FCC SAR_Appendix C_part 2

FCC ID: 2AIRN-002

RF Exposure Info

Download: PDF
FCCID_3974936

® . A In Collaboration with =_‘"/"[‘/, a ues CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn Receiving Pattern (®), 0=0° f=600 MHz, TEM f=1800 MHz, R22 1.0 — j : j A { : j i j : f : j Rollfo] {[—«<7100MHz __—+—600MHz __—+—1800MHz __—+— 2500MHz] Uncertainty of Axial Isotropy Assessment: £1.2% (k=2) Certificate No: Z18—60104 Page 8 of 11

® In Collal ion with — S y Add No.51 Xueyuan Road, Hai ian District, Beijing, 100191, Chima Tel +86—10—62304633—2512 Fax +86—10—62304633—2504 E —mal 1: cttl@chimnattl.com Http://www.chinattl.cn Dynamic Range f(SARneaq) (TEM cell, f 900 MHz) EELbScccclss «442242004242 stt L 2424 EAdd44..... [aiJjreubis induy 144525044 Abwss=sles +¥st sA 4d d ues sn T T Podd l T P P Prd III 1 10 10 10" 10 SAR[mW/cm* AM—)not compensated —@— compensated [aplhou3 o 10° 10‘ SAR[mW/cm*] |___ E®=\not compensated —#&— compensated | Uncertainty of L inearli ty Assessment: £0.9% (k=2) Certificate No 718—60104 Page 9 of 11

4WC \n Collsboration with _‘"/"[‘[, ie a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn Conversion Factor Assessment f=750 MHz, WGLS R9(H_convPF) f=1750 MHz, WGLS R22(H_convF) 3.50 30.00 3.00 25.00 2.50 20.00 %z.oo % g §15.oo & 1.50 KE 6 6 10.00 1.00 0.50 $99 §i6g Es scu yz , §1g Euiss Li ns Ecce Lacl 0 20 40 60 80 100 @0 4000 200 300 400 5p0 & o 2{mm] 2{mm] Deviation from Isotropyin Liquid 1.0 0.8 0.6 0.4 0.2 7 Axis 0.0 —0.2 —0.4 —0.6 —0.8 -1.8 150 * 200 4*’8 250 —1.0 —0.80 —060 —0.40 —0.20 0 020 040 060 080 10 Uncertainty of Spherical Isotropy Assessment: +3.2% (K=2) Certificate No: Z18—60104 Page 10 of 11

—MmiWeeA® n Collsboration with =_‘/"/‘/, a ~iiaaagys" CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn DASY/EASY — Parameters of Probe: EX3DV4 — SN: 3578 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 169.7 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disable Probe Overall Length 337mm Probe Body Diameter 10mm Tip Length 9mm Tip Diameter 2.5mm Probe Tip to Sensor X Calibration Point 1imm Probe Tip to Sensor Y Calibration Point 1mm Probe Tip to Sensor Z Calibration Point 1imm Recommended Measurement Distance from Surface 1.4mm Certificate No: Z18—60104 Page 11 of 11

im® In Collaboration with wl :,/ Bm KI’ /, /,, @=®‘7/"/"‘J, s_p_ e a AhkaA amzemyy7 CALIBRATION LABORATORY CNAs Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China ’? r/ $ v CAUBRATION Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 /,,/,,h‘\“\ CNAS LO570 E—mail: cttl@chinattl.com http:/www.chinattl.en Client UnionTrust Certificate No: 2Z18—60057 CALIBRATION CERTIFICATE Object D2450V2 — SN: 809 Calibration Procedure(s) FP—211—003—01 Calibration Procedures for dipole validation kits Calibration date: March 22, 2018 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22#3)c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRVD 102083 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Power sensor NRV—Z5 100542 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Reference Probe EX3DV4 SN 7464 12—Sep—17(SPEAG,No.EX3—7464_Sep17) Sep—18 DAE4 SN 1525 02—Oct—17(SPEAG,No.DAE4—1525_Oct17) Oct—18 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—18 (CTTL, No.J18X00560) Jan—19 NetworkAnalyzer E5239A MY55491241 29—Jun—17 (CTTL, No.J18X00561) Jun—18 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer é f/ Reviewed by: Lin Hao SAR Test Engineer ‘fifi% Approved by: Qi Dianyuan SAR Project Leader _éqfl/ Issued: March 25, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z18—60057 Page 1 of 8

Ag In Collaboration with x7"7J, Wimaaee>"" a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com http:/Awww.chinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z18—60057 Page 2 of 8

In Collaboration with u@=‘/"/L $_ p__e_ _a _0 jz CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com http:/www.chinattl .Cn Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 2450 MHz +1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 £0.2) °C 40.3 + 6 % 1.84 mho/m + 6 % Head TSL temperature change during test <1.0 °C SAR result with Head TSL SAR averaged over 1 Cm" (1 g) of Head TSL Condition SAR measured 250 mW input power 13.1 mW/g SAR for nominal Head TSL parameters normalized to 1W 52.2 mW /g £ 18.8 % (k=2) SAR averaged over 10 cm (10 g) of Head TSL Condition SAR measured 250 mW input power 6.09 mW /g SAR for nominal Head TSL parameters normalized to 1W 24.3 mW ig £ 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 51.3 £ 6 % 2.00 mho/m + 6 % Body TSL temperature change during test <1.0 °C SA R result with Body TSL SAR averaged over 1_cnm" _(1 g) of Body TSL Condition SAR measured 250 mW input power 12.9 mW/g SAR for nominal Body TSL parameters normalized to 1W 50.7 mW ig + 18.8 % (k=2) SAR averaged over 10 cm (10 g) of Body TSL Condition SAR measured 250 mW input power 5.93 mW /g SAR for nominal Body TSL parameters normalized to 1W 23.5 mW ig + 18.7 % (k=2) Certificate No: Z18—60057 Page 3 of 8

Ag In Collaboration with @77‘J, a *\ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http:/www.chinattl.en Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL Impedance, transformed to feed point 49.50+ 5.650 Return Loss —24.90B Antenna Parameters with Body TSL Impedance, transformed to feed point 50.00+ 71990 Return Loss —22.9d0B General Antenna Parameters and Design Electrical Delay (one direction) 1.067 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z18—60057 Page 4 of 8

!® In Collaboration with e=x‘/"[‘]J, . a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en DASYS5 Validation Report for Head TSL Date: 03.22.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 809 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: £= 2450 MHz; 0 = 1.841 S$/m; sr =40.32; p = 1000 kg/m3 Phantom section: Center Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: e Probe: EX3DV4 — SN7464; ConvF(7.89, 7.89, 7.89); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAEB4 Sn1525; Calibrated: 10/2/2017 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 102.7 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 27.4 W/kg SAR(I g) =13.1 W/kg; SAR(10 g) = 6.09 W/kg Maximum value of SAR (measured) = 21.9 W/kg dB 0 ~4.A6 —8.92 13.39 —17.85 > L« —22.31 0 dB =21.9 W/kg =13.40 dBW/kg Certificate No: Z18—60057 Page 5 of 8

A@ In Collaboration with e=‘[/"]"/, C a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en Impedance Measurement Plot for Head TSL Tr 1 _S11 LogM 10.00dB/ 0.000B 50.00 2450 GHz |—24.91 dB v 40.00 30.00 20.00 10.00 0.00 —10.00 —20.00 —30.00 ~40.00 —50.00 1 Ch1: Start_2.25000 GHz — Stop 2.65000 GHz _TR s11 smitn 1.0000/ 1.000 »11 2450GHz 49540 366.91 pH 5.650 "2 _ >Ch1: Start 225000 GHz — Stop 2.65000 GHz Certificate No: Z18—60057 Page 6 of 8

A® In Collaboration with ©‘/"/‘]J, s p e a q es CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitp://www.chinattl.en DASY5 Validation Report for Body TSL Date: 03.22.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 809 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1: 1 Medium parameters used: £= 2450 MHz; 0 = 1.998 S/m; s, = 51.28; p = 1000 kg/m3 Phantom section: Left Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASYS5 Configuration: e Probe: EX3DV4 — SN7464; ConvF(8.09, 8.09, 8.09); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn1525; Calibrated: 10/2/2017 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 97.63 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 27.2 W/kg SAR(I g) =12.9 W/kg; SAR(10 g) = 5.93 W/kg Maximum value of SAR (measured) = 21.6 W/kg dB 0 ~4.55 —9.09 ~13.64 18.18 22.13 £— 0 dB =21.6 W/kg = 13.34 dBW/kg Certificate No: Z18—60057 Page 7 of 8

i’TfL ;Collaborationewith 3 *\ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en Impedance Measurement Plot for Body TSL Tr 1_S11 LogM 10.004B/ 0.00dB 50.00 2450 GHz |—22.88 dB v 40.00 30.00 20.00 10.00 0.00 —10.00 —20.00 |——yyge—=— —30.00 ~40.00 —50.00 1 Ch1: Start_2.25000 GHz — Stop 2.65000 GHz W511 smitn 1.000u7 1.000 2450 GHz 49.97 0 467.25 pH 7190 2 »Ch1: Start 225000 GHz — Stop 2.65000 GHz | Certificate No: Z18—60057 Page 8 of 8

¢ . w¥ uy Calibration Laboratory of \“\\\\_//I/4 a Schmid & Partner >, S Schweizerischer Kalibrierdienst i\'a\\'eg.—%fi c Service suisse d‘étalonnage Engineering AG 2y Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland * n S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Auden Certificate No: D5GHzV2—1040_Jun18 CALIBRATION CERTIFICATE Object D5GHzV2 — SN:1040 Calibration procedure(s) QA CAL—22.v3 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: June 28, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—026783) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06827 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 3503 30—Dec—17 (No. EX3—3503_Dec17) Dec—18 DAE4 SN: 601 26—0ct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37202783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician | Approved by: KatJa Pokovic Technical Manager %g Issued: June 28, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D5GHzV2—1040_Jun18 Page 1 of 16

s 1 w9 1991 Calibration LabOratOry of i s\s\\\\L\_/L/,I/> S Schweizerischer Kalibrierdienst Schmid & Partner i\hgmfi c Service suisse d‘étalonnage Engineering AG ze u. Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/,1//A\\\\\} S swiss Calibration Service uluilibs Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1040_Jun18 Page 2 of 16

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz + 1 MHz 5300 MHz +1 MHz Frequency 5500 MHz +1 MHz 5600 MHz +1 MHz 5800 MHz +1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 36.1 + 6 % 4.55 mho/m + 6 % Head TSL temperature change during test <0.5 °C se« ar+ SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.88 W/kg SAR for nominal Head TSL parameters normalized to 1W 78.8 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.27 W/ikg SAR for nominal Head TSL parameters normalized to 1W 22.7 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 3 of 16

Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 36.0 + 6 % 4.66 mho/m + 6 % Head TSL temperature change during test <0.5 °C ~——> ««»— SAR result with Head TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.22 W/kg SAR for nominal Head TSL parameters normalized to 1W 82.2 W / kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.36 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 23.6 W/kg + 19.5 % (k=2) Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 35.7 +6 % 4.86 mho/m + 6 % Head TSL temperature change during test <0.5 °C «> s«=> SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.34 W/kg SAR for nominal Head TSL parameters normalized to 1W 83.4 Wikg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.38 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.8 W/kg + 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 4 of 16

Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.5 + 6 % 4.97 mho/m + 6 % Head TSL temperature change during test <0.5°C ~—— ~——— SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.54 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 85.3 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.45 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 24.5 Wikg * 19.5 % (k=2) Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.3 5.27 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.2 + 6 % 5.18 mho/m + 6 % Head TSL temperature change during test <0.5 °C =——— ose— SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.07 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.6 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.30 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 23.0 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 5 of 16

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 47.0 x6 % 5.45 mho/m + 6 % Body TSL temperature change during test <0.5 °C ««+~ «ons SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.58 W/kg SAR for nominal Body TSL parameters normalized to 1W 75.2 Wikg # 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 211 W/kg SAR for nominal Body TSL parameters normalized to 1W 20.9 W/kg x 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.8 +6 % 5.58 mho/m + 6 % Body TSL temperature change during test <0.5 °C ——— SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.70 W/kg SAR for nominal Body TSL parameters normalized to 1W 76.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 216 Wkg SAR for nominal Body TSL parameters normalized to 1W 21.4 W/kg * 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 6 of 16

Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 46.5 + 6 % 5.85 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~—— xee« SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.25 W/kg SAR for nominal Body TSL parameters normalized to 1W 81.9 Wikg £ 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 100 mW input power 2.28 W/kg SAR for nominal Body TSL parameters normalized to 1W 22.6 Wikg + 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.3 +6 % 5.99 mho/m + 6 % Body TSL temperature change during test <0.5 °C ———— ———— SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.21 W/kg SAR for nominal Body TSL parameters normalized to 1W 81.5 W/kg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.29 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.7 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 7 of 16

Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 46.0 + 6 % 6.26 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.79 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.3 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.15 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.3 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1040_Jun18 Page 8 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 50.5 Q — 8.6 jQ Return Loss —21.3 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 49.3 Q — 2.8 jQ Return Loss — 30.8 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 50.2 Q — 6.1 jQ Return Loss — 24.4 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 56.8 Q — 2.0 jQ Return Loss —23.6 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 54.4 Q — 1.0 jQ Return Loss — 27.3 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 49.8 Q — 7.7 jQ Return Loss —22.3 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 49.1 Q —1.8jQ Return Loss —34.1 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 50.5 Q — 4.8 jQ Return Loss —26.3 dB Certificate No: D5GHzV2—1040_Jun18 Page 9 of 16

Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 57.6 Q — 24 jQ Return Loss — 22.6 dB Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 55.1 Q — 1.3 jQ Return Loss — 26.0 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.203 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on December 30, 2005 Certificate No: D5GHzV2—1040_Jun18 Page 10 of 16

DASY5 Validation Report for Head TSL Date: 28.06,2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: DSGHzV2; Serial: DSGHzV2 — SN:1040 Communication System: UID 0 — CW:; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f= 5200 MHz; 0 = 4.55 S/m: &, = 36.1; p = 1000 kg/m‘ . Medium parameters used: f= 5300 MHz; 0 = 4.66 S/m; &, = 36; p = 1000 kg/m‘ , Medium parameters used: f= 5500 MHz: o = 4.86 S/m; &, = 35.7; p = 1000 kg/m* , Medium parameters used: f= 5600 MHz; 0 = 4.97 $/m; &= 35.5; p = 1000 kg/m‘ , Medium parameters used: f= 5800 MHz; 0 = 5.18 S/m; £, = 35.2; p = 1000 kg/m* Phantomsection: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY532 Configuration: * Probe: EX3DV4 — SN3503; ConvF(5.75, 5.75, 5.75) @ 5200 MHz, ConvF(5.5, 5.5, 5.5) @ 5300 MHz, ConvF(5.2, 5.2, 5.2) @ 5500 MHz, ConvF(5.05, 5.05, 5.05) @ 5600 MHz, ConvF(4.96, 4.96, 4.96) @ 5800 MHz; Calibrated: 30.12.2017 * Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601 (5GHz); Calibrated: 26.10.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 e DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 74.83 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 27.8 W/kg SAR(I g) =7.88 W/kg; SAR(10 g) = 2.27 W/kg Maximum value of SAR (measured) = 17.7 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 75.69 V/m; Power Drift =—0.09 dB Peak SAR (extrapolated) = 29.8 W/kg SAR(1 g) = 8.22 W/kg; SAR(10 g) = 2.36 W/kg Maximum value of SAR (measured) = 18.6 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.Amm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 75.52 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 31.8 W/kg SAR(1 g) = 8.34 W/kg; SAR(10 g) = 2.38 W/kg Maximum value of SAR (measured) = 19.3 W/kg Certificate No: D5GHzV2—1040_Jun18 Page 11 of 16

Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 76.52 V/m; Power Drift =—0.01 dB Peak SAR (extrapolated) = 31.9 W/kg SAR(1 g) = 8.54 W/kg; SAR(10 g) = 2.45 W/kg Maximum value of SAR (measured) = 19.8 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 73.34 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 31.6 W/kg SAR(I g) = 8.07 W/kg; SAR(10 g) = 2.3 W/kg Maximum value of SAR (measured) = 19.1 W/kg dB 0 —6.00 —12.00 —18.00 —24.00 —30.00 0 dB = 17.7 W/kg = 12.48 dBW/kg Certificate No: D5GHzV2—1040_Jun18 Page 12 of 16

Impedance Measurement Plot for Head TSL 28 Jun 2018 @7:29:36 (CHZ sii 4 U ors 150477 a —8.6300 "Rs22 0 3.5462 pF 5 200.000 000 MHz * CH1 Markers Del 2: 49.344 a —2.7595 a Ser 5.30000 GHz 3: $0,234 a —6.0545 a 5.50000 GHz 41 56.771 a ~1.9598 a five 5.G0000 GHz 16 St 54.406 a —1.0254 A 5.80000 GHz H1d CH2 CH2 Markers 2:—30,949 d8 tor S.30000 GHz 3t—24.968 dB 5.50000 GHz 41—23.609 dB ee 5.60000 GHz 16 5:—27.260 dB 5.90000 GHz H1d START 5 000.000 000 MHz STOP 6 000.000 000 MHz Certificate No: D5GHzV2—1040_Jun18 Page 13 of 16

DASY5 Validation Report for Body TSL Date: 27.06.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: D5GHzV2; Serial: D5SGHzV2 — SN:1040 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 5.45 $/m; &, = 47; p = 1000 kg/m‘ , Medium parameters used: f = 5300 MHz; 0 = 5.58 $/m; &, = 46.8; p = 1000 kg/m‘, Medium parameters used: f = 5500 MHz: 0 = 5.85 S/m; &, = 46.5; p = 1000 kg/m‘ , Medium parameters used: £ = 5600 MHz; o = 5.99 S/m; &, = 46.3; p = 1000 kg/m‘ , Medium parameters used: f = 5800 MHz; 0 = 6.26 S/m; &, = 46; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.35, 5.35, 5.35) @ 5200 MHz, ConvF(5.15, 5.15, 5.15) @ 5300 MHz, ConvF(4.7, 4.7, 4.7) @ 5500 MHz, ConvF(4.65, 4.65, 4.65) @ 5600 MHz, ConvF(4.53, 4.53, 4.53) @ 5800 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601 (5GHz); Calibrated: 26.10.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 «_ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.84 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 28.1 W/kg SAR(I g) = 7.58 W/kg; SAR(10 g) =2.11 W/kg Maximum value of SAR (measured)= 17.1 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.55 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 29.6 W/kg SAR(1 g) =7.7 W/kg; SAR(10 g) = 2.16 W/kg Maximum value of SAR (measured) = 17.6 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value =69.16 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 33.4 W/kg SAR(1 g) = 8.25 W/kg; SAR(10 g) = 2.28 W/kg Maximum value of SAR (measured) = 19.3 W/kg Certificate No: D5GHzV2—1040_Jun18 Page 14 of 16

Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.09 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 34.0 W/kg SAR(I g) = 8.21 W/kg; SAR(10 g) = 2.29 W/kg Maximum value of SAR (measured) = 19.5 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 63.60 V/m; Power Drift = —0.03 dB Peak SAR (extrapolated) = 33.5 W/kg SAR(I g) =7.79 W/kg; SAR(10 g) = 2.15 W/kg Maximum value of SAR (measured) = 18.8 W/kg 0 dB = 18.8 W/kg = 12.74 dBW/kg Certificate No: D5GHzV2—1040_Jun18 Page 15 of 16

Impedance Measurement Plot for Body TSL 27 Jun 2018 13:35:54 CHZ sii 4o uors {149.781 8 —7.7109a ©.96393 pF 5 200.000 dad MHz * f. CH1 Markers Del 2: 49.148 a .7675 a Cor 5.30000 GHz Avg 16 H1d CH2 CH2 Markers Cor 2:—34.067 dB 5.30000 GHz 3:—26.294 dB 5.50000 GHz 41—22.632 dB Av 5.G0000 GHz 16° §:—25.953 dB 5.80000 GHz H1d START 5 000.000 000 MHz STOP 6 000.000 000 MHz Certificate No: D5GHzV2—1040_Jun18 Page 16 of 16


Document Created: 2018-08-21 16:37:00
Document Modified: 2018-08-21 16:37:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC