Modular Approval Letter

FCC ID: 2AJFZ-MBC005

Cover Letter(s)

Download: PDF
FCCID_3202993

telefication RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00—1407) FCC ID: 2AJFZ—MBCO05 Items to be covered Answerfrom applicant 1, The modular transmitter must have its own RF shielding. Yes. The modular transmitter has its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs Yes. The module has buffered are provided) to ensure that the module will comply with Part 15 requirements modulation/data inputs to under conditions of excessive data rates or over—modulation. ensure that the device will comply with Part 15 requirements with any type of input signal. 3. The modular transmitter must have its own power supply regulation. Yes. The module contains power supply regulation on the module. 4. The modular transmitter must comply with the antenna requirements of Section Yes. The module contains a 15.203 and 15.204(c). The antenna must either be permanently attached or employ unique antenna connector, per a "unique" antenna coupler (at all connections between the module and the Sections 15.203, 5.204(c) antenna, including the cable).. 5. The modular transmitter must be tested in a stand—alone configuration, i.e., the Yes. The demonstrates module must not be inside another device during testing. This is intended to compliance in a stand—alone demonstrate that the module is capable of complying with Part 15 emission limits configuration regardless of the device into which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if |_Yes. The module is labelled the FCC ID is not visible when the module is installed inside another device, then with its permanently affixed the outside of the device into which the module is installed must also display a FCC ID label. label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmittee Module FCC ID: XYZMODELI" or "Contains FCC ID: XYZMODELI." Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating Yes. The module complies requirements applicable to the transmitter and the manufacturer must provide with all specific rules adequate instructions along with the module to explain any such requirements. A applicable to the transmitter copy of these instructions must be included in the application for equipment including all the conditions authorization. For example, there are very strict operational and timing provided in the integration requirements that must be met before a transmitter is authorized for operation under instructions by the grantee. Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure Yes. The module complies requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific with RF exposure Sections of Part 15, including 15.3 19(i), 15.407(f), 15.253(f) and 15.255(g), requirements. require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be

telefication RF_734_00, Issue 1 Name and surname of applicant (or authorized representative): Yelena Kouznetsova Date: 08/15/2016 % Signature: %


Document Created: 2016-08-30 10:49:48
Document Modified: 2016-08-30 10:49:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC