User Manual

FCC ID: 2AIXN-BS246GB

Users Manual

Download: PDF
FCCID_4363840

BS246GB Structure Sketch Wearing Steps: Use the Micro-USB cable to connect with computer TWS Bluetooth Headset Step① User Manual 1 7 Erect headset and place 2 them into the cochlea Bluetooth headset should be used with the compatible devices 8 which support Bluetooth wireless technology. This allows you to 3 make two calls and enjoy the music streaming at any time freely. 4 9 Please read this user manual carefully before using the headset, 5 10 11 and also read your device’s user manual regarding the Bluetooth 6 function, and pay attention to those important safety and Use the Miro-USB cable to connect with maintenance information. 1）Charging Base-Flip Cover 6）Charging Base-Indicator mobile phone charger Please keep the headset away from children. 2）Charging Base-Inner Cavity 7）Headset-Up Shell 3）Charging Base-Up Shell 4）Charging Base-Bottom Shell 8）Headset-Bottom Shell 9）Driver Shell Step② Note 1: Check the charging device is suitable for the headset or not. Note 2: Use only the supplied charger to charge the headset, if use 5）Charging Base-Micro-USB 10）Headset-Indicator & Slightly rotate headset until it firm other device may violate the validation or the maintenance Charging Port Mic Hole article of this product and may cause danger. Note 3: Do not attempt to force open the built-in battery as this could 11）Touch Bar Specifications damage the headset. Note 4: A fully charged headset will lose its power automatically if left unused. It is recommended to charge the headset every three Bluetooth Version： V5.0 Headset Mode months. Note 5: Do not leave the headset in a too hot or too cold condition (best Bluetooth Profiles Supported： HFP, HSP, A2DP, AVRCP Audio Decoding Protocol： SBC, AAC Status No. Status Charging Base Performance DUT Pairing Mode The indicator light keeps on white. Step③ between -10℃ and 50℃) which may affect the headset's operations although it is fully charged. 1 Make the headset to cochlear edge tightly Note 6: Do not dispose of the headset into fire or water. r. Transmission Power： Class 2 After TWS pairing successfully, L headset prompts “connected”. 1st TWS pairing or pairing after deleted Operation Range： Up to 10 meters 2 TWS Pairing Mode pairing records, indicator light flashes white quickly, when pairing successfully, the indicator light flashes white Frequency Range： 2.4GHz-2.48GHz slowly(The indicator light also will flash white slowly if TWS didn’t pair successfully after 15 seconds). Turning ON/OFF Battery of Headset： 30mAH Li-polymer Battery 3 Standby Mode / Charging Voltage of Headset： DC 5V±0.2V Charging Time of Headset： About 1.5 hours 4 Call Mode / The indicator light of the headset is white when being Method 5 Headset Charging charged, and will turn off automatically after being fully Battery of Base： 300mAH Li-polymer Battery Mode charged Pick up the headsets from the charging base to turn on automatically. Charging Voltage of Base： DC 4.75V-6V The headset prompts “Power on”, and the indicator light Put them back to power off and charge the headset. 6 Power On State flashes white for three times. Charging Time of Base： About 1.5 hours The headset prompts “Power off”, and the indicator light Charging Headset Times from 7 Power Off State flashes white for three times(The indicator light will turn white directly if putting headsets back to charging base to Charging Ways of Headset power off). Charging Base： About 2-3 times Low Voltage 8 The headset prompts “Didu” once every 120 seconds. Alarm State The indicator light of headset is Music Playing Time： (1KHz 88dB) ≥ 3.5 hours white when being charged, and Talk Time： (1KHz 88dB) ≥ 4 hours will turn off automatically after being fully charged Standby Time： ≥ 100 hours Driver： φ10mm Identify according to L&R and Driver sensitivity ： 103±3dB (1KHz) wear the headset (R) and Driver impedance： 16Ω±15％ headset (L) respectively Put the headset (L) (R) to the corresponding position in the bottom Driver frequency ring range： 20Hz-20KHz of the charging base. Dimensions of Charging Method In OFF MODE, press and hold touch bar of headset(R) Base(mm)： L51.5×W51.5×H21.1 Charging Ways of Charging or headset(L) for 2 seconds to turn on. Dimensions of Headset(mm)： L43.1×W16.6×H17.2 Base In ON MODE, press and hold touch bar of headset(R) or Weight(one headset)： About 3.4 g headset(L) for 5 seconds to turn off. 1.When charging base being charged by Micro-USB, Total Weight ： About 35.2 g the indicator light flashes red once every 2 seconds means 1%-25% battery, twice means 25%-50%, 3 *The time mentioned above may vary due to user's operation mode and times means 50%-75% and 4 times means 75%-100%. When full charged, the indicator light device settings. keeps on red. 2. When charging base to charge headset, the indicator light flashes red once every 2 seconds means 1%-25% battery, twice means 25%-50%, 3 times means 50%-75% and 4 times means Headset (L) Headset (R) 75%-100%. 3. When charging base without charging, the Micro-USB charging port indicator light is off.

NOTE: This equipment has been tested and found to comply with TWS Pairing Answer /End a Call Volume +/- the limits for a Class B digital device, pursuant to part 15 of the When call incoming, double touch the touch bar of headset (R) or FCC Rules. These limits are designed to provide reasonable In call mode or music playing mode, touch the touch bar of headset (L) to answer the call, the headset (R) prompts ”Du”. In protection against harmful interference in a residential installation. headset(R) to volume up; touch the touch bar of headset(L) to call mode, double touch the touch bar of headset (R) or headset (L) This equipment generates uses and can radiate radio frequency volume down. Once “DiDu” can be heard from headset R/L when to end the call, the headset (R) prompts ”Du”. energy and, if not installed and used in accordance with the volume is up to maximum or minimum. instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which Forward/Backward Pick up two headsets (without pairing records) from the charging can be determined by turning the equipment off and on, the user is base to power on and the two headsets will enter auto-pairing mode. In music playing mode, long touch the touch bar of headset(R) for encouraged to try to correct the interference by one or more of the (1. If L or R headset didn’t TWS pair successful after 15 seconds, 2 seconds till hearing speaker prompts “Du+Du di” to next song; following measures: the headsets will enter pairing with phone automatically, the indicator Long touch the touch bar of headset(L) for 2 seconds till hearing light of L headset will flash white slowly. 2. Touch the touch bar of L “Du+Du di” to last song. - Reorient or relocate the receiving antenna. or R headset twice to enter TWS pairing mode again.) Reject a call - Increase the separation between the equipment and receiver. Note: 1st TWS pairing or pairing after deleted pairing records, indicator light flashes white -Connect the equipment into an outlet on a circuit different from quickly, when pairing successfully, the indicator light flashes white slowly(The indicator light Touch the touch bar of headset(R) or headset(L) that to which the receiver is connected. also will flash white slowly if TWS didn’t pair successfully after 15 seconds). for 2 seconds to reject the call, the speaker Delete Pairing Records on the Headset -Consult the dealer or an experienced radio/TV technician for help prompts “DiDu”. In OFF mode, touch the touch bar of headset(R) or headset(L) for Changes or modifications not expressly approved by the party 10 seconds and indicator light flashes white for four times quickly. responsible for compliance could void the user's authority to operate the equipment. Voice Assistant This device complies with Part 15 of the FCC Rules. Operation is On standby mode or music playing state, double Maintenance subject to the following two conditions: (1) this device may not cause harmful interference, and On OFF state, touch the touch bar of headset (R) or headset (L) touch the touch bar of headset(R). Touch the • Do not use abrasive cleaning solvents to clean the headset. (2) this device must accept any interference received, including for 2 seconds to power on, the two headsets will enter auto-pairing touch bar of headset(R) or headset(L) to exit. • Do not allow the headset to touch with any sharp objects as this will cause interference that may cause undesired operation. mode. The two headsets will connect with each other after few scratching and damages. seconds, the headset (R) will flash white slowly, and then open the • Please keep headset away from high-temperature, humidity and dust. phone's bluetooth device to search “BS246GB-R”. Operate as the above ways: 1 or 2, and headset (L) prompts Two-call Handling “Connected” after TWS paired successfully. Cell phone begins to search for Bluetooth (Only support the mobile phone which has the function of handling two phones.) Common Faults and Exclusion devices (see the user guide of your phone When you are answering a call, there is another call coming : instructions), and select “BS246GB-R” Faults Reasons Solutions Bluetooth ON 1. Touch the touch bar of headset R/L for 2 seconds to end the current call from bluetooth device list. and answer the incoming call; Can not turn on low battery protection Charging headsets for 1-2 hours BS246GB-R After connected with phone, the headset R Can not turn on by picking Charging base low battery Charging both the headsets and 2. Double touch the touch bar of headset R/L to hold the current call and up the headset /No indicator light when headset being charging base for 1-2 hours will prompt “connected” . answer the incoming call; charged protection No sounds after Wrong pairing Pairing again 3. After the second implementation, double touch the touch bar of headset Note: When the headsets TWS pairing pairing failures, short touch the touch bar of headset R/L to switch between two calls; The two headsets TWS 4. After the second implementation, touch the touch bar of headset R/L for pairing failure/TWS paired Too many pairing records Delete pairing records according (R) and headset ( L ) to enter TWS pairing, successful but can not find to user manual Connect then pair with phone. 2 seconds to end the current call, and double touch the touch bar of the headset(R) headset R/L to end the other call. Charging base without DC power supply doesn’t Check whether the Micro-USB indicator light when charging cable is plugged Note: being charged output power All the above operations have to respect the precondition 1)Checking headset charging interface Headsets without whether has touched to POGO PIN of supported Bluetooth hands free profile V1.5 and Phones are The headsets couldn’t being TWS Reconnected holding function (Network services) from telecom. indicator light when being charged charged in charging base charging base and the location is correct or not. 2)Charging for charging base Method1: Touch the touch bar of headset(R) or headset(L) for 2 seconds to Turning off Low battery Charging headset for 1-2 hours power on→wait for few seconds, the two headsets will connect automatically automatically→the headset will pair with the mobile phone that has Music Pause/Playing Headset echo Volume is too loud or Adjust the volume at phone or ever paired after few seconds →reconnected successfully. environment is noisy change a place In standby mode, double touch the touch bar of Method2: Pick up the headsets from charging base to power on→wait for few Environmental interference Change a place or move to headset(L) to play music. Noise in call caused or distance between close the headset and mobile seconds, the two headsets will connect automatically→the headset On music playing state, double touch the touch headset and mobile is too far will pair with the mobile phone that has ever paired after few Low voice of the calling Adjusting wearing position of seconds →reconnected successfully. bar of headset(L) to PAUSE music. party Wearing headset is wrong headset


Document Created: 2019-06-14 15:44:25
Document Modified: 2019-06-14 15:44:25
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC