Test report

FCC ID: 2AJDD-IDIAGT138

Test Report

Download: PDF
FCCID_3406292

Global United Technology Services Co., Ltd. Report No.: GTS201704000180F01 FCC REPORT Applicant: SHENZHEN FCAR TECHNOLOGY CO.,LTD Address of Applicant: 8th floor, Chuangyi Building, No. 3025 Nanhai Ave., Nanshan, Shenzhen, Guangdong, China Manufacturer: SHENZHEN FCAR TECHNOLOGY CO.,LTD Address of 8th floor, Chuangyi Building, No. 3025 Nanhai Ave., Nanshan, Manufacturer: Shenzhen, Guangdong, China Factory: SHENZHEN FCAR TECHNOLOGY CO.,LTD Address of Factory: West 1F, Bldg. B, Hengchao Industrial Park, Tangtou North Ave., Bao'an, Shenzhen, China Equipment Under Test (EUT) Product Name: TPMS Diagnostic Tool Model No.: FT-138 Trade Mark: FCAR FCC ID: 2AJDD-IDIAGT138 Applicable standards: FCC CFR Title 47 Part 15 Subpart C:2016 Date of sample receipt: April 27, 2017 Date of Test: May 02-08, 2017 Date of report issued: May 09, 2017 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Robinson Lo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver.

Report No.: GTS201704000180F01 2 Version Version No. Date Description 00 May 09, 2017 Original Prepared By: Date: May 09, 2017 Project Engineer Check By: Date: May 09, 2017 Reviewer Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 25

Report No.: GTS201704000180F01 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY ............................................................................................................ 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.2 TEST MODE ........................................................................................................................................ 6 5.3 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 6 5.4 TEST FACILITY.................................................................................................................................... 6 5.5 TEST LOCATION ................................................................................................................................. 6 5.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ......................................................................... 6 6 TEST INSTRUMENTS LIST ..................................................................................................................... 7 7 TEST RESULTS AND MEASUREMENT DATA...................................................................................... 8 7.1 ANTENNA REQUIREMENT:.................................................................................................................... 8 7.2 CONDUCTED EMISSIONS ..................................................................................................................... 9 7.3 RADIATED EMISSION METHOD ........................................................................................................... 12 7.4 20DB OCCUPY BANDWIDTH .............................................................................................................. 17 8 TEST SETUP PHOTO ............................................................................................................................ 18 9 EUT CONSTRUCTIONAL DETAILS ..................................................................................................... 20 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 25

Report No.: GTS201704000180F01 4 Test Summary Test Item Section in CFR 47 Result Antenna requirement 15.203 Pass AC Power Line Conducted Emission 15.207 Pass Radiated Emission 15.209 Pass 20dB Bandwidth 15.205 Pass Pass: The EUT complies with the essential requirements in the standard. Remark: Test according to ANSI C63.10 2013 and ANSI C63.4: 2014 4.1 Measurement Uncertainty Test Item Frequency Range Measurement Uncertainty Notes Radiated Emission 9kHz ~ 30MHz ± 4.34dB (1) Radiated Emission 30MHz ~ 1000MHz ± 4.24dB (1) Radiated Emission 1GHz ~ 26.5GHz ± 4.68dB (1) AC Power Line Conducted 0.15MHz ~ 30MHz ± 3.45dB (1) Emission Note (1): The measurement uncertainty is for coverage factor of k=2 and a level of confidence of 95%. Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 25

Report No.: GTS201704000180F01 5 General Information 5.1 General Description of EUT Product Name: TPMS Diagnostic Tool Model No.: FT-138 Operation Frequency: 125KHz Modulation type: ASK Antenna Type: Integral Antenna Antenna gain: 0dBi (declare by Manufacturer) Power supply: Adapter: Model:GME12A-050200FXR Input: AC 100-240V, 50/60Hz, 0.4A Output: DC 5V, 2A or DC 3.7V 3500mAh Lithium Battery Channel Frequency Test channel 125KHz Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 25

Report No.: GTS201704000180F01 5.2 Test mode Transmitting mode Keep the EUT in continuously transmitting and charging mode 5.3 Description of Support Units N/A 5.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: ● FCC —Registration No.: 600491 Global United Technology Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in files. Registration 600491, June 22, 2016. ● Industry Canada (IC) —Registration No.: 9079A-2 The 3m Semi-anechoic chamber of Global United Technology Services Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 9079A-2, August 15, 2016. 5.5 Test Location All tests were performed at: Global United Technology Services Co., Ltd. Address: No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Tel: 0755-27798480 Fax: 0755-27798960 5.6 Other Information Requested by the Customer None. Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 25

Report No.: GTS201704000180F01 6 Test Instruments list Radiated Emission: Inventory Cal.Date Cal.Due date Item Test Equipment Manufacturer Model No. No. (mm-dd-yy) (mm-dd-yy) 3m Semi- Anechoic 1 ZhongYu Electron 9.2(L)*6.2(W)* 6.4(H) GTS250 July 03 2015 July 02 2020 Chamber 2 Control Room ZhongYu Electron 6.2(L)*2.5(W)* 2.4(H) GTS251 N/A N/A 3 Spectrum Analyzer Agilent E4440A GTS533 June 29 2016 June 28 2017 4 EMI Test Receiver Rohde & Schwarz ESU26 GTS203 June 29 2016 June 28 2017 5 Loop Antenna Zhinan ZN30900A GTS534 June. 29 2016 June. 28 2017 SCHWARZBECK 6 BiConiLog Antenna VULB9163 GTS214 June 29 2016 June 28 2017 MESS-ELEKTRONIK Double -ridged waveguide SCHWARZBECK 7 9120D-829 GTS208 June 29 2016 June 28 2017 horn MESS-ELEKTRONIK 8 Horn Antenna ETS-LINDGREN 3160 GTS217 June 29 2016 June 28 2017 9 EMI Test Software AUDIX E3 N/A N/A N/A 10 Coaxial Cable GTS N/A GTS213 June 29 2016 June 28 2017 11 Coaxial Cable GTS N/A GTS211 June 29 2016 June 28 2017 12 Coaxial cable GTS N/A GTS210 June 29 2016 June 28 2017 13 Coaxial Cable GTS N/A GTS212 June 29 2016 June 28 2017 14 Amplifier(100kHz-3GHz) HP 8347A GTS204 June 29 2016 June 28 2017 15 Amplifier(2GHz-20GHz) HP 8349B GTS206 June 29 2016 June 28 2017 AFS33-18002 16 Amplifier (18-26GHz) Rohde & Schwarz GTS218 June 29 2016 June 28 2017 650-30-8P-44 17 Band filter Amindeon 82346 GTS219 June 29 2016 June 28 2017 18 Power Meter Anritsu ML2495A GTS540 June 29 2016 June 28 2017 19 Power Sensor Anritsu MA2411B GTS541 June 29 2016 June 28 2017 Conducted Emission: Cal.Date Cal.Due date Item Test Equipment Manufacturer Model No. Inventory No. (mm-dd-yy) (mm-dd-yy) 1 Shielding Room ZhongYu Electron 7.3(L)x3.1(W)x2.9(H) GTS252 May.16 2014 May.15 2019 2 EMI Test Receiver R&S ESCI 7 GTS552 June. 29 2016 June. 28 2017 3 Coaxial Switch ANRITSU CORP MP59B GTS225 June. 29 2016 June. 28 2017 SCHWARZBECK 4 Artificial Mains Network NSLK8127 GTS226 June. 29 2016 June. 28 2017 MESS 5 Coaxial Cable GTS N/A GTS227 N/A N/A 6 EMI Test Software AUDIX E3 N/A N/A N/A 7 Thermo meter KTJ TA328 GTS233 June. 29 2016 June. 28 2017 General used equipment: Inventory Cal.Date Cal.Due date Item Test Equipment Manufacturer Model No. No. (mm-dd-yy) (mm-dd-yy) 1 Barometer ChangChun DYM3 GTS257 June 29 2016 June 28 2017 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 25

Report No.: GTS201704000180F01 7 Test results and Measurement Data 7.1 Antenna requirement: Standard requirement: FCC Part15 C Section 15.203 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. E.U.T Antenna: The antenna is Integral Antenna, the best case gain of the antenna is 0dBi Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 25

Report No.: GTS201704000180F01 7.2 Conducted Emissions Test Requirement: FCC Part15 C Section 15.207 Test Method: ANSI C63.10:2013 Test Frequency Range: 150KHz to 30MHz Class / Severity: Class B Receiver setup: RBW=9KHz, VBW=30KHz, Sweep time=auto Limit: Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. Test setup: Test procedure: 1. The E.U.T and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm/50uH coupling impedance for the measuring equipment. 2. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refer to the block diagram of the test setup and photographs). 3. Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10:2013 on conducted measurement. Test Instruments: Refer to section 6.0 for details Test mode: Refer to section 5.2 for details Test results: Pass Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 25

Report No.: GTS201704000180F01 Measurement data Line: Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 25

Report No.: GTS201704000180F01 Neutral: Notes: 1. An initial pre-scan was performed on the line and neutral lines with peak detector. 2. Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. Final Level =Receiver Read level + LISN Factor + Cable Loss 4. If the average limit is met when using a quasi-peak detector receiver, the EUT shall be deemed to meet both limits and measurement with the average detector receiver is unnecessary. Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 11 of 25

Report No.: GTS201704000180F01 7.3 Radiated Emission Method Test Requirement: FCC Part15 C Section 15.209 Test Method: ANSI C63.4:2014 Test Frequency Range: 9kHz to 1GHz Test site: Measurement Distance: 3m Receiver setup: Frequency Detector RBW VBW Remark 9kHz - 30MHz Quasi-peak 10kHz 30kHz Quasi-peak Value 30MHz-1GHz Quasi-peak 120kHz 300kHz Quasi-peak Value Remark: For the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission test in these three bands are based on measurements employing an average detector. Limit: Limits for frequency below 30MHz (Spurious Emissions) Measurement Frequency Limit (uV/m) Remark Distance(m) 0.009-0.490 2400/F(kHz) 300 Quasi-peak Value 0.490-1.705 24000/F(kHz) 30 Quasi-peak Value 1.705-30 30 30 Quasi-peak Value Limits for frequency Above 30MHz Frequency Limit (dBuV/m @3m) Remark 30MHz-88MHz 40.00 Quasi-peak Value 88MHz-216MHz 43.50 Quasi-peak Value 216MHz-960MHz 46.00 Quasi-peak Value 960MHz-1GHz 54.00 Quasi-peak Value 54.00 Average Value Above 1GHz 74.00 Peak Value Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. Test Procedure: 1. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter camber. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 12 of 25

Report No.: GTS201704000180F01 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. 7. The radiation measurements are performed in X, Y, Z axis positioning. And found the Y axis positioning which it is worse case, only the test worst case mode is recorded in the report. Test setup: Below 30MHz 30MHz ~ 1000MHz Test Instruments: Refer to section 6.0 for details Test mode: Refer to section 5.2 for details Test results: Pass Measurement data: Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 13 of 25

Report No.: GTS201704000180F01 Measurement data: Note: Limit dBuV/m @3m = Limit dBuV/m @300m+ 80 Limit dBuV/m @3m = Limit dBuV/m @30m + 40 9kHz ~ 30MHz Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 14 of 25

Report No.: GTS201704000180F01 30MHz~1GHz Vertical: Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 15 of 25

Report No.: GTS201704000180F01 Horizontal: Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 16 of 25

Report No.: GTS201704000180F01 7.4 20dB Occupy Bandwidth Test Requirement: FCC Part15 C Section 15.215 Test Method: ANSI C63.10: 2013 Test setup: Test Instruments: Refer to section 6.0 for details Test mode: Refer to section 5.2 for details Test results: Pass Measurement Data Test frequency 20dB bandwidth(KHz) Result 125KHz 10.974 Pass Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 17 of 25

Report No.: GTS201704000180F01 8 Test Setup Photo Radiated Emission Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 18 of 25

Report No.: GTS201704000180F01 Conducted Emission Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 19 of 25

Report No.: GTS201704000180F01 9 EUT Constructional Details Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 20 of 25

Report No.: GTS201704000180F01 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 21 of 25

Report No.: GTS201704000180F01 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 22 of 25

Report No.: GTS201704000180F01 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 23 of 25

Report No.: GTS201704000180F01 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 24 of 25

Report No.: GTS201704000180F01 ------End------ Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 25 of 25


Document Created: 2017-05-22 15:23:56
Document Modified: 2017-05-22 15:23:56
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC