15_BS228RK UserMan

FCC ID: 2AIXN-BS228RK

Users Manual

Download: PDF
FCCID_4435142

BS228RK Structure Sketch Wearing Steps: Use the USB cable to connect with computer TWS Bluetooth Headset Step① User Manual 5 Erect headset and place them into the cochlea Bluetooth headset should be used with the compatible devices which support Bluetooth wireless technology. This allows you to 4 7 make two calls and enjoy the music streaming at any time freely. 3 Please read this user manual carefully before using the headset, 1 and also read your device’s user manual regarding the Bluetooth function, and pay attention to those important safety and Use the USB cable to connect with maintenance information. Step② mobile phone charger Please keep the headset away from children. Slightly rotate headset until it firm 2 6 Note 1: Check the charging device is suit to the headset or not. Note 2: Use only the supplied charger to charge the headset, if use other device may violate the validation or the maintenance article of this product and may cause danger. Note 3: Do not attempt to force open the built-in battery as this will Specifications damage the headset. 1）Charging Base Opening Snap 4）Indicator and Mic Hole Note 4: A fully charged headset will lose its power automatically if left 2）Charging Base Indicator 5）Touch Panel unused. It is recommended to charge the headset each three Bluetooth Version： V5.0 3）Micro USB Charging Port 6）Charging Pogo Pin months. Bluetooth Profiles Supported： HFP, HSP, A2DP, AVRCP 7）Ear Tips Note 5: Do not leave the headset in a too hot or too cold condition (best Audio Decoding Protocol： SBC, AAC, APTX Headset Mode Step③ between -10℃ and 50℃) which may affect the headset's operations although it is fully charged. Make the headset to cochlear edge tightly Note 6: Do not dispose of the headset into fire or water. r. Transmission Power： Class 2 Status No. Status Charging Base Performance Pairing Mode wtith The indicator light of headset flashes red and blue Operation Range： Up to 10 meters 1 Frequency Range： 2.4GHz-2.48GHz Bluetooth Device alternately Turning ON/OFF 2 TWS Pairing Mode The indicator light of headset flashes blue quickly Battery of Headset： 45mAH Li-polymer Battery Charging Voltage of Headset： 5V±0.2V The indicator light of the headset flashes blue once every Method 3 Standby Mode 5 seconds Charging Time of Headset： About 1.5 hours When in a call, the indicator light of the headset flashes Pick up the headsets from the charging base to turn on automatically. Call Mode Battery of Base： 420mAH Li-polymer Battery 4 red every 5 seconds Put them back to power off and charge the headset. Charging Voltage of Base： 4.75V-6V Power On 5 The indicator light flashes blue for three times. Charging Time of Base： About 2 hours Charging Headset Times from 6 Power Off The indicator light flashes red for three times. Charging Ways of Headset 7 Low Voltage The indicator light flashes red once every 20 seconds Charging Base： 2-3 times Alarm State The indicator light of headset is Music Playing Time： ≥ 7 hours red when being charged, and Talk Time： ≥ 7 hours will turn off automatically after Charging Base Mode being fully charged Standby Time： About 100 hours Status No. Status Headset Performance Driver： φ6mm 1.The indicator flashes red when being charged. The red Driver sensitivity ： 90±3dB will flash according times until the battery is up to the Charging Mode of corresponding level. Driver impedance： 16Ω±15％ 1 the Charging Base 2. No being charged or discharging to the earbuds, the Put the headset (L) (R) to the corresponding position in the bottom Method Driver frequency ring range： 20HZ-20kHz indicator is off of the charging base. In OFF MODE, touch headset(R) or headset(L) MFB for 2 3.The indicator light is red when being fully charged Dimensions of Charging seconds to turn on. In ON MODE, touch headset(R) or headset(L) MFB for 5 seconds Charging Ways of Charging L80×W33×H31 The indicator flashing red once every 2 seconds means Base(mm)： Charging Base to turn off. 2 25% battery, twice means 50% ,3 times means 75% and 4 Baterry Indication Base Dimensions of Headset(mm)： L26×W16.6×H24.2 times means full battery(100%). Weight(one headset)： About 4.5 g Identify according to L&R and Use the USB charging cable Total Weight ： About 53.8 g wear the headset (R) and to charge *The time mentioned above may vary due to user's operation mode and headset (L) respectively The red will flash according times until the battery is up to the device settings. corresponding level and will be always on when it is fully charged, USB charging port Headset (L) Headset (R)

Music Pause/Playing In standby mode, touch MFB of headset(R or L) to play music and the headset prompts “Di”. TWS Pairing TWS Reconnected On music playing state, double touch MFB of Trouble Shooting headset(R) to PAUSE music and the headset r Method1: Touch MFB of headset(R) or headset(L) for 2 seconds to power on prompts “Di”. Trouble Reasons Solutions →wait for few seconds, the two headsets connect automatically→ Can not turn on low battery protection Charging headsets for 1-2 hours the headset pairs with the mobile phone that has ever paired after Can not turn on by picking Charging base low battery Charging both the headsets and few seconds →reconnected successfully. up the headset /No indicator light when headset being protection charging base for 1-2 hours charged Method2: Pick up the headsets from charging base to power on→wait for few seconds, the two headsets connect automatically→the headset No sounds after Wrong pairing Pairing again pairing Pick up the two headsets from the charging base to power on and pairs with the mobile phone that has ever paired after few seconds The two headsets TWS waiting for few seconds , the two headsets will enter auto-pairing →reconnected successfully. pairing failure/TWS paired Too many pairing records Delete pairing records mode. The two headsets connect with each other after few seconds, successful but can not find Note: the right and left headset will prompt”Dingdong” after TWS the headset (R) alternately flashing red and blue, and then open the reconnected successfully, the right headset prompts”connected” the headset(R) Charging base without Check whether the micro USB phone's bluetooth device to search“BS228RK”. after reconnected with mobile phone successfully indicator light when DC power supply doesn’t charging line is plugged well or charging output power not Note: When the first time to pairing or after delete the pairing TWS wake up Headsets without The headsets couldn’t being 1)Checking headset charging interface whether has touched to POGO PIN of records, the headsets should be paired under 20cm unobstructed. indicator light when charged in charging base charging base and the location is If there's no any operations on headsets for more than one charging correct or not. 2)Charging for charging base minute, it requires to touch the headset to wake it up,then 2s Turning off Low battery Charging headset for 1-2 hours continue for other headset operations. automatically Volume +/- Headset echo Volume is too loud environment is noisy or Adjust the volume at phone change a place Environmental interference Change a place or move the In call mode or music playing mode, single touch MFB of Noise in call caused or distance between headset close to the mobile headset(R) to volume up; single touch MFB of headset(L ) to headset and mobile is too far phone In OFF state, touch MFB key for 2 seconds to power on and volume down,volume up do not have prompt, you will hear “Di” Low voice of the calling Wearing headset is wrong Adjusting wearing position of party headset waiting for few seconds , the two headsets will enter auto-pairing Answer /End a Call form right headset when volume is up to maximum. Headphone operation Unprocessed left headset TWS pairing after pairing is mode. The two headsets connect with each other after few does not work pairing popup cleared and connected to the seconds, the headset (R) alternately flashing red and blue, and When call incoming, touch MFB of headset (R) or headset (L) one volume down do not have prompt, 1. in call mode, the right phone then open the phone's bluetooth device to search “BS228RK”. time to answer the call, when you hear “Di” Play music from the Unprocessed left headset TWS pairing after pairing is headset prompt:”Di” when volume is up to minimum phone when Do as the above ways: 1 or 2 ,and it prompts ”Connected” after In call mode, touch MFB of headset (R) or headset (L) for 2 pairing popup cleared and connected to the .2. music playing mode, the left headset prompt:”Di” when volume you touch the button phone TWS paired successfully: left headset prompts "Left connected" seconds to end the call when you hear “Di +Call End” . is up to minimum in call mode,put one of headset into charging base, to end the call. NOTE: This equipment has been tested and found to comply with and right headset prompts "Right connected-pairing" the limits for a Class B digital device, pursuant to part 15 of the Cell phone begins to search for bluetooth devices Pre/Next Track FCC Rules. These limits are designed to provide reasonable (see the user guide of your phone instructions), and protection against harmful interference in a residential installation. select “BS228RK” from bluetooth device list. In music playing mode, touch MFB of headset(R) for 2 seconds This equipment generates uses and can radiate radio frequency the right headset prompts”Pairing successful”. the and release when the right headset prompt”Di” to next song; energy and, if not installed and used in accordance with the left and right headset prompts :”dingdong”,and the touch MFB of headset(L)for 2 seconds and release when the left instructions, may cause harmful interference to radio Bluetooth ON right headset prompts”Connected”. headset prompt”Di”to previous song. communications. However, there is no guarantee that interference BS228RK After the right headset paired with mobile phone will not occur in a particular installation. If this equipment does successfully, the mobile phone will have a Bluetooth cause harmful interference to radio or television reception, which pairing request (iphone must be connected to the can be determined by turning the equipment off and on, the user is Delete Pairing Records on the Headset Bluetooth interface on the mobile phone), select the encouraged to try to correct the interference by one or more of the match, and the left headset prompts “paring Reject a call In OFF mode, touch MFB of headset(R) or headset(L) about 8 following measures: successful”. seconds when you hear :”Di”, and double touch MFB until hearing (1)Touch MFB of headset(R) or headset(L) for 2 Connect The master-slave switching function cannot be used “Doo” 3 times to delete Pairing Records - Reorient or relocate the receiving antenna. seconds to reject the call, the headset prompts without matching the left earphone (L). - Increase the separation between the equipment and receiver. “Didi, Call Reject”. -Connect the equipment into an outlet on a circuit different from Note: When the headsets TWS pairing (2)When call incoming,put one of headset into that to which the receiver is connected. failures, double touch the headset R and charging base, to end the call Maintenance -Consult the dealer or an experienced radio/TV technician for help headset L to enter TWS pairing, then pair • Do not use abrasive cleaning solvents to clean the headset. with phone. Changes or modifications not expressly approved by the party • Do not allow the headset to touch with any sharp objects as this will cause responsible for compliance could void the user's authority to Master-slave switching scratching and damages. operate the equipment. • Please keep headset away from high-temperature, humidity and dust. The master and slave headset are automatically paired after being turned on. The right headset is the master headset. Voice Dialing This device complies with Part 15 of the FCC Rules. Operation is When the master headset is placed in the charging box, the slave subject to the following two conditions: headset will automatically connect to the mobile phone and can be (1) this device may not cause harmful interference, and On standby mode or music playing state, double used continuously. (2) this device must accept any interference received, including touch the MFB of headset(L) to activate this When the left headset is turn on first and reconnected with mobile interference that may cause undesired operation. function (double touch to start, double touch to phone , the left headset is the master headset. close)the headset prompts “Di”. When the right headset is turn on first and reconnected with Note:This function only supports phone with mobile phone , the right headset is the master headset. voice dialing function Note: Single connection instructions: TWS and mobile pairing records are required for single use.


Document Created: 2019-07-04 14:56:16
Document Modified: 2019-07-04 14:56:16
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC