14_TPS360 TestRpt DXX, r1

FCC ID: 2AJ2B-TPS360

Test Report

Download: PDF
FCCID_3924376

Page 1 of 26 FCC Test Report Report No.: AGC01684180501FE06 FCC ID : 2AJ2B-TPS360 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Handheld Fingerprint Terminal BRAND NAME : N/A MODEL NAME : TPS360 CLIENT : Telepower Communication Co., Ltd DATE OF ISSUE : July 12, 2018 STANDARD(S) : FCC Part 15 Rules TEST PROCEDURE(S) : REPORT VERSION V1.1 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

Report No.: AGC01684180501FE06 Page 2 of 26 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / June 25, 2018 Invalid Original Report V1.1 1st July 12, 2018 Valid Revise Report P5

Report No.: AGC01684180501FE06 Page 3 of 26 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY.................................................................................................................. 4 2. GENERAL INFORMATION .............................................................................................................................. 5 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 6 4. DESCRIPTION OF TEST MODES ................................................................................................................... 7 5. SYSTEM TEST CONFIGURATION .................................................................................................................. 8 5.1. CONFIGURATION OF EUT SYSTEM........................................................................................................ 8 5.2. EQUIPMENT USED IN EUT SYSTEM ....................................................................................................... 8 5.3. SUMMARY OF TEST RESULTS ................................................................................................................ 8 6. TEST FACILITY ................................................................................................................................................ 9 7. RADIATED EMISSION ................................................................................................................................... 10 7.1TEST LIMIT ................................................................................................................................................ 10 7.2. MEASUREMENT PROCEDURE ............................................................................................................. 11 7.3. TEST SETUP............................................................................................................................................ 13 7.4. TEST RESULT.......................................................................................................................................... 14 8. FREQUENCY STABILITY .............................................................................................................................. 17 8.1. MEASUREMENT PROCEDURE ............................................................................................................. 17 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 17 8.3. MEASUREMENT RESULTS .................................................................................................................... 18 9. 20DB BANDWIDTH ........................................................................................................................................ 19 9.1. MEASUREMENT PROCEDURE ............................................................................................................. 19 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 19 9.3. MEASUREMENT RESULTS .................................................................................................................... 20 10. FCC LINE CONDUCTED EMISSION TEST ................................................................................................ 21 10.1. LIMITS OF LINE CONDUCTED EMISSION TEST ................................................................................ 21 10.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST .............................................................. 21 10.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST ........................................... 22 10.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST .......................................................... 22 10.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST .................................................................... 23 APPENDIX A: PHOTOGRAPHS OF TEST SETUP .......................................................................................... 25

Report No.: AGC01684180501FE06 Page 4 of 26 1. VERIFICATION OF CONFORMITY Applicant Telepower Communication Co., Ltd 5 Bld, Zone A, Hantian Technology Town,No.17 ShenHai RD, Nanhai District Address Foshan, China Manufacturer Telepower Communication Co., Ltd 5 Bld, Zone A, Hantian Technology Town,No.17 ShenHai RD, Nanhai District Address Foshan, China Product Designation Handheld Fingerprint Terminal Brand Name N/A Test Model TPS360 Date of test May. 28, 2018~June 25, 2018 Deviation None Condition of Test Sample Normal Report Template AGCRT-US-BR/RF We hereby certify that: The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with radiated emission limits of FCC Rules Part 15.225. Tested By Donjon Huang(Huang June 25, 2018 Dongyang) Reviewed By Bart Xie(Xie Xiaobin) July 12, 2018 Approved By Forrest Lei(Lei Yonggang) July 12, 2018 Authorized Officer

Report No.: AGC01684180501FE06 Page 5 of 26 2. GENERAL INFORMATION A major technical description of EUT is described as following Operation Frequency 13.561MHz Maximum field strength 45.75dBμV/m@3m Modulation ASK Number of channels 1 Antenna Gain 0dBi Antenna Designation Internal Antenna (Met 15.203 Antenna requirement) Hardware Version MAIN-360D-V2.4 Software Version TPS360_V1.0.0 Power Supply DC 3.8V by adapter

Report No.: AGC01684180501FE06 Page 6 of 26 3. MEASUREMENT UNCERTAINTY The uncertainty is calculated using the methods suggested in the “Guide to the Expression of Uncertainty in measurement” (GUM) published by CISPR and ANSI. - Uncertainty of Conducted Emission, Uc = ±3.2 dB - Uncertainty of Radiated Emission below 1GHz, Uc = ±3.9 dB - Uncertainty of Radiated Emission above 1GHz, Uc = ±4.8 dB

Report No.: AGC01684180501FE06 Page 7 of 26 4. DESCRIPTION OF TEST MODES NO. TEST MODE DESCRIPTION 1 Transmitting Note: 1. All the test modes can be supply by adapter, only the result of the worst case was recorded in the report, if no other cases. 2. For Radiated Emission, 3axis were chosen for testing for each applicable mode.

Report No.: AGC01684180501FE06 Page 8 of 26 5. SYSTEM TEST CONFIGURATION 5.1. CONFIGURATION OF EUT SYSTEM Configure: EUT Accessory 5.2. EQUIPMENT USED IN EUT SYSTEM Item Equipment Model No. ID or Specification Remark Handheld Fingerprint 1 TPS360 2AJ2B-TPS360 EUT Terminal 2 Adapter SC/10WA050200US DC 5.0V 2A Accessory 3 Battery HDT-7100 DC3.8V/ 3000mAh Accessory 4 USB N/A N/A Accessory 5.3. SUMMARY OF TEST RESULTS FCC RULES DESCRIPTION OF TEST RESULT §15.209 Radiated Emission Compliant §15.207 Conducted Emission Compliant §15.225 Frequency Tolerance Compliant §15.225 20dB bandwidth Compliant

Report No.: AGC01684180501FE06 Page 9 of 26 6. TEST FACILITY Test Site Attestation of Global Compliance (Shenzhen) Co., Ltd 1-2F., Bldg.2, No.1-4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang, Location Bao’an District B112-B113, Bldg.12, Baoan Bldg Materials Center, No.1 of Xixiang Inner Ring Road, Baoan District, Shenzhen 518012 NVLAP LAB CODE 600153-0 Designation Number CN5028 Attestation of Global Compliance(Shenzhen) Co., Ltd is accredited by National Description Voluntary Laboratory Accreditation program, NVLAP Code 600153-0 TEST EQUIPMENT OF RADIATED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESCI 10096 Jun.20, 2017 Jun.19, 2018 TEST RECEIVER R&S ESCI 10096 Jun.18, 2018 Jun.17, 2019 EXA Signal Aglient N9010A MY53470504 Dec.08, 2017 Dec.07, 2018 Analyzer Horn antenna SCHWARZBECK BBHA 9170 #768 Sep.20, 2017 Sep.19, 2018 preamplifier ChengYi EMC184045SE 980508 Sep.15, 2017 Sep.14, 2018 Active loop antenna A.H. SAS-562B N/A Feb.27, 2018 Feb.26, 2019 (9K-30MHz) Double-Ridged ETS LINDGREN 3117 00034609 May.18, 2017 May.17, 2019 Waveguide Horn Broadband SCHWARZBECK BBV 9718 9718-205 Jun.20, 2017 Jun.19, 2018 Preamplifier Broadband SCHWARZBECK BBV 9718 9718-205 Jun.18, 2018 Jun.17, 2019 Preamplifier ANTENNA SCHWARZBECK VULB9168 D69250 Sep.28, 2017 Sep.27, 2018 TEST EQUIPMENT OF CONDUCTED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESPI 101206 Jun.20, 2017 Jun.19, 2018 TEST RECEIVER R&S ESPI 101206 Jun.18, 2018 Jun.17, 2019 LISN R&S ESH2-Z5 100086 Aug.21, 2017 Aug.20, 2018

® 3 mitues TF MA t ol Attestation of Global Compliance Report No.: AGC01684180501FEO6 Page 10 of 26 7. RADIATED EMISSION 7.A1TEST LIMIT Standard FCC15.225 for within the 13.110MHz—14.010MHz band Frequencies Field Strength at 3O0m Field Strength at 30m Field Strength at 3m (MHz) (micorvolts/meter) (dBuV/m) (dBuV/m) 13.553~13.567 15.848 84 124 13.410~13.553 13.567~13.710 g* PA 90.5 13.110~13.410 13.710~14.010 106 40.5 $o.5 According to 15.35, on any frequency or frequencies below or equal to 1000 MHz, the limits Shown are based on measuring equipment employing a CISPR quasi—peak detector function and related measurement bandwidths, unless otherwise specified the limit on peak radio frequency emissions is 20dB above the maximum permitted average emission limit applicable to the equipment under test. Standard FCC 15.209 for outside of the 13.110MH2z—14.010MHz band Frequency Distance Field Strengths Limit (MHz) Meters u V/m dB(pV)/m 0.009 ~ 0.490 300 2400/F (KkHz) 0.490 ~ 1.705 30 24000/F(kHz) 1.705 ~ 30 30 30 30 ~ 88 3 100 40.0 88 ~ 216 3 150 43.5 216 ~ 960 3 200 46.0 960 ~ 1000 3 500 54.0 Above 1000 3 Other:74.0 dB(uV)/m (Peak) 54.0 dB(uV)/m (Average) Remark: (1) Emission level dBu V = 20 log Emission level u V/m (2) The smaller limit shall apply at the cross point between two frequency bands. (3) Distance is the distance in meters between the measuring instrument, antenna and the closest point of any part of the device or system. The results ’m,6tison| o thisfeaes report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A 6§€ this doc(fia it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed t;!?ttp://www.agc-«drS t.com. o Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC01684180501FE06 Page 11 of 26 7.2. MEASUREMENT PROCEDURE 1. The EUT was placed on the top of the turntable 0.8 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. For emissions above 1GHz, use 1MHz VBW and RBW for peak reading. Then 1MHz RBW and 10Hz VBW for average reading in spectrum analyzer. 7. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum values. 8.If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz. 9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that means the emissions level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. 10. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High - Low scan is not required in this case.

Report No.: AGC01684180501FE06 Page 12 of 26 The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP Receiver Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP

Report No.: AGC01684180501FE06 Page 13 of 26 7.3. TEST SETUP Radiated Emission Test-Setup Frequency Below 30MHz RADIATED EMISSION TEST SETUP 30MHz-1000MHz

Report No.: AGC01684180501FE06 Page 14 of 26 7.4. TEST RESULT RADIATED EMISSION BELOW 30MHZ EUT： Handheld Fingerprint Terminal Model Name TPS360 Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.8V Test Mode ： Mode 1 Polarization : Correction Frequency Reading Result Limit Margin Polar Detector Factor MHz dBuV/m dB/m dBuV/m dBuV/m dB Side/Face 13.5610 51.95 -6.29 45.66 124 -78.34 Side Peak 27.1220 37.86 -7.03 30.83 69.5 -38.67 Side Peak 13.5610 52.04 -6.29 45.75 124 -78.25 Face Peak 27.1220 37.38 -7.03 30.35 69.5 -39.15 Face Peak Note: Other emissions from 9 kHz to 30 MHz are considered as ambient noise. No recording in the test report.

Report No.: AGC01684180501FE06 Page 15 of 26 RADIATED EMISSION 30MHz- 1GHZ EUT： Handheld Fingerprint Terminal Model Name TPS360 Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.8V Test Mode ： Mode 1 Polarization : Horizontal RESULT: PASS

Report No.: AGC01684180501FE06 Page 16 of 26 EUT： Handheld Fingerprint Terminal Model Name TPS360 Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.8V Test Mode ： Mode 1 Polarization : Vertical RESULT: PASS Note: Factor=Antenna Factor + Cable loss, Margin=Result-Limit. The “Factor” value can be calculated automatically by software of measurement system. The mode 1 is the worst case, and only the data of the worst case recorded in this test report.

® A\G 3 TF mize H 1 J Attestation of Global Compliance : Report No.: AGC01684180501FEO6 Page 17 of 26 8. FREQUENCY STABILITY 8.1. MEASUREMENT PROCEDURE 1. Connect EUT RF output port to the Spectrum Analyzer through an RF attenuator 2. Set the EUT Work on the operation frequency. 3. Set SPA Centre Frequency = Operation Frequency, RBW= 1 KHz, VBW >3 X RBW. 4. Set SPA Trace 1 Max hold, then View. 5. The test extreme voltage is to change the primary supply voltage from 85 to 115 percent of the nominal value 6. Extreme temperature rule is —20°C~50°C. 8.2. TEST SET—UP (BLOCK DIAGRAM OF CONFIGURATION) Spectrum Analyzer 1 OVE A H_ HH o «2 O EUT— i + * LOk EoL The results ,n' & virl fii@;}" kreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu/fi it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-% t.com. o Attestatic m ® ) i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 iN¥ Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

AG °s 7 1 & m Attestation of Global Compliance Report No.: AGC01684180501FEO6 Page 18 of 26 8.3. MEASUREMENT RESULTS Operating frequency: 13.561MHz Voltage vs. Frequency Stability (Test Temperature: 20°C) Voltage(V) Fr'\é'gj;fiéir?&fiz) Max'(l\t/l)fi‘g)afi"” Limit(MHz) Conclusion 3.8 13.56139 3.42 13.56138 0.00040 0.001356 PaASS 4.18 13.56140 Temperature vs. Frequency Stability (Test Voltage: 5.0V) Temperature Fr'\é'gj;fiéir?&fiz) Max'(,\afi‘g)afi"” Limit(MHz) Conclusion — 20°C 13.56138 A10°C 13.56137 0°C 13.56137 10°C 13.56139 e Te tamss 0.00039 0.001356 Pass 30°C 13.56136 40°C 13.56138 50°C 13.56139 The results ’r.z6tison| o thisfea ost report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu/® it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-% t.com. o pliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@agc—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

® A\G 3 TF mize H 1 J Attestation of Global Compliance : Report No.: AGC01684180501FEO6 Page 19 of 26 9. 20DB BANDWIDTH 9.1. MEASUREMENT PROCEDURE 1. Connect EUT RF output port to the Spectrum Analyzer through an RF attenuator 2. Set the EUT Work on the operation frequency. 3. Set SPA Centre Frequency = Operation Frequency, RBW= 1 KHz, VBW >3 X RBW. 4. Set SPA Trace 1 Max hold, then View. 9.2. TEST SET—UP (BLOCK DIAGRAM OF CONFIGURATION) Spectrum Analyzer RF Cable SE T EUT The results ,n. virl fii@;}" kreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A this doc@ it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-% t.com. o Attestatic ® ) i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 iN¥ Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC01684180501FE06 Page 20 of 26 9.3. MEASUREMENT RESULTS TEST ITEM 20DB BANDWIDTH TEST MODE Mode1 Test Data (kHz) Criteria Operate channel 2.858 PASS

Report No.: AGC01684180501FE06 Page 21 of 26 10. FCC LINE CONDUCTED EMISSION TEST 10.1. LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz~500kHz 66-56 56-46 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz. 10.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST EUT & Support Units

Report No.: AGC01684180501FE06 Page 22 of 26 10.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. All support equipments received AC120V/60Hz power from a LISN, if any. 5. The EUT received charging voltage by adapter which received 120V/60Hzpower by a LISN.. 6. The test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. 9. The test mode(s) were scanned during the preliminary test. Then, the EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing. 10.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. EUT and support equipment was set up on the test bench as per step 2 of the preliminary test. 2. A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. 3. The test data of the worst case condition(s) was reported on the Summary Data page.

Report No.: AGC01684180501FE06 Page 23 of 26 10.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST LINE CONDUCTED EMISSION TEST LINE -L RESULT: PASS

Report No.: AGC01684180501FE06 Page 24 of 26 Line Conducted Emission Test Line -N RESULT: PASS

Report No.: AGC01684180501FE06 Page 25 of 26 APPENDIX A: PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION TEST SETUP BELOW 1GHz

Report No.: AGC01684180501FE06 Page 26 of 26 FCC LINE CONDUCTED EMISSION TEST SETUP ----END OF REPORT----


Document Created: 2018-07-12 14:38:06
Document Modified: 2018-07-12 14:38:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC