G/LTE might not be supported by your network Carl Zeiss AG used under license of Carl Zeiss Vision GmbH. For electronic safety, maintain the separation distance with service provider or by the service provider you are using when accessories containing no metal, that position handset a minimum of traveling. In these cases, you may not be able to make or receive © 2018 HMD Global. All rights reserved. HMD Global Oy is the the above distance. Use of other accessories may not ensure exclusive licensee of the Nokia brand for phones & tablets. Nokia is a calls, send or receive messages or use mobile data connections. To compliance with RF exposure guidelines. make sure your device works seamlessly when full 4G/LTE service is registered trademark of Nokia Corporation. not available, it is recommended that you change the highest *The tests are carried out in accordance with international guidelines connection speed from 4G to 3G. To do this, on the home screen, tap for testing. Settings > Network & Internet > Mobile network, and switch This mobile device meets guidelines for exposure to radio waves as Preferred network type to 2G/3G. set forth by the Federal Communications Commission (FCC). Refer to For more info, contact your network service provider. the following. Maximum transmit power FCC RF Exposure Information Your handset is a radio transmitter and receiver. It is designed and GSM 850 32.5 dBm manufactured not to exceed the emission limits for exposure to GSM 900 32.5 dBm radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The guidelines are based on DCS 1800 29.5 dBm standards that were developed by independent scientific PCS 1900 29.5 dBm organization through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed WCDMA FDD I 23 dBm to assure the safety of all persons, regardless of age and health. The WCDMA FDD II 23 dBm exposure standard for wireless handsets employs a unit of measurement known as the Specific Absorption Rate, or SAR. The WCDMA FDD V 23 dBm SAR limit set by the FCC is 1.6 W/kg. The tests are performed in WCDMA FDD VIII 23 dBm positions and locations (e.g. at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this LTE Band 1 23 dBm model handset as reported to the FCC when tested for use at the ear LTE Band 2 23 dBm is 0.68 W/kg, and when worn on the body in a holder or carry case, is 0.62 W/kg. LTE Band 3 23 dBm Body-worn Operation; This device was tested for typical body-worn LTE Band 5 23 dBm operations with the handset kept 1.5 cm from the body. To maintain LTE Band 7 23 dBm compliance with FCC RF exposure requirements, use accessories that maintain a 1.5 cm separation distance between the user’s body and LTE Band 8 23 dBm the handset. The use of belt clips, holsters and similar accessories LTE Band 20 23 dBm should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply LTE Band 28 23 dBm with FCC RF exposure requirements, and should be avoided. The FCC LTE Band 38 23 dBm has granted an Equipment Authorization for this model handset with all reported SAR levels evaluated as in compliance with the FCC RF LTE Band 40 23 dBm emission guidelines. SAR information on this model handset is on file LTE Band 41 23 dBm with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/ after searching on FCC ID 2AJOTTA-1055 and Bluetooth 7 dBm FCC ID 2AJOTTA-1046. WLAN 2.4 G 16 dBm Additional information on Specific Absorption Rates (SAR) can be found on the FCC website at www.fcc.gov/general/radio-frequency- WLAN 5 G 14 dBm safety-0. NFC 420 mW To send data or messages, a good connection to the network is ANT+ 0 dBm needed. Sending may be delayed until such a connection is available. Follow the separation distance instructions until the sending is Your device has an internal, non-removable rechargeable battery. Do finished. not attempt to remove the battery, as you may damage the device. During general use, the SAR values are usually well below the values To replace the battery, take the device to the nearest authorised stated above. This is because, for purposes of system efficiency and service facility. to minimise interference on the network, the operating power of Charge your device with the FC0300 (EU plug) / FC0301 (UK plug) / your mobile is automatically decreased when full power is not needed FC0302 (US Plug) / FC0303 (Australia plug) / FC0311 (India Plug) or for the call. The lower the power output, the lower the SAR value. the AD-18WE (EU Plug) / AD-18WX (UK plug) / AD-18WU (US plug) / Device models may have different versions and more than one value. AD-18WN (India Plug) charger, depending on the plug type of your Component and design changes may occur over time and some country. HMD Global may make additional battery or charger models changes could affect SAR values. available for this device. Charging time can vary depending on device capability. Third-party chargers that comply with the applicable USB For more info, go to www.sar-tick.com. Note that mobile devices requirements, and that can connect to your device USB connector, may be transmitting even if you are not making a voice call. may also be compatible. Some of the accessories mentioned in this This device has an electronic label for certification information. To user guide, such as charger, headset, or data cable, may be sold access it, select Settings > System > About Phone > Certification. separately. Note: The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range in the following countries: Copyrights and other notices AT BE BG HR CY CZ DK Declaration of Conformity Hereby, HMD Global Oy declares that this product is in EE FI FR DE EL HU IE compliance with the essential requirements and other IT LV LT LU MT NL PL relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be found at www.nokia.com/ PT RO SK SI ES SE UK mobile-declaration-of-conformity. The surface of the device is nickel-free. FCC notice: Use only compatible memory cards approved for use with this device. Incompatible cards may damage the card and the device and corrupt This device complies with part 15 of the FCC rules. Operation is data stored on the card. subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any Note: Pre-installed system software and apps use a significant interference received, including interference that may cause part of memory space. undesired operation. For more info, go to www.fcc.gov/engineering- Keep a safe distance when using the flash. Do not use the flash on technology/electromagnetic-compatibility-division/radio- people or animals at close range. Do not cover the flash while taking frequency-safety/faq/rf-safety. Any changes or modifications not a photo. expressly approved by HMD Global could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant Certification information to part 15 of the FCC Rules. These limits are designed to provide (SAR) reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio This mobile device meets guidelines for exposure to radio waves as frequency energy and, if not installed and used in accordance with set forth by the Council of Europe (CE). Refer to the following. the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference European RF Exposure Information will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be Your mobile device is a radio transmitter and receiver. It is designed determined by turning the equipment off and on, the user is not to exceed the limits for exposure to radio waves recommended encouraged to try to correct the interference by one or more of the by international guidelines. These guidelines were developed by the following measures: independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.



Document Created: 2018-03-21 19:30:12
Document Modified: 2018-03-21 19:30:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC