I17Z60755-SEM05_SAR_Rev0_part5

FCC ID: 2AJOTTA-1021

RF Exposure Info

Download: PDF
FCCID_3430144

Measurement Conditions DASY system contiguration, as far as not iven on page 1 DASY Version nasys vsese Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Conter — TSL 10 mm with Spacer Zoom Scan Resolution ok, dy, dz =5 mm Frequency 1900 Mz a 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 220°C 40.0 1.40 mhoim Measured Head TSL parameters 20 £02)°C so826% 1.38 mho/im 6 % Head TL temperature change during test <os‘c en SAR result with Head TSL SAR averaged over 1 om" (1 g) of Head TL Condition SAR measured 250 mW input power 10.1 Wig SAR for nominal Head TSL paramoters normalized to 1W 40.7 Whkg # 17.0 % (ke2) SAR averaged over 10 om* (10 g) of Head TSL condition SAR measured 250 mW input power 5.28 Whg SAR for nominal Head TSL parameters normalized to 1W 21.2 Whey £16.5 % (ke2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 220°0 ses 1.52 mhom Measured Body TSL parametors g2002)°C 5276 % 1.51 mho/m +6 % Body TSL temperature change during test <as‘o — ~— SAR result with Body TSL SAR averaged over 1 om* (1 g) of Body TSL Condition SAR measured 250 mW input power 10.0 wikg SAR for nominal Body TSL parameters normalized to 1W 40.1 Whkg =17.0 % (ke2) SAR averaged over 10 om* (10 g) of Body TSL condition SAR measured 250 mW input power 5.42 Who SAR for nominal Body TL parametors normalized to 1W 21.3 Whkg £16.5 % (c=2) Certficate No: D1900V2—50101_Jult6 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance,transformed to feed point sosn+55jn Retum Loss +251 0B Antenna Parameters with Body TSL Impedance,transformed to feed point 4700 +670 Retum Loss —22.4 08 General Antenna Parameters and Design Electral Delay (one direction) 1.202 ns After long term use with 100W radiated power, only a sight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semiigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the ‘Measurement Condiions® paragraph. The SAR data are notaffected by this change. The overall dipole length is stll according to the Standard. No excessive force must be applied to the dipole arms, because thay might band or the soidered connections near the feedpoint may be damaged ional EUT Data Manufactured by sreaq Manufactured on March 28, 2008 Certficate No: D1900V2—5dt01_Jult6 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 22.07.2016 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz D1900V2; Type: D1900V2; Serial: D1900V2 — SN:5d101 Communication System: UID 0 — CW; Frequency: 1900 MHz Medium parameters used: f= 1900 MHz: 0 = 1.38 S/m; & = 39.8; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEEAEC/ANSI C63.19—2011) DASY52 Configuration: + Probe: EX3DV4 — SN7349; ConvF(7.99, 7.99, 7.99); Calibrated: 15.06.2016; Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronies: DAFA Sn601; Calibrated: 30.12.2015 Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7372) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x8x7)/Cube 0: Measurement grid: dx=Smm, dy=5mm, dz=mm Reference Value = 107.9 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 19.0 W/kg SAR(I g) = 10.1 W/kg; SAR(IO g) = 5.28 W/kg Maximum value of SAR (measured) = 15.8 Wkz & let— 5.00 —7.60 —1.40 15.20 —19.00 0 dB = 15.8 Wikg = 11.99 dBW/kg Certficate No: D1900V2—5d101_Jult Page 5 of 8

Impedance Measurement Plot for Head TSL 22 aur ress ssseosze c siun a ucss . sasa o aso.ar pa MBS 1 300.000 oohiz by i° ma ca ma Sriey 1 700.000 co0 miz srom 2 100.000 ooo mis Cortficate No: D19002.50101_.Jult6 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 28.07.2016 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz D1900V2; Type: D1900V2; Serial: D1900V2— SN: 5d101 Communication System: UID 0 — CW; Frequency: 1900 MHz Medium parameters used: {= 1900 MHz; a= 1.51 $/m; 6: = 52.7; p = 1000 kg/m Phantom section: Flat Section Mcasurement Standard: DASYS (IEEE/TIEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConyF(8.03, 8.03, 8.03); Calibrated: 15.06.2016; * Sensor—Surface; 1.4mm (Mechanical Surface Detection) * Electronics: DAEA Sn601: Calibrated: 30.12.2015 * Phantom: Flat Phantom 5.0 (back); Type: QDOOOPSOAA; Serial: 1002 * DASY52 52.8.8(1258); SEMCAD X 14.6.10(7372) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=3mm, dy=5mm, dz=3mm Reference Value = 104.2 V/m; Power Drift = —0.03 dB Peak SAR (extrapolated) = 17.6 W/kg SAR(L g) = 10 Wikgs SAR(1O g) = 5.32 Wig Maximum value of SAR (measured) = 15.0 W/ke 333 5.67 —10.00 413.3 —16.67 0 dB = 15.0 Wikg = 11.76 dBW/kg Certficate No: D1900V2—5d101_Jult6 Page 7 of 8

Impedance Measurement Plot for Body TSL 2e uin zers. oeszores gxn sn a ucss dranare . sropme seaos ph 1 00.000 c00 mtz e ivs is ma one ma Sther 1 ron.o00 oo fiz sTor 2 100.000 ono riz Certficate No: D1900V2—5d101_Jult6 Page 8 of 8

No. I17Z60755-SEM05 Page 157 of 207 2450 MHz Dipole Calibration Certificate ©Copyright. All rights reserved by CTTL.

® Calibration 4 Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Suitzeriand Aceredted by the Siss Accrediation Sorvice (BA8) & Schwelzerischer Kallorirdienst g Service suisse étalonnage 5. Servirlo aviezero ditaratura swiss Cabration Service Accrediation No.: SCS 0108 The Swiss Accredifaton Serviceis one ofthe signatorias tothe EA MullLateral Agreament for the recognition of callbrtion cortficates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy,z NA not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz), February 2005 c IEC 62209—2, "Procedure to determinethe Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)*, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions:Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedancestated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. + SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certficate No: D2450V2—053_Jult6 Page 2 of 8

m TTL m Measurement Conditions DASY system contiquration, as far as not given on page 1. DASY Version oasys vsess Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Conter — TSL 10 mm with Spacer Zoom Scan Resolution . dy, dz =5 mm Frequency 2450 MHza 1 Mz Head TSL parameters The following parameters and calculations were agplied. Temperature Permittivity Conductivity Nominal Head TSL parameters 220°0 so» 1.80 mhoim Measured Head TSL parameters @r002)°C 80.026% 1.88 mhoim=6 % Head TSL temperature change during test <05°C — SAR result with Head TSL SAR averaged over 1 om" (1 g) of Head TSL Condiion SAR measured 250 mW input power 135 Who SAR for nominal Head TSL parameters normalized to 1W 52.0 wikg 2 17.0 % (c=2) SAR averaged over 10 om* (10 g) of Head TSL condition SAR measured 250 mW input power 623 Wikg SAR for nominal Head TSL paramaters normalized to 1W 24.6 Wikg a16.5 % (k22) Body TSL parameters The folowing parameters and calculations were apoled. Temperature Permittivity Conductivity Nominal Body TSL parameters 220°C se.r 1.95 mhoim Measured Body TSL parameters (2.0 £02) °C 51826 % 203 mhoim 26 % Body TL temperature change during test <05°C m e SAR result with Body TSL SAR averaged over 1 om‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 18.1 Wig SAR for nominal Body TSL parameters normalized to 1W 51.2 Wikg x 17.0 % (kx2) SAR averaged over 10 om" (10 g) of Body TSL condition SAR measured 250 mW input power 5.10 wig SAR for nominal Body TSL paramaters normalized to 1W 2401 Wikg 216.5 % (k2) Cerificate No: D2450V2—853_.Jult6 Page 3 of 8

Appendix (Ade ional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point sern+s1in Return Loss —24.8 i8 Antenna Parameters with Body TSL Impedance, transformed to feed point soon+4s o Retur Loss —27.0 08 General Antenna Parameters and Design [ Electrical Detay (one direction) | 1.162 ns After long term use wih 100W radiated power, only a sight warming ofthe dipole near the feedpoint can be measured. The dipole is madle of standard semirigid coaxial cable. The center conductor of the feeding line is directly connacted to the second arm of the cipole. The antennais therefore short—circuited for DC—signals. On some of the dipolos, small end caps are added tothe dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditons‘ paragraph. The SAR data are not affected by this change. The overal dipole length is stit according to the Standard. No excessive force must be applied to the dipole arms, because thay might band or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by sreaq Manufactured on November 10, 2009 Cortficate No: D24502—853_.Jult Page 4 or 8


Document Created: 2017-06-13 14:20:54
Document Modified: 2017-06-13 14:20:54
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC