Modular Approval Request

FCC ID: 2AJ2A-RCM24G

Cover Letter(s)

Download: PDF
FCCID_3370640

ISED/FCC Modular Approval Statement Receiver Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Innovation, Science and Economic Development Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Subject: Modular Approval Statement FCC Certification Number: 2AJ2A-RCM24G Date: 27th of March 2017 Only applicable for ISED certification: ISED Company Number: 1000B UPN: RCM24G HVIN (Hardware Version D PMN: (Product Marketing RCM24G Identification Number): Name) HMN: (Host Marketing Name) -- FVIN: (Firmware Version RCM24G_12017USCN Identification Number) TO WHOM IT MAY CONCERN Pursuant to Annex D in RSP-100 Issue 11 January 2016 and CFR § 15.212, we herewith declare for our module. Modular approval requirement Yes No * (a) The radio elements must have the radio frequency circuitry shielded. Physical/discrete and tuning capacitors may be located external to the shield, Yes but must be on the module assembly. *Please provide a detailed explanation if the answer is “No.”: (b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS / part 15 under conditions of excessive data rates or Yes over-modulation. *Please provide a detailed explanation if the answer is “No.”: (c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in Yes the host device which houses the module. *Please provide a detailed explanation if the answer is “No.”: 1

ISED/FCC Modular Approval Statement (d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of highest antenna gain Yes for each type of antenna. *Please provide a detailed explanation if the answer is “No.”: (e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device Yes during testing. *Please provide a detailed explanation if the answer is “No.”: (f) The module shall comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement which are based on the Yes intended configuration/integration in a host. *Please provide a detailed explanation if the answer is “No.”: Only applicable for FCC certification: (g) The module must be equipped with either a permanently affixed label or Yes must be capable of electronically displaying its FCC identification number. *Please provide a detailed explanation if the answer is “No.”: (h) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. Yes If you have any questions, please feel free to contact us at the address shown below Best Regards, _____________________ Mr. Dana B. Craig Corporate Product Regulations & Standards Product Regulatory Engineering Manager Intel Corporation 2200 Mission College Blvd Santa Clara, CA 95054 USA Direct: +1 408 346 5206 Mobile: +1 925 219 6397 Email: dana.craig@intel.com INFO for applicant: LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product, into which the module will be installed, will be maintained, such that full compliance of the end product is always ensured. 2


Document Created: 2017-04-05 19:20:03
Document Modified: 2017-04-05 19:20:03
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC