test report

FCC ID: 2AJGM-UV82

Test Report

Download: PDF
FCCID_3900037

® 52 \ /ss fll A\G %statiao:of gfllzal Ct%plia,r{;ejz Page 1 of 30 FCC Test Report Report No.: AGCO02294180601FEO8 FCC ID : —2AJGM—UV82 PRODUCT DESIGNATION : DUAL BAND F3E TRANSCEIVER BRAND NAME : BAOFENG, Pofung MODEL NAME : UV—82, UV—82L, GT—5 CLIENT PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY DATE OF ISSUE : Jun. 23, 2018 STANDARD(S) : FCC Part 15 Rules REPORT VERSION : V 11 Attestation of Global GOmplianke (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced e t the written permission of the test laboratory and shall not be quoted out 0 The results ,m i est is issued by/A , this docu/mo it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be : AGC > confirmed a tfittp://www.agc-% t.com. 9 Attestatiq ,ngIoba!Q o pliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@agc—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC02294180601FE08 Page 2 of 30 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 13, 2018 Invalid Initial Release V1.1 1st Jun. 23, 2018 Valid Update the comments.

Report No.: AGC02294180601FE08 Page 3 of 30 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE ................................................................................................................. 4 2. PRODUCT INFORMATION .............................................................................................................................. 5 3. IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION ............................................................... 6 4. SUPPORT EQUIPMENT LIST ......................................................................................................................... 7 5. SYSTEM DESCRIPTION .................................................................................................................................. 7 6. SUMMARY OF TEST RESULTS ..................................................................................................................... 8 7. FCC RADIATED EMISSION TEST .................................................................................................................. 9 7.1. TEST EQUIPMENT OF RADIATED EMISSION .................................................................................... 9 7.2. LIMITS OF RADIATED EMISSION TEST .............................................................................................. 9 7.3 BLOCK DIAGRAM OF RADIATED EMISSION TEST ............................................................................ 9 7.4 PROCEDURE OF RADIATED EMISSION TEST ................................................................................. 11 7.5 TEST RESULT OF RADIATED EMISSION TEST ................................................................................ 12 8. CONDUCTED EMISSION TEST .................................................................................................................... 16 8.1 PROVISIONS APPLICABLE ................................................................................................................. 16 8.2 MEASUREMENT PROCEDURE ........................................................................................................... 16 8.3 TEST SETUP BLOCK DIAGRAM ......................................................................................................... 17 8.4 TEST RESULT....................................................................................................................................... 18 9. ANTENNA CONDUCTED POWER FOR RECEIVERS ................................................................................. 20 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP ............................................................................................ 23 APPENDIX 2 PHOTOGRAPHS OF EUT ........................................................................................................... 24

Report No.: AGC02294180601FE08 Page 4 of 30 1. VERIFICATION OF COMPLIANCE Applicant PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Manufacturer PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Product Designation DUAL BAND F3E TRANSCEIVER Brand name BAOFENG, Pofung Test Model UV-82 Serial Model UV-82L, GT-5 All the same except the model name, brand name appearance and shape. Serial Model Difference UV-82, UV-82L (Brand name is BAOFENG), GT-5(Brand name is Pofung) Hardware Version UV82-FST8-VER02 Software Version UV82 Measurement Procedure ANSI C63.4: 2014 Date of test: Jun. 05, 2018 to Jun. 13, 2018 Deviation: None Condition of Test Sample Normal The above equipment was tested by Attestation Of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set forth in the FCC Rules and Regulations Part 15, the measurement procedure according to ANSI C63.4:2014. This said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment are within the compliance requirements. The test results of this report relate only to the tested sample identified in this report. Tested by Steven Zhou(Zhou Pengyun) Jun. 13, 2018 Reviewed by Bart Xie(Xie Xiaobin) Jun. 23, 2018

Report No.: AGC02294180601FE08 Page 5 of 30 2. PRODUCT INFORMATION The EUT is a DUAL BAND FM TRANSCEIVER designed for voice communication. It is designed by way of utilizing the F3E modulation achieves the system operating. A major technical description of EUT is described as following: Communication Type Voice / Tone only Modulation FM RX Frequency Range Rx:136 MHz -174 MHz, 400MHz -480MHz Emission Type F3E Antenna Designation Detachable Antenna Gain 2.15dBi Power Supply DC 7.4V 2000mAh, charging with DC 8.4V. INPUT:AC 110-240V~ 50/60Hz ,0.4A Adapter Parameter OUTPUT:DC 10V 1A INPUT: DC 10V 1A Charger Parameter OUTPUT:DC 8.4V 0.5A I/O Port Information ( Applicable Not Applicable) I/O Port of EUT I/O Port Type Q’TY Cable Tested with DC Input Port 1 1.14m, Unshielded 1 Antenna Connect Port 1 0 1

Report No.: AGC02294180601FE08 Page 6 of 30 3. IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION Test Site Attestation of Global Compliance (Shenzhen) Co., Ltd 1-2F., Bldg.2, No.1-4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang, Location Bao’an District B112-B113, Bldg.12, Baoan Bldg Materials Center, No.1 of Xixiang Inner Ring Road, Baoan District, Shenzhen 518012 NVLAP LAB CODE 600153-0 Designation Number CN5028 FCC Test Firm 682566 Registration Number Attestation of Global Compliance(Shenzhen) Co., Ltd is accredited by National Description Voluntary Laboratory Accreditation program, NVLAP Code 600153-0 List Of Test Equipment: TEST EQUIPMENT OF CONDUCTED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESCI 100096 Jul. 02, 2017 Jul. 01, 2018 AMN/LISN R&S ESH2-Z5 100086 Aug. 24, 2017 Aug. 23, 2018 AGC-CON03 TEST SOFTWARE FR EZ-EMC -- -- A TEST EQUIPMENT OF RADIATED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESPI 101206 Jul. 02, 2017 Jul. 01, 2018 ANTENNA SCHWARZBECK VULB9168 494 Sep. 27, 2017 Sep. 28, 2019 TEST RECEIVER R&S ESCI 100694 June 29, 2017 June 28,2018 ANTENNA SCHWARZBECK VULB9168 D69250 Sep. 27, 2017 Sep. 28, 2019 POSITIONING MF MF-7802 MF780208285 -- -- CONTROLLER HORN ANTENNA ETS LINDGREN 3117 00034609 May. 17, 2017 May. 18, 2019

Report No.: AGC02294180601FE08 Page 7 of 30 4. SUPPORT EQUIPMENT LIST Device Type Manufacturer Model Name Serial No. Data Cable Power Cable -- -- -- -- -- -- 5. SYSTEM DESCRIPTION EUT test procedure: 1. Connect EUT and peripheral devices. 2. Power on the EUT, the EUT begins to work. 3. Make sure the EUT normal working. EMC TEST MODES No. TEST MODES 1 Scanning mode 2 Scanning stopped/Receiving Note: Only the result of the worst case was recorded in the report.

Report No.: AGC02294180601FE08 Page 8 of 30 6. SUMMARY OF TEST RESULTS FCC Rules Description Of Test Result §15.107 Conduction Emission Compliant §15.109 Radiated Emission Compliant §15.111 Antenna Conducted Power for receivers Compliant

Report No.: AGC02294180601FE08 Page 9 of 30 7. FCC RADIATED EMISSION TEST 7.1. TEST EQUIPMENT OF RADIATED EMISSION 7.2. LIMITS OF RADIATED EMISSION TEST Frequency Distance Maximum Field Strength Limit (MHz) (m) (dBuV/m/ Q.P.) 30~88 3 41.0 88~216 3 45.0 216~960 3 48.0 960~2000 3 53.5 **Note: The lower limit shall apply at the transition frequency. Because the EUT RX frequency range up to 480 MHz, so the upper the frequency range up to 2 GHz. 7.3 BLOCK DIAGRAM OF RADIATED EMISSION TEST RADIATED EMISSION TEST SETUP 30MHz-1000MHz

Report No.: AGC02294180601FE08 Page 10 of 30 RADIATED EMISSION TEST SETUP ABOVE 1000MHz

Report No.: AGC02294180601FE08 Page 11 of 30 7.4 PROCEDURE OF RADIATED EMISSION TEST 1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden turntable with a height of 0.8 meters is used which is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2) Support equipment, if needed, was placed as per ANSI C63.4. 3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. 4) The EUT received power by AC 120V/60Hz. 5) The antenna was placed at 3 meter away from the EUT as stated in FCC Part 15. The antenna connected to the Analyzer via a cable and at times a pre-amplifier would be used. 6) The Analyzer / Receiver quickly scanned from 30MHz to 1000MHz. The EUT test program was started. Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level. 7) The test mode(s) were scanned during the test: 8) Recorded at least the six highest emissions. Emission frequency, amplitude, antenna position, polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit and Q.P./Peak reading is presented. For emissions below 1GHz, use 120KHz RBW and VBW>=3RBW for QP reading. 9) For emissions above 1GHz, use 1MHz RBW and 3MHz VBW for peak reading. Then 1MHz RBW and 10Hz VBW for average reading in spectrum analyzer. 10) When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum values. 11)If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz. 12) For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that means the emissions level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. 13) In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High - Low scan is not required in this case. 14) The test data of the worst case condition (mode 1) was reported on the following Data page

Report No.: AGC02294180601FE08 Page 12 of 30 7.5 TEST RESULT OF RADIATED EMISSION TEST UV-82 (mode 1) Radiated Emission Test –Horizontal -3m Below 1G Factor Level Limit Frequency Reading Margin Height Angle Polarization dB dB(uV/m) dB(uV/m) Pass/Fail MHz dB(uV) dB cm deg (1/m) PK QP 80.925 H 10.4 12.3 22.7 40.0 17.3 Pass 200.0 303.2 102.750 H 11.4 13.8 25.2 43.5 18.3 Pass 150.0 10.2 129.425 H 12.3 16.2 28.5 43.5 15.0 Pass 200.0 288.5 515.970 H 6.5 23.2 29.7 46.0 16.3 Pass 150.0 231.2 825.400 H 7.2 29.2 36.4 46.0 9.6 Pass 200.0 37.4 988.845 H 7.1 31.0 38.1 54.0 15.9 Pass 100.0 285.8 RESULT: PASS

Report No.: AGC02294180601FE08 Page 13 of 30 Radiated Emission Test –Vertical -3m Below 1G Factor Level Limit Frequency Reading Margin Height Angle Polarization dB dB(uV/m) dB(uV/m) Pass/Fail MHz dB(uV) dB cm deg (1/m) PK QP 77.530 V 14.8 12.5 27.3 40.0 12.7 Pass 100.0 37.4 128.455 V 13.3 16.1 29.4 43.5 14.1 Pass 100.0 247.1 236.125 V 7.1 16.1 23.2 46.0 22.8 Pass 100.0 359.0 595.510 V 7.9 24.9 32.8 46.0 13.2 Pass 100.0 34.4 636.735 V 7.3 25.5 32.8 46.0 13.2 Pass 150.0 166.2 998.545 V 6.4 31.1 37.5 54.0 16.5 Pass 150.0 305.6 RESULT: PASS Note: 1. Factor=Antenna Factor + Cable loss - Amplifier gain, Margin=Measurement-Limit. 2. The “Factor” value can be calculated automatically by software of measurement system. 3. Emissions range from 1GHz to 2GHz have 20dB margin. No recording in the test report. 4. Only the data of the worst case would be record in this test report.

Report No.: AGC02294180601FE08 Page 14 of 30 GT-5 (mode 1) Radiated Emission Test –Horizontal -3m Below 1G Factor Level Limit Frequency Reading Margin Height Angle Polarization dB dB(uV/m) dB(uV/m) Pass/Fail MHz dB(uV) dB cm deg (1/m) PK QP 79.470 H 12.4 12.3 24.7 40.0 15.3 Pass 200.0 309.3 127.000 H 12.9 16.0 28.9 43.5 14.6 Pass 150.0 258.5 158.040 H 7.7 16.6 24.3 43.5 19.2 Pass 200.0 263.3 233.700 H 7.0 16.0 23.0 46.0 23.0 Pass 100.0 243.3 598.905 H 7.1 24.9 32.0 46.0 14.0 Pass 100.0 128.9 979.630 H 6.4 30.9 37.3 54.0 16.7 Pass 200.0 312.5 RESULT: PASS

Report No.: AGC02294180601FE08 Page 15 of 30 Radiated Emission Test –Vertical -3m Below 1G Factor Level Limit Frequency Reading Margin Height Angle Polarization dB dB(uV/m) dB(uV/m) Pass/Fail MHz dB(uV) dB cm deg (1/m) PK QP 74.135 V 12.4 13.2 25.6 40.0 14.4 Pass 100.0 120.7 128.455 V 12.0 16.1 28.1 43.5 15.4 Pass 100.0 231.7 350.585 V 6.2 18.9 25.1 46.0 20.9 Pass 150.0 182.5 518.880 V 6.1 23.2 29.3 46.0 16.7 Pass 150.0 229.9 672.625 V 7.0 25.9 32.9 46.0 13.1 Pass 100.0 308.1 999.030 V 6.0 31.1 37.1 54.0 16.9 Pass 100.0 68.1 RESULT: PASS Note: 1. Factor=Antenna Factor + Cable loss - Amplifier gain, Margin=Measurement-Limit. 2. The “Factor” value can be calculated automatically by software of measurement system. 3. Emissions range from 1GHz to 2GHz have 20dB margin. No recording in the test report. 4. Only the data of the worst case would be record in this test report.

Report No.: AGC02294180601FE08 Page 16 of 30 8. CONDUCTED EMISSION TEST 8.1 PROVISIONS APPLICABLE For an intentional radiator that is designed to be connected to the public utility (AC) power line, the, the radio frequency voltage that is conducted back onto the AC power line on any frequencies within the band 150 KHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50uH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequencies ranges. Conducted Limit(dBuV) Frequency of Emission (MHz) Quasi-Peak Average 0.15 – 0.5 66 to 56 * 56 to 46 * 0.5 – 5 56 46 5 – 30 60 50 * Decreases with the logarithm of the frequency. 8.2 MEASUREMENT PROCEDURE (1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. (2) Support equipment, if needed, was placed as per ANSI C63.4. (3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. (4) The EUT received AC 120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. (5) All support equipments received AC power from a second LISN, if any. (6) The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. (7) Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. During the above scans, the emissions were maximized by cable manipulation.

Report No.: AGC02294180601FE08 Page 17 of 30 8.3 TEST SETUP BLOCK DIAGRAM

AG °s 7 I # m Attestation of Global Compliance Report No.: AGCO02294180601FEO8 Page 18 of 30 8.4 TEST RESULT CONDUCTED EMISSION TEST — LINE L I I — 1 1 1 1 150k 300k 400k 600k 800k 1M 2M 3M 4M 5M 6M 8M 10M 20M 30M Frequency [Hz] MEASUREMENT RESULT: Frequency Level Transd Limit Margin Detector Line PE Miz aBuy dB dBuvy dB 0.178000 43 .40 10 .0 €5 21.2 QP L1 FLO 0.23223000 39 .80 10 .1 63 22.9 QP L1 FLO 0.374000 36 .50 10 .1 €1 34.5 P L1 FLO 0. 326000 8 .50 10 .1 60 21.1 QP L1 FLO 0.450000 41 .30 10 .1 57 151.6 QP L1 FLO 0. 6423000 34.40 10 .1 56 21.6 QP L1 FLO MEASUREMENT RESULT: Frequency Level Transd Limit Margin Detector Line PE MHz aBuvy dB adBuVv dB 0.178000 28 .10 10 .0 55 a6.5 AV L1 FLO 0.23223000 32 .00 10 .1 53 30.7 AV L1 FLO 0.290000 31.70 10 .1 51 28.8 AV L1 FLO 0. 334000 25.40 10 .1 49 214.0 AV L1 FLO 0.4223000 25 .90 10 .1 47 21.5 AV L1 FLO 0, 510000 35 .20 10 .1 146 20.8 AV L1 FLO RESULT: PASS The results s 6tial O fi%@)} treport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued b , this doc@énc it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be ° AGC > confirmed tfittp://www.agc-«& t.com. Attestatiq ,2f Globa!Q o Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

® 2 l A\G fistatfi;ar fl;a, % (i%pliafi;! 35 Report No.: AGC02294180601FEO8 Page 19 of 30 CONDUCTED EMISSION TEST — LINE N MEASUREMENT RESULT: Frequency Level Transd Limit Margin Detector Line FE MHz aBuv dB aBuv cdB 0.182000 37 .70 10 .0 64 26.7 QP N FLO 0.326000 3€6 .90 10.1 63 25.7 QP N FLO 0.370000 34 .00 10.1 €1 27.1 QP N FLO 0. 338000 32.70 10.1 59 26.6 QP N FLO 0.454000 40.70 10.1 57 16.1 @QP N FLO 0. 586000 35 .90 10.1 5€ 20.1 QP N FLO MEASUREMENT RESULT: Frequency Level Transd Limit Margin Detector Line PE MHz adBuvy dB adBuv cdB 0.174000 36 .40 10 .0 55 28.4 RAV N FLO 0. 2318000 31.20 10.1 53 31.7 RV N FLO 0.346000 18.80 10.1 52 32.1 RAV N FLO 0.330000 33 .50 10.1 50 37.0 AV N FLO 0. 374000 21 .40 10.1 & 27.0 V N FLO 0.463000 25 .30 10 .1 47 21.4 AV N FLO RESULT: PASS The results s‘ O virl fii@;}" kreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued b , this doc@é it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be ° AGC > confirmed tfittp://www.agc-«& t.com. Attestatic /2f Globa!Q ompliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

© A\G 3 7 h t i al T :n Attestation of Global Compliance Report No.: AGC02294180601FEO8 Page 20 of 30 9. ANTENNA CONDUCTED POWER FOR RECEIVERS LIMIT The antenna conducted power of the receiver as defined in §15.111 shall not exceed the values given in the following tables Frequency Range 9 KHz to 2GHz Limit 2.0 nw (—57 dBm ) TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE 1. The receiver antenna terminal connected to a spectrum analyzer. 2. The test data of the worst case condition (mode 1) was reported on the following Data page. The results ’m,6tison| o thisfeaost report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu/m it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-% t.com. o Attestatic m ® ) i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 iN¥ Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC02294180601FE08 Page 21 of 30 TEST RESULTS Conducted Measurement (9 KHz to 150 KHz) Conducted Measurement (150 KHz to 30MHz)

Report No.: AGC02294180601FE08 Page 22 of 30 Conducted Measurement (30MHz to 1GHz) Conducted Measurement (1GHz to 2GHz) PASS

Report No.: AGC02294180601FE08 Page 23 of 30 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP CONDUCTED EMISSION TEST SETUP RADIATED EMISSION TEST SETUP

Report No.: AGC02294180601FE08 Page 24 of 30 APPENDIX 2 PHOTOGRAPHS OF EUT TOTAL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC02294180601FE08 Page 25 of 30 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC02294180601FE08 Page 26 of 30 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC02294180601FE08 Page 27 of 30 RIGHT VIEW OF EUT OPEN VIEW-1 OF EUT

Report No.: AGC02294180601FE08 Page 28 of 30 INTERNAL VIEW-1 OF EUT INTERNAL VIEW-2 OF EUT

Report No.: AGC02294180601FE08 Page 29 of 30 INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT

Report No.: AGC02294180601FE08 Page 30 of 30 INTERNAL VIEW-5 OF EUT ----END OF REPORT----


Document Created: 2018-06-25 10:50:04
Document Modified: 2018-06-25 10:50:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC