TRE18030181-2_FCC_SAR_RF Exposure

FCC ID: 2AJDD-IDIAGSF7SX

RF Exposure Info

Download: PDF
FCCID_3827024

8 In Collaboration with TTL s p _e a q CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://wwrw.chinattl.cn Impedance Measurement Plot for Head TSL Tri S11 Log Mag 10.00d8/ Ref 0.000ds [Fi] 50. 00 >1 2.4500000 GHz ~23.763 db 40. 00 30. 00 20. 00 10.00 0.000p —10.00 ~20.00 ~30. 00 ~40.00 ~50.00 PB 511 smith (R+]X) scale 1.000U [F1 vel] >1.2.4500000 ghz 55.083 n 4.5461 n 205.3 [1 Strt 225 ce IFBW 100 He Stop 2.65 ht IRI Certificate No: Z17—97210 Page 6 of 8

£ In Collaboration with TTL a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp://www.chinattl.en DASY5 Validation Report for Body TSL Date: 10.26.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 884 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: f= 2450 MHz; 0 = 1.923 $/m; & = 52.34; p = 1000 kg/m* Phantom section: Right Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN7307; ConvF(7.55,7.55,7.55); Calibrated: 3/17/2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE3 $n536; Calibrated: 10/9/2017 & Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=Smm Reference Value= 101.3 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 25.1 W/kg SAR(I g) = 12.6 W/kg; SAR(10 g) = 5.88 W/kg Maximum value of SAR (measured) =20.6 W/kg dB 0 ~4.29 —8.58 12.86 17.16 L. 21.44 0 dB =20.6 W/kg = 13.14 dBW/kg Certificate No: Z17—97210 Page 7 of 8

® In Collaboration with TTL $ e a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://worw.chinattl.en Impedance Measurement Plot for Body TSL Tri si1 Log Mag 10.00d/ Ref 0.000d8 [Fi] 50.00 >1 2.4500000 Giz —24.164 db 40.00 30. 00 20.00 10. 00 0. 000 (€ ~10.00 i —20.00 \?\_/%‘/f’// ~30.00 ~40. 00 50. 00 k PM s11 smith (R+jX) scale 1.000U [F1 bel] »1 24500000 aHz 50.098 n 6.2001 n 403.3 1 1 Stit aes 6t IFBW 100 He Stop 2165 6z IMaAIT Certificate No: Z17—97210 Page 8 of 8

Appendix A: Calibration Certificate 1.3. D5GHzV2 Dipole Calibration Certificate 23 of 38

Calibration Laboratory of . Schweizerischer Kalibrierdienst Schmid & Partner _ Service suisse détalonnage Engineering AG Servizio svizzero d taratura Zeughausstrasse 43, 8004 Zurich, Switzerland * mag S swiss Calibration Service Hilgzs Accredited by the Swiss Accreditation Srvice (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEC 62209—2, "Evaluation of Human Exposure to Radio Frequency Fields from Handheld and Body—Mounted Wireless Communication Devices in the Frequency Range of 30 MHz to 6 GHz: Human models, Instrumentation, and Procedures"; Part 2: "Procedure to determine the Specific Absorption Rate (SAR) for including accessories and multiple transmitters", March 2010 b) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" c) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1019_Aug17 Page 2 of 16

Measurement Conditions DASY system configuration, as far as not iven on page 1. DASY Version DASY5 V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy =4.0 mm, da =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz «1 MHz 5900 MHz x 1 MHz Frequency 5500 MHz x 1 MHz 5600 MHz + 1 MHz 5800 MHz + 1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 0.2) °C 84.7 26 % 4.48 mhoim x 6 % Head TSL temperature change during test <0.5°C SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.04 Wkg SAR for nominal Head TSL parameters normalized to 1W 79.7 Wikg # 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.30 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.7 Wikg # 19.5 % (k=2) Certificate No: D5GHzV2—1019_Aug17 Page 3 of 16

Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 34.5 26 % 4.57 mhoim + 6 % Head TSL temperature change during test <0.5°C ——— SAR result with Head TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.42 Wikg SAR for nominal Head TSL parameters normalized to 1W 83.4 W / kg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 241 Wig SAR for nominal Head TSL parameters normalized to 1W 23.8 Wikg £ 19.5 % (k=2) Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 0.2) °C 34.3 26 % 4.76 mho/m x 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.54 Wikg SAR for nominal Head TSL parameters normalized to 1W 84.6 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.45 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.2 Wikg x 19.5 % (k=2) Certificate No: DSGHzV2—1019_Aug17 Page 4 of 16

Head TSL parameters at 5600 MHz The followingparameters and calculations wereapplied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 £0.2) °C 34.1 26% 4.86 mho/m x 6 % Head TSL temperature change during test <0.5°C —— SAR result with Head TSL at 5600 MHz SAR averaged over 1 om? (1 g) of Head TSL Condition SAR measured 100 mW input power 8.47 Wikg SAR for nominal Head TSL parameters normalized to 1W 83.8 W/kg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.41 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.8 Wikg 2 19.5 % (k=2) Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35. 5.27 mho/m Measured Head TSL parameters (22.0 £0.2) °C 33.9 26 % 5.06 mho/m + 6 % Head TSL temperature change during test <0.5 °C ares SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.10 Wikg SAR for nominal Head TSL parameters normalized to 1W 80.2 W/kg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.30 Wkg SAR for nominal Head TSL parameters normalized to 1W 22.7 Wikg £ 19.5 %(k=2) Certificate No: DSGHzV2—1019_Aug17 Page5 of 16

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 £0.2) °C 47.0 26 % 5.32 mho/m x 6 % Body TSL temperature change during test <0.5°C SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.53 Wikg SAR for nominal Body TSL parameters normalized to 1W 74.7 Wikg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.11 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.9 W/kg 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.8 26 % 5.45 mhoim £ 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5300 MHz SAR averaged over 1 em‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.78 Wig SAR for nominal Body TSL parameters normalized to 1W 77.1 Wikg £19.9 % (ke2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.16 Wig SAR for nominal Body TSL parameters normalized to 1W 21.4 Wikg # 19.5 % (k=2) Certificate No: DSGHzV2—1019_Aug17 Page 6 of 16

Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.5 26 % 5.71 mho/m * 6 % Body TSL temperature change during test <05 °C —— — SAR result with Body TSL at 5500 MHz SAR averaged over 1 em‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.92 Whq SAR for nominal Body TSL parameters normalized to 1W 78.5 Wikg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.21 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.9 W/kg £ 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.3 26 % 5.84 mho/m + 6 % Body TSL temperature change during test <0.5°C ~~ «> SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 8.15 Wikg SAR for nominal Body TSL parameters normalized to 1W 80.8 Wikg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.26 Wig SAR for nominal Body TSL parameters normalized to 1W 22.3 Wikg # 19.5 % (k=2) Certificate No: D5GHzV2—1019_Aug17 Page 7 of 16

Body TSL parameters at 5800 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.0 26 % 6.12 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~—— ——— SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.45 Wig SAR for nominal Body TSL parameters normalized to 1W 73.9 Wikg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW inout power 2.08 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.6 W/kg 2 19.5 % (k=2) Certificate No: D5GHzV2—1019_Aug17 Page 8 of 16

Appendix (Additional assessments outside the scope of SCS108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 51.30—8.5 jQ Retum Loss ~21.5 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 58.2 0 —1.4 jQ Retun Loss —29.4 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 50.8 Q — 1.6 jQ Retun Loss —$5.0 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 56.3 0 —2.9 j0 Retum Loss —23.7 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 55.7 0 + 1.9 j0 Return Loss —24.8 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 52.20—6.6jQ Return Loss —23.4 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 59.2 0 — 0.8 jQ Return Loss —29.9 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 51.1 0 —0.6jQ Retum Loss —37.8 dB Certificate No: D5GHzV2—1019_Aug17 Page 9 of 16

Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 57.5 0 — 0.7 iA Return Loss —23.1 dB Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 56.9 0 + 4.4 jQ Retum Loss —22.4 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.205 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured The dipole is madeof standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is stil according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be dammaged. Additional EUT Data Manufactured by SPEAG Manufactured on February 05, 2004 Cartificate No: D5GHzV2—1019_Aug17 Page 10 of 16

DASY5 Validation Report for Head TSL Date: 20.08.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: DSGHzV2; Serial: DSGHzV2 — SN: 1019 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f= 5200 MHz; 0 = 4.48 S/m; & = 34.7; p= 1000 kg/m3 , Medium parameters used: £= 5300 MHz; 0 = 4.57 $/m; &, = 34.5; p = 1000 kg/m‘ , Medium parameters used: £= 5500 MHz; 0 = 4.76 S/m:; £, = 34.3; p = 1000 kg/m3 , Medium parameters used: £= 5600 MHz; 0 = 4.86 S/m; & = 34.1; p = 1000 kg/m‘ , Medium parameters used: £= 5800 MHz; 0 = 5.06 S/m; &, = 33.9; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: + Probe: EX3DV4 — SN3503; ConvF(5.52, 5.52, 5.52); Calibrated: 30.12.2016, ConvF(5.2, 5.2, 5.2); Calibrated: 30.12.2016, ConvF(5.01, 5.01, 5.01); Calibrated: 30.12.2016, ConvF(4.86, 4.86, 4.86); Calibrated: 30.12.2016, ConvF(4.91, 4.91, 4.91); Calibrated: 30.12.2016; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 $Sn601; Calibrated: 18.08.2017 «+ Phantom: Flat Phantom 5.0 (front); Type: QDOOOPSOAA; Serial: 1001 + DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.25 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 28.8 W/kg SAR(I g) = 8.04 W/kg:; SAR(10 g) = 2.3 W/kg Maximum value of SAR (measured) = 18.4 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value =66.75 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 31.4 W/kg SAR(I g) = 8.42 W/kg; SAR(10 g) =2.41 W/kg Maximum value of SAR (measured) = 19.3 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.08 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 32.8 W/kg SAR(I g) = 8.54 W/kg; SAR(10 g) = 2.45 W/kg Maximum value of SAR (measured) =20.0 W/kg Certificate No: D5GHzV2—1019_Aug17 Page 11 of 16

Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1 4mm Reference Value = 66.30 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 33.1 W/kg SAR(I g) = 8.47 W/kg; SAR(10 g) =2.41 W/kg Maximum value of SAR (measured) =20.1 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1 Amm Reference Value = 63.27 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 32.9 W/kg SAR(I g) =8.1 W/kg; SAR(10 g) = 2.3 W/kg Maximum value of SAR (measured) = 19.4 W/kg —6.00 12.00 18.00 —24.00 —30.00 0 dB = 19.4 W/kg = 12.88 dBW/kg Certificate No: D5GHzV2—1019_Aug17 Page 12 of 16

Impedance Measurement Plot for Head TSL CcBE san i uors i1 51.318 a se20 a 3.6000 pF 5 200.000 000 WHz 4 —_ x _ Hem 3 j CHL Markers bes \ 2 53.189 a ~1,4004 a con 5.30000 GHz ar 50,840 a ~1.9997 a 5.50000 iz 56.300 a €835 a fys 5.60000 GiHz s PssE $ s.e0000 giz Hid cn2 CH2 Markers a—29.435 4B cor 5.30000 Cz a—s4.956 dB s.sag0e 6iz 4—25.720 aB S.cada6 chiz ies 5:—24.048 aB 5.e0000 GHz Hig ART 5 006.000 000 MHz StoP 6 000.000 00@ MHz Certificate No: D5GHzV2—1019_Aug17 Page 18 of 16

DASY5 Validation Report for Body TSL Date: 20.08.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1019 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f= 5200 MHz; 0 = 5.32 S/m; &, = 47; p= 1000 kg/m3 , Medium parametersused: f = 5300 MHz; 0 = 5.45 S/m; &, = 46.8; p= 1000 kg/m‘ , Medium parameters used: £= 5500 MHz; 0 = 5.71 S/m; &, = 46.5; p = 1000 kg/m3 , Medium parameters used: £= 5600 MHz; 0 = 5.84 S/m; &, = 46.3; p= 1000 kg/m3 , Medium parameters used: {= 5800 MHz; 0 = 6.12 S/m; s, = 46; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: + Probe: EX3DV4 — SN3503; ConvF(5.01, 5.01, 5.01); Calibrated: 30.12.2016, ConvF(4.76, 4.76, 4.16); Calibrated: 30.12.2016, ConvF(4.52, 4.52, 4.52); Calibrated: 30.12.2016, ConvF(4.3, 4.3, 4.3); Calibrated: 30.12.2016, ConvF(4.47, 4.47, 4.47); Calibrated: 30.12.2016; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) «+ Electronics: DAE4 Sn601; Calibrated: 18.08.2017 + Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 + DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.85 V/m; Power Drift=0.03 dB Peak SAR (extrapolated) = 28.7 W/kg SAR(I g) =7.53 W/kg; SAR(10 g) = 2.11 W/kg Maximum value of SAR (measured) = 17.5 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Sean, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 60.61 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 30.9 W/kg SAR(L g) =7.78 W/kg; SAR(10 g) =2.16 W/kg Maximum value of SAR (measured) = 18.7 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, f=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 60.11 V/m; Power Drift =—0.03 dB Peak SAR (extrapolated) = 32.8 W/kg SAR(I g) =7.92 W/kg:; SAR(10 g) =2.21 Wkeg Maximum value of SAR (measured) = 19.1 W/kg Crtificate No: DSGHzV2—1019_Aug17 Page 14 of 16

aren ns en e nees nemn ns e e mcn en Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1 4mm Reference Value = 59.88 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 34.7 W/kg SAR(I g) = 8.15 W/kg; SAR(10 g) = 2.26 W/kzg Maximum value of SAR (measured) = 19.8 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, f=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 56.48 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 33.2 W/kg SAR(I g) =7.45 W/kg; SAR(10 g) = 2.08 W/kg Maximum value of SAR (measured) = 18.6 W/kg —6.00 ~12.00 —18.00 —24.00 —30.00 0 dB = 18.6 W/kg = 12.70 dBWez Certificate No: D5GHzV2—1019_Aug17 Page 15 of 16

Appendix A: Calibration Certificate ---------End-------- 38 of 38


Document Created: 2018-04-16 10:53:32
Document Modified: 2018-04-16 10:53:32
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC