Test Report

FCC ID: 2AJ9T-LH6000

Test Report

Download: PDF
FCCID_4141735

Access to the World FCC 47 CFR PART 15 SUBPART C CERTIFICATION TEST REPORT For Hotel Lock MODEL No.: LH6000 FCC ID: 2AJ9T-LH6000 Trademark: N/A REPORT NO.: ES190103028W ISSUE DATE: January 15, 2019 Prepared for ZKTECO CO., LTD. No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China 523728 Prepared by EMTEK(SHENZHEN) CO., LTD. Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 TRF No.:FCC 15.225/A Page 1 of 28 Report No.: ES190103028W Ver.1.0

Access to the World Table of Contents 1 EUT TECHNICAL DESCRIPTION ........................................................................................................... 4 2 SUMMARY OF TEST RESULT ................................................................................................................ 5 3 TEST METHODOLOGY ........................................................................................................................... 6 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................................................ 6 3.2 MEASUREMENT EQUIPMENT USED .......................................................................................... 6 3.3 DESCRIPTION OF TEST MODES................................................................................................. 7 4 FACILITIES AND ACCREDITATIONS ..................................................................................................... 8 4.1 FACILITIES .................................................................................................................................... 8 4.2 LABORATORY ACCREDITATIONS AND LISTINGS ..................................................................... 8 5 TEST SYSTEM UNCERTAINTY .............................................................................................................. 9 6 SETUP OF EQUIPMENT UNDER TEST ............................................................................................... 10 6.1 RADIO FREQUENCY TEST SETUP 1 ......................................................................................... 10 6.2 RADIO FREQUENCY TEST SETUP 2 ......................................................................................... 10 6.3 CONDUCTED EMISSION TEST SETUP ..................................................................................... 11 6.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ......................................................... 12 6.5 SUPPORT EQUIPMENT ............................................................................................................. 12 7 TEST REQUIREMENTS......................................................................................................................... 13 7.1 20DB BANDWIDTH ..................................................................................................................... 13 7.2 FREQUENCY STABILITY ............................................................................................................ 15 7.3 RADIATED SPURIOUS EMISSION ............................................................................................. 17 8 ANTENNA APPLICATION ..................................................................................................................... 28 TRF No.:FCC 15.225/A Page 2 of 28 Report No.: ES190103028W Ver.1.0

Access to the World TEST RESULT CERTIFICATION Applicant: ZKTECO CO., LTD. No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China 523728 Manufacturer: ZKTECO CO.,LTD. No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China 523728 Product Description: Hotel Lock Model Number: LH6000 Trademark: N/A Measurement Procedure Used: APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 2, Subpart J PASS FCC 47 CFR Part 15, Subpart C The above equipment was tested by EMTEK(SHENZHEN) CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.225 The test results of this report relate only to the tested sample identified in this report January 07, 2019 to January 14, 2019 Date of Test : Prepared by : Abel Wu/Editor Reviewer : Joe Xia/Supervisor Approved & Authorized Signer : Lisa Wang/Manager TRF No.:FCC 15.225/A Page 3 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 1 EUT TECHNICAL DESCRIPTION Characteristics Description EUT Description: Hotel Lock Model Number: LH6000 Modulation: RFID: ASK Operating Frequency 13.56MHz Range(s): Number of Channels: 1 channel Antenna Type /Gain: Induction coil Antenna DC supply: DC 6V from 4*AA battery Power supply: Adapter supply: Note: for more details, please refer to the User’s manual of the EUT. TRF No.:FCC 15.225/A Page 4 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 2 SUMMARY OF TEST RESULT FCC Part Clause Test Parameter Verdict Remark 2.1049 20dB Bandwidth PASS 15.225(e) Frequency stability PASS 15.225(d) Radiated Spurious Emissions PASS 15.209 15.207 Conducted Emission N/A 15.203 Antenna Requirement PASS NOTE1: N/A (Not Applicable) RELATED SUBMITTAL(S) / GRANT(S): This submittal(s) (test report) is intended for FCC ID: 2AJ9T-LH6000 filing to comply with Section 15.225 of the FCC Part 15, Subpart C Rules. TRF No.:FCC 15.225/A Page 5 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 3 TEST METHODOLOGY 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS According to its specifications, the EUT must comply with the requirements of the following standards: FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart C 3.2 MEASUREMENT EQUIPMENT USED 3.2.1 Conducted Emission Test Equipment EQUIPMENT MODEL SERIAL MFR LASTCAL. DUE CAL. TYPE NUMBER NUMBER Test Receiver Rohde & Schwarz ESCI 26115-010-0027 May 19, 2018 May 18, 2019 L.I.S.N. Rohde & Schwarz ENV216 101161 May 19, 2018 May 18, 2019 50Ω Coaxial Switch Anritsu MP59B 6100175589 May 20, 2018 May 19, 2019 Voltage Probe Rohde & Schwarz ESH2-Z3 100122 May 20, 2018 May 19, 2019 Pulse Limiter Rohde & Schwarz ESH3-Z2 100006 May 19, 2018 May 18, 2019 I.S.N Teseq GmbH ISN T800 30327 May 20, 2018 May 19, 2019 3.2.2 Radiated Emission Test Equipment EQUIPMENT MFR MODEL SERIAL LAST CAL. DUE CAL. TYPE NUMBER NUMBER EMI Test Receiver Rohde & Schwarz ESU 1302.6005.26 May 20, 2018 May 19, 2019 Pre-Amplifier HP 8447F 2944A07999 May 19, 2018 May 18, 2019 Bilog Antenna Schwarzbeck VULB9163 142 May 19, 2018 May 18, 2019 Loop Antenna ARA PLA-1030/B 1029 May 19, 2018 May 18, 2019 Horn Antenna Schwarzbeck BBHA 9170 BBHA9170399 May 20, 2018 May 19, 2019 Horn Antenna Schwarzbeck BBHA 9120 D143 May 19, 2018 May 18, 2019 Cable Schwarzbeck AK9513 ACRX1 May 20, 2018 May 19, 2019 Cable Rosenberger N/A FP2RX2 May 20, 2018 May 19, 2019 Cable Schwarzbeck AK9513 CRPX1 May 20, 2018 May 19, 2019 Cable Schwarzbeck AK9513 CRRX2 May 20, 2018 May 19, 2019 3.2.3 Radio Frequency Test Equipment EQUIPMENT MFR MODEL SERIAL LASTCAL. DUE CAL. TYPE NUMBER NUMBER Spectrum Analyzer Agilent E4407B 88156318 May 20, 2018 May 19, 2019 Signal Analyzer Agilent N9010A My53470879 May 20, 2018 May 19, 2019 Power meter Anritsu ML2495A 0824006 May 20, 2018 May 19, 2019 Power sensor Anritsu MA2411B 0738172 May 20, 2018 May 19, 2019 Remark: Each piece of equipment is scheduled for calibration once a year. TRF No.:FCC 15.225/A Page 6 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 3.3 DESCRIPTION OF TEST MODES The EUT has been tested under its typical operating condition. The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. The Transmitter was operated in the normal operating mode. The TX frequency was fixed which was for the purpose of the measurements. Pre-defined engineering program for regulatory testing used to control the EUT for staying in continuous transmitting and receiving mode is programmed. TRF No.:FCC 15.225/A Page 7 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 4 FACILITIES AND ACCREDITATIONS 4.1 FACILITIES All measurement facilities used to collect the measurement data are located at Bldg 69, Majialong Industry Zone District, Nanshan District, Shenzhen, China The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.10 and CISPR Publication 22. 4.2 LABORATORY ACCREDITATIONS AND LISTINGS Site Description EMC Lab. : Accredited by CNAS, 2016.10.24 The certificate is valid until 2022.10.28 The Laboratory has been assessed and proved to be in compliance with CNAS-CL01: 2006(identical to ISO/IEC17025: 2005) The Certificate Registration Number is L229 Accredited by TUV Rheinland Shenzhen, 2016.05.19 The Laboratory has been assessed according to the requirements ISO/IEC 17025. Accredited by FCC, August 06, 2018 The certificate is valid until August 07, 2020 Designation Number: CN1204 Test Firm Registration Number: 882943 Accredited by Industry Canada, November 09, 2018 The Conformity Assessment Body Identifier is CN0008. TRF No.:FCC 15.225/A Page 8 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 5 TEST SYSTEM UNCERTAINTY The following measurement uncertainty levels have been estimated for tests performed on the apparatus: Parameter Uncertainty Radio Frequency ±1x10^-5 Conducted Emissions Test ±2.0dB Radiated Emission Test ±2.0dB Occupied Bandwidth Test ±1.0dB All emission, radiated ±3dB Temperature ±0.5℃ Humidity ±3% Measurement Uncertainty for a level of Confidence of 95% TRF No.:FCC 15.225/A Page 9 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 6 SETUP OF EQUIPMENT UNDER TEST 6.1 RADIO FREQUENCY TEST SETUP 1 The component’s antenna ports(s) of the EUT are connected to the measurement instrument per an appropriate attenuator. The EUT is controlled by PC/software to emit the specified signals for the purpose of measurements. Measurement EUT Attenuator Instrument 6.2 RADIO FREQUENCY TEST SETUP 2 The test site semi-anechoic chamber has met the requirement of NSA tolerance 4 dB according to the standards: ANSI C63.10. The test distance is 3m.The setup is according to the requirements in Section 13.1.4.1 of ANSI C63.10-2013 and CAN/CSA-CEI/IEC CISPR 22. Below 30MHz： The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna (loop antenna). The Antenna should be positioned with its plane vertical at the specified distance from the EUT and rotated about its vertical axis for maximum response at each azimuth about the EUT. The center of the loop shall be 1 m above the ground. For certain applications, the loop antenna plane may also need to be positioned horizontally at the specified distance from the EUT. Above 30MHz： The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). (a) Radiated Emission Test Set-Up, Frequency Below 30MHz Turntable 3m EUT Test 0.8 m Receiver Ground Plane Coaxial Cable TRF No.:FCC 15.225/A Page 10 of 28 Report No.: ES190103028W Ver.1.0

Access to the World (b) Radiated Emission Test Set-Up, Frequency Below 1000MHz 3m Turntable 1m to 4m EUT Test 0.8m Receiver Ground Plane Coaxial Cable 6.3 CONDUCTED EMISSION TEST SETUP The mains cable of the EUT (maybe per AC/DC Adapter) must be connected to LISN. The LISN shall be placed 0.8 m from the boundary of EUT and bonded to a ground reference plane for LISN mounted on top of the ground reference plane. This distance is between the closest points of the LISN and the EUT. All other units of the EUT and associated equipment shall be at least 0.8m from the LISN. Ground connections, where required for safety purposes, shall be connected to the reference ground point of the LISN and, where not otherwise provided or specified by the manufacturer, shall be of same length as the mains cable and run parallel to the mains connection at a separation distance of not more than 0.1 m. According to the requirements in ANSI C63.10-2013 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30 MHz using CISPR Quasi-Peak and average detector mode. Reference Ground Reference EUT Auxiliary Ground EMI Receiver Equipment 50Ω 80cm 80cm LISN LISN TRF No.:FCC 15.225/A Page 11 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 6.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM AC Adapter EUT 6.5 SUPPORT EQUIPMENT Item Equipment Mfr/Brand Model/Type No. Note 1 Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. TRF No.:FCC 15.225/A Page 12 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 7 TEST REQUIREMENTS 7.1 20DB BANDWIDTH 7.1.1 Applicable Standard According to FCC Part 2.1049 7.1.2 Conformance Limit No limit requirement. 7.1.3 Test Configuration Test according to clause 6.1 radio frequency test setup 1 7.1.4 Test Procedure The EUT was operating in transmit mode and controlled its channel. Printed out the test result from the spectrum by hard copy function. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. Set to the maximum power setting and enable the EUT transmit continuously Set RBW = 1% occupied bandwidth (3 kHz). Set the video bandwidth (VBW) =3 times RBW (10 kHz). Set Span= approximately 2 to 4 times the occupied bandwidth Set Detector = Peak. Set Trace mode = max hold. Set Sweep = auto couple. The EUT should be transmitting at its maximum data rate. Allow the trace to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 20dB down one side of the emission. Reset the markerdelta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 20dB bandwidth of the emission. If this value varies with different modes of operation (e.g., data rate, modulation format, etc.), repeat this test for each variation. Measure and record the results in the test report. 7.1.5 Test Results Temperature : 28℃ Test By: Andy Humidity : 65 % Modulation Channel Channel Frequency 20dB Bandwidth Limit Verdict Mode Number (MHz) (kHz) (kHz) ASK 0 13.56 8.104 N/A PASS Note: N/A (Not Applicable) TRF No.:FCC 15.225/A Page 13 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 20dB Bandwidth Test Model Channel 0: 13.56MHz ASK Modulation TRF No.:FCC 15.225/A Page 14 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 7.2 FREQUENCY STABILITY 7.2.1 Applicable Standard According to FCC Part 2.1055 7.2.2 Conformance Limit According to part 15.225(e),The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency over a temperature variation of −20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 7.2.3 Test Configuration Test according to clause 6.1 radio frequency test setup 7.2.4 Test Procedures Connect the EUT to frequency analyzer via the antenna connector. EUT was placed at temperature chamber and connected to an external power supply. Temperature and voltage condition shall be tested to confirm frequency stability. (a) Frequency measurements shall be made at the extremes of the specified temperature range and at o intervals of not more than 10 centigrade through the range. A period of time sufficient to stabilize all of the components of the oscillator circuit at each temperature level shall be allowed prior to frequency measurement. The short-term transient effects on the frequency of the transmitter due to keying (except for broadcast transmitters) and any heating element cycling normally occurring at each ambient temperature level also shall be shown. Only the portion or portions of the transmitter containing the frequency determining and stabilizing circuitry need be subjected to the temperature variation test. (b) The frequency stability shall be measured with variation of primary supply voltage as follows: (1) Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment. (2) For hand carried, battery powered equipment, reduce primary supply voltage to the battery operating end point, which shall be specified by the manufacturer. 7.2.5 Test Results TRF No.:FCC 15.225/A Page 15 of 28 Report No.: ES190103028W Ver.1.0

Access to the World Test Condition Channel Operation Channel Freq.Dev. Deviation Limit Temp Frequency Mode Number Voltage (Hz) (ppm) (ppm) (MHz) (V) (℃) -20 13.56 10 0.74 10 -10 13.56 11 0.81 10 0 13.56 8 0.59 10 10 13.56 12 0.88 10 Vnom 20 13.56 13 0.96 10 ASK CH0 30 13.56 9 0.66 10 40 13.56 11 0.81 10 50 13.56 12 0.88 10 5.5V 20 13.56 16 1.18 10 5.0V 20 13.56 19 1.40 10 4.5V 20 13.56 20 1.47 10 VERDICT PASS TRF No.:FCC 15.225/A Page 16 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 7.3 RADIATED SPURIOUS EMISSION 7.3.1 Applicable Standard According to FCC Part 15.225 and 15.209 7.3.2 Conformance Limit Field Strength of Fundamental Emissions and Spectrum Mask Emissions (uV/m)@30m (dBuV/m)@30m (dBuV/m)@10m (dBuV/m)@3m (dBuV/m)@1m Fundamental 15848 84.0 103.1 124.0 143.1 Quasi peak measurement of the fundamental. Spectrum Mask Freq. of (uV/m)@30m (dBuV/m)@30m (dBuV/m)@10m (dBuV/m)@3m (dBuV/m)@1m Emission (MHz) 1.705~13.110 30 29.5 48.6 69.5 88.6 13.110~13.410 106 40.5 59.6 80.5 99.6 13.410~13.553 334 50.5 69.6 90.5 109.6 13.553~13.567 15848 84.0 103.1 124.0 143.1 13.567~13.710 334 50.5 69.6 90.5 109.6 13.710~14.010 106 40.5 59.6 80.5 99.6 14.010~30.000 30 29.5 48.6 69.5 88.6 According to FCC Part15.205, Restricted bands MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 10.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.17725-4.17775 37.5-38.25 1435-1626.5 9.0-9.2 4.20725-4.20775 73-74.6 1645.5-1646.5 9.3-9.5 6.215-6.218 74.8-75.2 1660-1710 10.6-12.7 6.26775-6.26825 123-138 2200-2300 14.47-14.5 8.291-8.294 149.9-150.05 2310-2390 15.35-16.2 8.362-8.366 156.52475-156.52525 2483.5-2500 17.7-21.4 8.37625-8.38675 156.7-156.9 2690-2900 22.01-23.12 8.41425-8.41475 162.0125-167.17 3260-3267 23.6-24.0 12.29-12.293 167.72-173.2 3332-3339 31.2-31.8 12.51975-12.52025 240-285 3345.8-3358 36.43-36.5 12.57675-12.57725 322-335.4 3600-4400 (2) 13.36-13.41 According to FCC Part15.205, the level of any transmitter spurious emission in Restricted bands shall not exceed the level of the emission specified in the following table Restricted Frequency(MHz) Field Strength (μV/m) Field Strength (dBμV/m) Measurement Distance 0.009-0.490 2400/F(KHz) 48.5 - 13.8 300 0.490-1.705 24000/F(KHz) 33.8 – 23.0 30 1.705-30 30 29.5 30 30-88 100 40.0 3 88-216 150 43.5 3 216-960 200 46.0 3 Above 960 500 54.0 3 TRF No.:FCC 15.225/A Page 17 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 7.3.3 Test Configuration Test according to clause 6.2 radio frequency test setup 2 7.3.4 Test Procedure This test is required for any spurious emission that falls in a Restricted Band, as defined in Section 15.205. It must be performed with the highest gain of each type of antenna proposed for use with the EUT. Use the following spectrum analyzer settings: The EUT was placed on a turn table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Span = wide enough to fully capture the emission being measured RBW = 100 kHz for f < 1 GHz(30MHz to 1GHz), 200Hz for f<150KHz(9KHz to 150KHz), 9KHz for f<30MHz(150KHz to 30KHz) VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold Follow the guidelines in ANSI C63.10-2013 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization, etc. A pre-amp and a high pass filter are required for this test, in order to provide the measuring system with sufficient sensitivity. Allow the trace to stabilize. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre-amp gain, etc., is the peak field strength, which must comply with the limit specified in Section 15.35(b). Submit this data. Now set the VBW to 10 Hz, while maintaining all of the other instrument settings. This peak level, once corrected, must comply with the limit specified in Section 15.209. If the dwell time per channel of the hopping signal is less than 100 ms, then the reading obtained with the 10 Hz VBW may be further adjusted by a “duty cycle correction factor”, derived from 20log(dwell time/100 ms), in an effort to demonstrate compliance with the 15.209 limit. Submit this data. Repeat above procedures until all frequency measured was complete. 7.3.5 Test Results TRF No.:FCC 15.225/A Page 18 of 28 Report No.: ES190103028W Ver.1.0

Access to the World  Field Strength of Fundamental Emissions and Spectrum Mask TRF No.:FCC 15.225/A Page 19 of 28 Report No.: ES190103028W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 20 of 28 Report No.: ES190103028W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 21 of 28 Report No.: ES190103028W Ver.1.0

Access to the World  Spurious Emission below 150kHz (9KHz to 150kHz) Temperature: 24℃ Test By: KK Humidity: 53 % Test mode: TX Mode Emission Freq. Ant.Pol. Limit 3m(dBuV/m) Over(dB) Level(dBuV/m) (MHz) H/V PK AV PK AV PK AV -- -- -- -- -- -- -- -- Note: the amplitude of spurious emission that is attenuated by more than 20dB below the permissible limit has no need to be reported. Distance extrapolation factor =40log(Specific distance/ test distance)( dB); Limit line=Specific limits(dBuV) + distance extrapolation factor TRF No.:FCC 15.225/A Page 22 of 28 Report No.: ES190103028W Ver.1.0

Access to the World  Spurious Emission below 30MHz (150KHz to 30MHz) All mode have been tested, and the worst result was report as below: TRF No.:FCC 15.225/A Page 23 of 28 Report No.: ES190103028W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 24 of 28 Report No.: ES190103028W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 25 of 28 Report No.: ES190103028W Ver.1.0

Access to the World  Spurious Emission Above 30MHz (30MHz to 1GHz) TRF No.:FCC 15.225/A Page 26 of 28 Report No.: ES190103028W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 27 of 28 Report No.: ES190103028W Ver.1.0

Access to the World 8 ANTENNA APPLICATION 8.1.1 Antenna Requirement Standard Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier FCC CRF Part 15.203 current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this part are not exceeded. For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 8.1.2 Result PASS. Note: Antenna use a permanently attached antenna which is not replaceable. Not using a standard antenna jack or electrical connector for antenna replacement The antenna has to be professionally installed (please provide method of installation) which in accordance to section 15.203, please refer to the internal photos. TRF No.:FCC 15.225/A Page 28 of 28 Report No.: ES190103028W Ver.1.0


Document Created: 2019-01-21 11:17:48
Document Modified: 2019-01-21 11:17:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC