user manual

FCC ID: 2AIXN-BS188HA

Users Manual

Download: PDF
FCCID_3937613

Structure Sketch Wearing Steps: Use the USB cable to connect with computer Step① BS188HA TWS Bluetooth Headset Erect headset and place User Manual them into the cochlea Bluetooth headset should be used with the compatible devices which support Bluetooth wireless technology. This allows you to make two calls and enjoy the music streaming at any time freely. Use the USB cable to connect with Please read this user manual carefully before using the headset, mobile phone charger and also read your device’s user manual regarding the Bluetooth function, and pay attention to those important safety and Step② Note 1: Check the charging device is suit to the headset or not. Note 2: Use only the supplied charger to charge the headset, if use maintenance information. Slightly rotate headset until it firm other device may violate the validation or the maintenance Please keep the headset away from children. article of this product and may cause danger. 1）Charging Base Openning Snap 5）Indicator and Mic Hole Note 3: Do not attempt to force open the built-in battery as this could damage the headset. 2）Charging Base Indicator for 6）MFB Note 4: A fully charged headset will lose its power automatically if left Headsets 7）Charging Pogo Pin unused. It is recommended to charge the headset each three 3）Charging Base Indicator 8）Ear Tips months. 4）Micro USB Charging Port Note 5: Do not leave the headset in a too hot or too cold condition (best between -10℃ and 50℃) which may affect the headset's operations Specifications Step③ although it is fully charged. Note 6: Do not dispose of the headset into fire or water. r. Bluetooth Version： V4.2 Status No. Status Charging Base Performance Make the headset to cochlear edge tightly. Bluetooth Profiles Supported： HSP, HFP, A2DP, AVRCP 1 The Single Pairing The indicator light of headset(R) flashes red and blue headset(R) alternately Audio Decoding Protocol： SBC After TWS pairing successed, the indicator light of right Turning ON/OFF Transmission Power： Class 2 headset alternately flashing red and blue, when the right 2 TWS Pairing headset pairing successful with mobile phone, the Operation Range： Up to 10 meters Standby Mode indicator light flashes blue once every 10 seconds The indicator light of the right headset flashes blue once Method Frequency Range： 2.4GHz-2.48GHz 3 every 10 seconds In OFF MODE, press and hold headset(R) or headset(L) MFB for When in a call, the indicator light of the right headset Battery of Headset： 55mAH Li-polymer Battery 4 Call Mode flashes red every 10 seconds 2 seconds to turn on. Charging Voltage of Headset： 5V The indicator light of the headset is red when being In ON MODE, press and hold headset(R) or headset(L) MFB for Headset Charging 5 Mode charged, and will turn off automatically after being fully 5 seconds to turn off. Charging Time of Headset： About 1.5 hours charged Battery of Base： 300mAH Li-polymer Battery Charging Voltage of Base： 5V 6 Power Off State Low Voltage The indicator light flashes red for three times. Charging Ways of Headset 7 The indicator light flashes red once every 20 seconds Alarm State The indicator light of headset is red Charging Time of Base： About 1.5 hours when being charged, and will turn Charging Headset Times from off automatically after being fully Status No. Status Headset Performance Charging Base： 2-3 times charged 1 Charging Mode of The indicator will be red during charging and will turn off Music Playing Time： Up to 2 hours the Charging Base after being fully charged Talk Time： Up to 2.5 hours Standby Time： Up to 50 hours Driver： φ6mm Identify according to L&R and Driver sensitivity ： 93±3dB wear the headset (R) and Put the headset (L) (R) to the corresponding position in the bottom Method Driver impedance： 16Ω±15％ headset (L) respectively of the charging base. Pick up the headsets from the charging base to turn on automatically. Driver frequency ring range： 20-20kHz Charging Ways of Charging Put them back and close the case cover to power off. Dimensions of Charging Base Base(mm)： L43×W37.5×H30 Use the USB charging cable to charge Dimensions of Headset(mm)： L24.6×W12.9×H24.1 Weight(one headset)： About 4.6g Total Weight ： About 41g Headset(R) Headset (L) *The time mentioned above may vary due to user's operation mode and device settings. USB charging port

TWS Pairing Answer /End a Call Volume +/- NOTE: This equipment has been tested and found to comply with the limits for When call incoming, short press MFB of headset (R) or headset (L) In call mode or music playing mode, short press MFB of a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are to answer the call when you hear “Du” once；In call mode, long headset(R) to volume up; short press MFB of headset(L ) to press MFB of headset (R) or headset (L) for 2 seconds to end the volume down, when maximum or minimum volume, the speaker designed to provide reasonable protection against harmful interference in a call when you hear “Du” twice. will prompt “Du”. Pick up the two headsets residential installation. This equipment generates uses and can radiate radio from the charging base to frequency energy and, if not installed and used in accordance with the power on and waiting for 10 seconds , the two headsets will instructions, may cause harmful interference to radio communications. enter auto-pairing mode. The Pre/Next Song two headsets connect In music playing mode, long press MFB of headset(R) for 2 However, there is no guarantee that interference will not occur in a particular with each other after few seconds, the headset (R) alternately seconds to next song; long press MFB of headset(L)for 2 seconds installation. If this equipment does cause harmful interference to radio or flashing red and blue, and then open the phone's bluetooth to previous song. function to search. Reject a call television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of Press and hold MFB of headset(R) or 2s headset(L) for 2 seconds to reject the call, the speaker prompts “Du” twice and “call reject”. Delete Pairing Records on the Headset the following measures: - Reorient or relocate the receiving antenna. In OFF mode, press MFB of headset(R) or headset(L) for 10 - Increase the separation between the equipment and receiver. seconds(OFF MODE→On Mode when 2nd second→Delete Pairing Records when 10th second) until hearing “du” 3 times and -Connect the equipment into an outlet on a circuit different from that to which indictors flash red and blue twice at the same time. In OFF state, press MFB key for 2 seconds to power on and Voice Dialing the receiver is connected. waiting for 10 seconds , the two headsets will enter auto-pairing mode. The two headsets connect with each other after few On standby mode or music playing state, double -Consult the dealer or an experienced radio/TV technician for help seconds, the headset (R) alternately flashing red and blue, and click the MFB of headset(L) and you can hear Maintenance Changes or modifications not expressly approved by the party responsible for then open the phone's bluetooth function to search “BS188HA”. “du” once.(This feature only supports phone • Do not use abrasive cleaning solvents to clean the headset. with voice dialing function) compliance could void the user's authority to operate the equipment. Do as the above ways: 1 or 2 , after TWS successfully paired: left • Do not allow the headset to touch with any sharp objects as this will cause headset prompts "left channel" and right headset prompts "right scratching and damages. This device complies with Part 15 of the FCC Rules. Operation is subject to the channel-pairing" • Please keep headset away from high-temperature, humidity and dust. following two conditions: Cell phone begins to search for bluetooth Two-call Handling devices (see the user guide of your phone (1) this device may not cause harmful interference, and (2) this device must (Only support the mobile phone which has the function of handling two for instructions), and select “BS188HA” phones.) Trouble Shooting accept any interference received, including interference that may cause Bluetooth ON from bluetooth device list. When you are answering a call, there is another call coming : BS188HA 1. Long press and hold MFB of headset(R) for 2 seconds to end the current Trouble Reasons Solutions undesired operation. Can not turn on low battery protection Charging headsets for 1-2 hours call and answer the incoming call; Can not turn on by picking Charging both the headsets and 2. Short press MFB of headset(R) to hold the current call and answer the up the headset /No indicator Charging base low battery light when headset being protection charging base for 1-2 hours incoming call; charged 3. After the second implementation, double press MFB of headset(R) to No sounds after Wrong pairing Pairing again pairing switch between two calls; The two headsets TWS Connect 4. After the second implementation, long press MFB of headset(R) for 2 pairing failure/TWS paired Too many pairing records Delete pairing records successful but can not find seconds to end the current call, and long press MFB of headset(R) for 2 the headset(R) seconds to end the other call. Charging base without Note: DC power supply doesn’t Check whether the micro USB indicator light when charging line is plugged well or All the above operations have to respect the precondition that Phone charging output power not TWS Reconnected supported Bluetooth hands free profile V1.5 and Phones are running under call Headsets without The headsets couldn’t being 1)Checking headset charging interface whether has touched to POGO PIN of holding function (Network services) from telecom. indicator light when charging base and the location is charged in charging base correct or not. charging Method1: Press and hold MFB of headset(R) or headset(L) for 2 seconds to 2)Charging for charging base power on→wait for few seconds, the two headsets connect Turning off Low battery Charging headset for 1-2 hours automatically→the headset(R) pairs with the mobile phone that automatically has ever paired after few seconds →reconnected successfully. Music Pause/Playing Headset echo Volume is too loud or Adjust the volume at phone or Method2: Pick up the headsets from charging base to power on→wait for few environment is noisy change a place In standby mode, shortly press MFB of seconds, the two headsets connect automatically→the headset(R) Environmental interference Change a place or move the pairs with the mobile phone that has ever paired after few seconds headset(R) or headset(L) to play music. Noise in call caused or distance between headset close to the mobile headset and mobile is too far phone →reconnected successfully. On music playing state, double-click MFB of Low voice of the calling Adjusting wearing position of headset(R) to PAUSE music. Wearing headset is wrong Note: The headset(R)(L)will prompt "connected", left headset prompts "left party headset channel", the right headset prompts "right channel". After connected But headset(L) can not pause music with mobile phone successfully, the right headset prompts "second independently. device connected”.


Document Created: 2018-03-20 10:52:21
Document Modified: 2018-03-20 10:52:21
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC