RF Test Report

FCC ID: 2AIOHHT1004L16

Test Report

Download: PDF
FCCID_4144104

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 1 of 64 Report No.: SZAWW181122004-01 FCC TEST REPORT For General Procurement, Inc Hyundai Koral_10XL Model No.: Koral_10XL Prepared For : General Procurement, Inc Address : 800 E Dyer Road , Santa Ana, California, United States 92705 Prepared By : Shenzhen Anbotek Compliance Laboratory Limited Address : 1/F, Building D, Sogood Science and Technology Park, Sanwei community, Hangcheng Street, Bao'an District, Shenzhen, Guangdong, China.518102 Tel: (86) 755-26066440 Fax: (86) 755-26014772 Report Number : SZAWW181122004-01 Date of Receipt : Nov. 22, 2018 Date of Test : Nov. 22, 2018~Jan. 02, 2019 Date of Report : Jan. 03, 2019 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 2 of 64 Report No.: SZAWW181122004-01 Contents 1. General Information..................................................................................................................................................5 1.1. Client Information......................................................................................................................................... 5 1.2. Description of Device (EUT)........................................................................................................................ 5 1.3. Auxiliary Equipment Used During Test........................................................................................................ 5 1.4. Description of Test Modes.............................................................................................................................6 1.5. List of channels..............................................................................................................................................7 1.6. Description Of Test Setup..............................................................................................................................8 1.7. Test Equipment List....................................................................................................................................... 9 1.8. Description of Test Facility......................................................................................................................... 10 2. Summary of Test Results........................................................................................................................................ 11 3. Conducted Emission Test........................................................................................................................................12 3.1. Test Standard and Limit...............................................................................................................................12 3.2. Test Setup.....................................................................................................................................................12 3.3. Test Procedure..............................................................................................................................................12 3.4. Test Data...................................................................................................................................................... 12 4. Radiation Spurious Emission and Band Edge........................................................................................................ 17 4.1. Test Standard and Limit...............................................................................................................................17 4.2. Test Setup.....................................................................................................................................................17 4.3. Test Procedure..............................................................................................................................................18 4.4. Test Data...................................................................................................................................................... 19 5. Maximum Peak Output Power Test........................................................................................................................29 5.1. Test Standard and Limit...............................................................................................................................29 5.2. Test Setup.....................................................................................................................................................29 5.3. Test Procedure..............................................................................................................................................29 5.4. Test Data...................................................................................................................................................... 29 6. 20DB Occupy Bandwidth Test............................................................................................................................... 33 6.1. Test Standard................................................................................................................................................33 6.2. Test Setup.....................................................................................................................................................33 6.3. Test Procedure..............................................................................................................................................33 6.4. Test Data...................................................................................................................................................... 33 7. Carrier Frequency Separation Test......................................................................................................................... 37 7.1. Test Standard and Limit...............................................................................................................................37 7.2. Test Setup.....................................................................................................................................................37 7.3. Test Procedure..............................................................................................................................................37 7.4. Test Data...................................................................................................................................................... 37 8. Number of Hopping Channel Test..........................................................................................................................41 8.1. Test Standard and Limit...............................................................................................................................41 8.2. Test Setup.....................................................................................................................................................41 8.3. Test Procedure..............................................................................................................................................41 8.4. Test Data...................................................................................................................................................... 41 9. Dwell Time Test......................................................................................................................................................43 9.1. Test Standard and Limit...............................................................................................................................43 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 3 of 64 Report No.: SZAWW181122004-01 9.2. Test Setup.....................................................................................................................................................43 9.3. Test Procedure..............................................................................................................................................43 9.4. Test Data...................................................................................................................................................... 43 10. 100kHz Bandwidth of Frequency Band Edge Requirement................................................................................ 47 10.1. Test Standard and Limit.............................................................................................................................47 10.2. Test Setup...................................................................................................................................................47 10.3. Test Procedure............................................................................................................................................47 10.4. Test Data.................................................................................................................................................... 47 11. Antenna Requirement............................................................................................................................................52 11.1. Test Standard and Requirement................................................................................................................. 52 11.2. Antenna Connected Construction.............................................................................................................. 52 APPENDIX I -- TEST SETUP PHOTOGRAPH....................................................................................................... 53 APPENDIX II -- EXTERNAL PHOTOGRAPH....................................................................................................... 55 APPENDIX III -- INTERNAL PHOTOGRAPH.......................................................................................................59 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 4 of 64 Report No.: SZAWW181122004-01 TEST REPORT Applicant : General Procurement, Inc Manufacturer : Shen Zhen Cheng Fong Digital-Tech Limited Product Name : Hyundai Koral_10XL Model No. : Koral_10XL Trade Mark : Hyundai Input: DC 5V, 2A(Via adapter Input: AC 100~240V, 50/60Hz, Max: 0.35A; Rating(s) : with DC 3.7V, 5000mAh Battery inside) Test Standard(s) : FCC Part15 Subpart C 2018, Section 15.247 Test Method(s) : ANSI C63.10: 2013 The device described above is tested by Shenzhen Anbotek Compliance Laboratory Limited to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and Shenzhen Anbotek Compliance Laboratory Limited is assumed full of responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC Part 15 Subpart C requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of Shenzhen Anbotek Compliance Laboratory Limited. Date of Test Nov. 22, 2018~Jan. 02, 2019 Prepared by (Engineer / Oliay Yang) Reviewer (Supervisor / Snowy Meng) Approved & Authorized Signer (Manager / Sally Zhang) Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 5 of 64 Report No.: SZAWW181122004-01 1. General Information 1.1. Client Information Applicant : General Procurement, Inc Address : 800 E Dyer Road , Santa Ana, California, United States 92705 Manufacturer : Shen Zhen Cheng Fong Digital-Tech Limited Building A, ChengFong Industrial Area, Huaxing road, Dalang, Longhua, Address : Shen Zhen, China Factory : Shen Zhen Cheng Fong Digital-Tech Limited Address : Building A, ChengFong Industrial Area, Huaxing road, Dalang, Longhua, Shen Zhen, China 1.2. Description of Device (EUT) Product Name : Hyundai Koral_10XL Model No. : Koral_10XL Trade Mark : Hyundai Test Power Supply : AC 240V, 60Hz for adapter/ AC 120V, 60Hz for adapter/ DC 3.7V Battery inside Test Sample No. : S1(Normal Sample), S2(Engineering Sample) Operation Frequency: 2402MHz~2480MHz Transfer Rate: 1/2/3 Mbits/s Product Number of Channel: 79 Channels : Description Modulation Type: GFSK, π/4-DQPSK, 8-DPSK Antenna Type: PIFA Antenna Antenna Gain(Peak): 2.5 dBi Remark: 1) For a more detailed features description, please refer to the manufacturer’s specifications or the User’s Manual. 2) This report is for BDR+EDR module. 1.3. Auxiliary Equipment Used During Test Adapter : Manufacturer: Shenzhen Jihongda Power Co., Ltd. M/N: JHD-AP013U-050200BB-B Input: 100-240V~ 50/60Hz, 0.35A Output: DC 5V, 2000mA Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 6 of 64 Report No.: SZAWW181122004-01 1.4. Description of Test Modes To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 CH00 Mode 2 CH39 Mode 3 CH78 Mode 4 Keeping TX+ Charging Mode For Conducted Emission Final Test Mode Description Mode 4 Keeping TX+ Charging Mode For Radiated Emission Final Test Mode Description Mode 1 CH00 Mode 2 CH39 Mode 3 CH78 Mode 4 Keeping TX+ Charging Mode Note: (1) The measurements are performed at the highest, middle, lowest available channels. (2)The data rate was set in 1Mbps for radiated emission due to the highest RF output power. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 7 of 64 Report No.: SZAWW181122004-01 1.5. List of channels Channel Freq. Channel Freq. Channel Freq. Channel Freq. Channel Freq. (MHz) (MHz) (MHz) (MHz) (MHz) 00 2402 17 2419 34 2436 51 2453 68 2470 01 2403 18 2420 35 2437 52 2454 69 2471 02 2404 19 2421 36 2438 53 2455 70 2472 03 2405 20 2422 37 2439 54 2456 71 2473 04 2406 21 2423 38 2440 55 2457 72 2474 05 2407 22 2424 39 2441 56 2458 73 2475 05 2408 23 2425 40 2442 57 2459 74 2476 07 2409 24 2426 41 2443 58 2460 75 2477 08 2410 25 2427 42 2444 59 2461 76 2478 09 2411 26 2428 43 2445 60 2462 77 2479 10 2412 27 2429 44 2446 61 2463 78 2480 11 2413 28 2430 45 2447 62 2464 12 2414 29 2431 46 2448 63 2465 13 2415 30 2432 47 2449 64 2466 14 2416 31 2433 48 2450 65 2467 15 2417 32 2434 49 2451 66 2468 16 2418 33 2435 50 2452 67 2469 Note: 1. The engineering test program was provided and the EUT was programmed to be in continuously transmitting mode. 2. EUT built-in battery-powered, fully-charged battery use of the test battery. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 8 of 64 Report No.: SZAWW181122004-01 1.6. Description Of Test Setup CE USB AC Line E-1 E-2 EUT Adapter LISN 0.8m Table Table 1.5m RE E-1 0.8m EUT Table 1.5m Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 9 of 64 Report No.: SZAWW181122004-01 1.7. Test Equipment List Cal. Item Equipment Manufacturer Model No. Serial No. Last Cal. Interval L.I.S.N. 1. Artificial Mains Rohde & Schwarz ENV216 100055 Nov. 05, 2018 1 Year Network 2. EMI Test Receiver Rohde & Schwarz ESPI3 101604 Nov. 05, 2018 1 Year 3. RF Switching Unit Compliance Direction RSU-M2 38303 Nov. 05, 2018 1 Year 4. Spectrum Analysis Agilent E4407B US39390582 Nov. 05, 2018 1 Year MAX Spectrum 5. Agilent N9020A MY51170037 Nov. 05, 2018 1 Year Analysis 6. Preamplifier SKET Electronic BK1G18G30D KD17503 Nov. 05, 2018 1 Year Double Ridged Horn Instruments 7. GTH-0118 351600 Nov. 19, 2018 1 Year Antenna corporation Bilog Broadband 8. Schwarzbeck VULB9163 VULB 9163-289 Nov. 19, 2018 1 Year Antenna 9. Loop Antenna Schwarzbeck FMZB1519B 00053 Nov. 19, 2018 1 Year 10. Horn Antenna A-INFO LB-180400-KF J211060628 Nov. 20, 2018 1 Year 11. Pre-amplifier SONOMA 310N 186860 Nov. 05, 2018 1 Year EMI Test Software 12. SHURPLE N/A N/A N/A N/A EZ-EMC RF Test Control 13. YIHENG YH3000 2017430 Nov. 05, 2018 1 Year System 14. Power Sensor DAER RPR3006W 15I00041SN045 Nov. 05, 2018 1 Year 15. Power Sensor DAER RPR3006W 15I00041SN046 Nov. 05, 2018 1 Year MXA Spectrum 16. Agilent N9020A MY51170037 Nov. 05, 2018 1 Year Analysis MXG RF Vector Signal 17. Agilent N5182A MY48180656 Nov. 05, 2018 1 Year Generator 18. Signal Generator Agilent E4421B MY41000743 Nov. 05, 2018 1 Year 19. DC Power Supply IVYTECH IV3605 1804D360510 Apr. 02, 2018 1 Year Constant Temperature 20. ZHONGJIAN ZJ-KHWS80B N/A Nov. 01, 2018 1 Year Humidity Chamber Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 10 of 64 Report No.: SZAWW181122004-01 1.8. Description of Test Facility The test facility is recognized, certified, or accredited by the following organizations: FCC-Registration No.: 184111 Shenzhen Anbotek Compliance Laboratory Limited, EMC Laboratory has been registed and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No. 184111, July 31, 2017. ISED-Registration No.: 8058A-1 Shenzhen Anbotek Compliance Laboratory Limited, EMC Laboratory has been registered and fully described in a report filed with the (ISED) Innovation, Science and Economic Development Canada. The acceptance letter from the ISED is maintained in our files. Registration 8058A-1, June 13, 2016. Test Location Shenzhen Anbotek Compliance Laboratory Limited. at 1/F, Building D, Sogood Science and Technology Park, Sanwei community, Hangcheng Street, Bao'an District, Shenzhen, Guangdong, China.518102 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 11 of 64 Report No.: SZAWW181122004-01 2. Summary of Test Results Standard Section Test Item Result 15.203/15.247(c) Antenna Requirement PASS 15.207 Conducted Emission PASS 15.205/15.209 Spurious Emission PASS 15.247(b)(1) Conducted Peak Output Power PASS 15.247(a)(1) 20dB Occupied Bandwidth PASS 15.247(a)(1) Carrier Frequencies Separation PASS 15.247(a)(1) Hopping Channel Number PASS 15.247(a)(1) Dwell Time PASS 15.247(d) Band Edge PASS Remark: “N/A” is an abbreviation for Not Applicable. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 12 of 64 Report No.: SZAWW181122004-01 3. Conducted Emission Test 3.1. Test Standard and Limit Test Standard FCC Part15 Section 15.207 Maximum RF Line Voltage (dBuV) Frequency Quasi-peak Level Average Level Test Limit 150kHz~500kHz 66 ~ 56 * 56 ~ 46 * 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Remark: (1) *Decreasing linearly with logarithm of the frequency. (2) The lower limit shall apply at the transition frequency. 3.2. Test Setup 3.3. Test Procedure The EUT system is connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC line are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to FCC ANSI C63.10-2013 on Conducted Emission Measurement. The bandwidth of test receiver (ESCI) set at 9kHz. The frequency range from 150kHz to 30MHz is checked. 3.4. Test Data Please to see the following pages. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 13 of 64 Report No.: SZAWW181122004-01 Conducted Emission Test Data Test Site: 1# Shielded Room Operating Condition: Keeping TX+ Charging Mode Test Specification: AC 240V, 60Hz for adapter Comment: Live Line Tem.: 23.4℃ Hum.: 56% Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 14 of 64 Report No.: SZAWW181122004-01 Conducted Emission Test Data Test Site: 1# Shielded Room Operating Condition: Keeping TX+ Charging Mode Test Specification: AC 240V, 60Hz for adapter Comment: Neutral Line Tem.: 23.4℃ Hum.: 56% Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 15 of 64 Report No.: SZAWW181122004-01 Conducted Emission Test Data Test Site: 1# Shielded Room Operating Condition: Keeping TX+ Charging Mode Test Specification: AC 120V, 60Hz for adapter Comment: Live Line Tem.: 23.4℃ Hum.: 56% Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 16 of 64 Report No.: SZAWW181122004-01 Conducted Emission Test Data Test Site: 1# Shielded Room Operating Condition: Keeping TX+ Charging Mode Test Specification: AC 120V, 60Hz for adapter Comment: Neutral Line Tem.: 23.4℃ Hum.: 56% Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 17 of 64 Report No.: SZAWW181122004-01 4. Radiation Spurious Emission and Band Edge 4.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.209 and 15.205 Frequency Field strength Limit Measurement Remark (MHz) (microvolt/meter) (dBuV/m) distance (m) 0.009MHz~0.490MHz 2400/F(kHz) - - 300 0.490MHz-1.705MHz 24000/F(kHz) - - 30 1.705MHz-30MHz 30 - - 30 Test Limit 30MHz~88MHz 100 40.0 Quasi-peak 3 88MHz~216MHz 150 43.5 Quasi-peak 3 216MHz~960MHz 200 46.0 Quasi-peak 3 960MHz~1000MHz 500 54.0 Quasi-peak 3 500 54.0 Average 3 Above 1000MHz - 74.0 Peak 3 Remark: (1)The lower limit shall apply at the transition frequency. (2) 15.35(b), Unless otherwise specified, the limit on peak radio frequency emissions is 20dB above the maximum permitted average emission limit applicable to the equipment under test. This peak limit applies to the total peak emission level radiated by the device. 4.2. Test Setup Figure 1. Below 30MHz Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 18 of 64 Report No.: SZAWW181122004-01 Figure 2. 30MHz to 1GHz Figure 3. Above 1 GHz 4.3. Test Procedure For below 1GHz: The EUT is placed on a turntable, which is 0.8m above the ground plane. For above 1GHz: The EUT is placed on a turntable, which is 1.5m above the ground plane. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT is set 3 meters away from the receiving antenna which is mounted on a antenna tower. The antenna can be moved up and down from 1 to 4 meters to find out the maximum emission level. Rotated the EUT through three orthogonal axes to determine the maximum emissions, both horizontal and vertical polarization of the antenna are set on test. The EUT is tested in 9*6*6 Chamber. The device is evaluated in xyz orientation. For the radiated emission test above 1GHz: Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 19 of 64 Report No.: SZAWW181122004-01 aimed at the emission source for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. For 9kHz to 150kHz, Set the spectrum analyzer as: RBW = 200Hz, VBW =1kHz, Detector= Quasi-Peak, Trace mode= Max hold, Sweep- auto couple. For 150kHz to 30MHz, Set the spectrum analyzer as: RBW = 9KHz, VBW =30kHz, Detector= Quasi-Peak, Trace mode= Max hold, Sweep- auto couple. For 30MHz to 1000MHz, Set the spectrum analyzer as: RBW = 100kHz, VBW =300kHz,Detector= Quasi-Peak, Trace mode= Max hold, Sweep- auto couple. For above 1GHz,Set the spectrum analyzer as: RBW =1MHz, VBW =1MHz, Detector= Peak, Trace mode= Max hold, Sweep- auto couple. RBW =1MHz, VBW =10Hz, Detector= Average, Trace mode= Max hold, Sweep- auto couple. 4.4. Test Data PASS During the test, pre-scan the GFSK, π/4QPSK, 8DPSK modulation, and found the GFSK modulation Middle channel which is the worst case, only the worst case is recorded in the report. The test results of 9kHz-30MHz was attenuated more than 20dB below the permissible limits, so the results don't record in the report. Note: The data is in TX only mode, and this is the worst mode. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 20 of 64 Report No.: SZAWW181122004-01 Test Results (30~1000MHz) Job No.: SZAWW181122004-01 Temp.(℃)/Hum.(%RH): 24.5℃/53%RH Standard: FCC PART 15C Power Source: AC 240V, 60Hz for adapter Test Mode: Keeping TX+ Charging Mode Polarization: Horizontal Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 21 of 64 Report No.: SZAWW181122004-01 Test Results (30~1000MHz) Job No.: SZAWW181122004-01 Temp.(℃)/Hum.(%RH): 24.5℃/53%RH Standard: FCC PART 15C Power Source: AC 240V, 60Hz for adapter Test Mode: Keeping TX+ Charging Mode Polarization: Vertical Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 22 of 64 Report No.: SZAWW181122004-01 Test Results (30~1000MHz) Job No.: SZAWW181122004-01 Temp.(℃)/Hum.(%RH): 24.5℃/53%RH Standard: FCC PART 15C Power Source: AC 120V, 60Hz for adapter Test Mode: Keeping TX+ Charging Mode Polarization: Horizontal Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 23 of 64 Report No.: SZAWW181122004-01 Test Results (30~1000MHz) Job No.: SZAWW181122004-01 Temp.(℃)/Hum.(%RH): 24.5℃/53%RH Standard: FCC PART 15C Power Source: AC 120V, 60Hz for adapter Test Mode: Keeping TX+ Charging Mode Polarization: Vertical Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 24 of 64 Report No.: SZAWW181122004-01 Test Results (1GHz-25GHz) Test Mode: CH00 Test channel: Lowest Peak Value Antenna Preamp Frequency Read Level Cable Loss Level Limit Over Limit Factor Factor Pol. (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) 4804.00 38.42 34.04 6.58 34.09 44.95 74.00 -29.05 V 7206.00 32.57 37.11 7.73 34.50 42.91 74.00 -31.09 V 9608.00 32.13 39.31 9.23 34.79 45.88 74.00 -28.12 V 12010.00 * 74.00 V 14412.00 * 74.00 V 4804.00 42.93 34.04 6.58 34.09 49.46 74.00 -24.54 H 7206.00 34.42 37.11 7.73 34.50 44.76 74.00 -29.24 H 9608.00 31.65 39.31 9.23 34.79 45.40 74.00 -28.60 H 12010.00 * 74.00 H 14412.00 * 74.00 H Average Value Antenna Preamp Frequency Read Level Cable Loss Level Limit Over Limit Factor Factor Pol. (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) 4804.00 27.02 34.04 6.58 34.09 33.55 54.00 -20.45 V 7206.00 21.13 37.11 7.73 34.50 31.47 54.00 -22.53 V 9608.00 20.14 39.31 9.23 34.79 33.89 54.00 -20.11 V 12010.00 * 54.00 V 14412.00 * 54.00 V 4804.00 31.37 34.04 6.58 34.09 37.90 54.00 -16.10 H 7206.00 23.37 37.11 7.73 34.50 33.71 54.00 -20.29 H 9608.00 19.96 39.31 9.23 34.79 33.71 54.00 -20.29 H 12010.00 * 54.00 H 14412.00 * 54.00 H Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 25 of 64 Report No.: SZAWW181122004-01 Test Results (1GHz-25GHz) Test Mode: CH39 Test channel: Middle Peak Value Antenna Preamp Frequency Read Level Cable Loss Level Limit Over Limit Factor Factor Pol. (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) 4882.00 37.28 34.38 6.69 34.09 44.26 74.00 -29.74 V 7323.00 31.81 37.22 7.78 34.53 42.28 74.00 -31.72 V 9764.00 31.45 39.46 9.35 34.80 45.46 74.00 -28.54 V 12205.00 * 74.00 V 14646.00 * 74.00 V 4882.00 41.56 34.38 6.69 34.09 48.54 74.00 -25.46 H 7323.00 33.57 37.22 7.78 34.53 44.04 74.00 -29.96 H 9764.00 30.87 39.46 9.35 34.80 44.88 74.00 -29.12 H 12205.00 * 74.00 H 14646.00 * 74.00 H Average Value Antenna Preamp Frequency Read Level Cable Loss Level Limit Over Limit Factor Factor Pol. (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) 4882.00 26.11 34.38 6.69 34.09 33.09 54.00 -20.91 V 7323.00 20.51 37.22 7.78 34.53 30.98 54.00 -23.02 V 9764.00 19.59 39.46 9.35 34.80 33.60 54.00 -20.40 V 12205.00 * 54.00 V 14646.00 * 54.00 V 4882.00 30.34 34.38 6.69 34.09 37.32 54.00 -16.68 H 7323.00 22.68 37.22 7.78 34.53 33.15 54.00 -20.85 H 9764.00 19.32 39.46 9.35 34.80 33.33 54.00 -20.67 H 12205.00 * 54.00 H 14646.00 * 54.00 H Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 26 of 64 Report No.: SZAWW181122004-01 Test Results (1GHz-25GHz) Test Mode: CH78 Test channel: Highest Peak Value Antenna Preamp Frequency Read Level Cable Loss Level Limit Over Limit Factor Factor Pol. (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) 4960.00 36.37 34.72 6.79 34.09 43.79 74.00 -30.21 V 7440.00 31.21 37.34 7.82 34.57 41.80 74.00 -32.20 V 9920.00 30.91 39.62 9.46 34.81 45.18 74.00 -28.82 V 12400.00 * 74.00 V 14880.00 * 74.00 V 4960.00 40.46 34.72 6.79 34.09 47.88 74.00 -26.12 H 7440.00 32.88 37.34 7.82 34.57 43.47 74.00 -30.53 H 9920.00 30.25 39.62 9.46 34.81 44.52 74.00 -29.48 H 12400.00 * 74.00 H 14880.00 * 74.00 H Average Value Antenna Preamp Frequency Read Level Cable Loss Level Limit Over Limit Factor Factor Pol. (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) 4960.00 25.42 34.72 6.79 34.09 32.84 54.00 -21.16 V 7440.00 20.04 37.34 7.82 34.57 30.63 54.00 -23.37 V 9920.00 19.17 39.62 9.46 34.81 33.44 54.00 -20.56 V 12400.00 * 54.00 V 14880.00 * 54.00 V 4960.00 29.55 34.72 6.79 34.09 36.97 54.00 -17.03 H 7440.00 22.15 37.34 7.82 34.57 32.74 54.00 -21.26 H 9920.00 18.83 39.62 9.46 34.81 33.10 54.00 -20.90 H 12400.00 * 54.00 H 14880.00 * 54.00 H Remark: 1. During the test, pre-scan the GFSK, π/4QPSK, 8DPSK modulation, and found the GFSK modulation is worse case, the report only record this mode. 2. Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor 3. “*” means the test results were attenuated more than 20dB below the permissible limits, so the results don't record in the report. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 27 of 64 Report No.: SZAWW181122004-01 Radiated Band Edge: Test Mode: CH00 Test channel: Lowest Average Value(Vertical) Average Value(Horizontal) Peak Value(Vertical) Peak Value(Horizontal) Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 28 of 64 Report No.: SZAWW181122004-01 Test Mode: CH78 Test channel: Highest Average Value(Vertical) Average Value(Horizontal) Peak Value(Vertical) Peak Value(Horizontal) Remark: 1. During the test, pre-scan the GFSK, π/4QPSK, 8DPSK modulation, and found the GFSK modulation is worse case, the report only record this mode. 2. Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 29 of 64 Report No.: SZAWW181122004-01 5. Maximum Peak Output Power Test 5.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.247 (b)(3) Test Limit 1W or 125mW 5.2. Test Setup 5.3. Test Procedure 1. The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram above, 2. Spectrum Setting: RBW > the 20 dB bandwidth of the emission being measured Span = approximately 5 times the 20 dB bandwidth, centered on a hopping channel VBW  RBW Sweep = auto Detector function = peak Trace = max hold 5.4. Test Data Test Item : Max. peak output power Test Mode : CH Low ~ CH High Test Voltage : DC 3.7V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Channel Frequency Peak Power output Limit Results Modulation (MHz) (dBm) (dBm) 2402 -2.732 30 PASS BDR 2441 0.264 30 PASS BDR 2480 0.522 30 PASS BDR 2402 -3.633 20.96 PASS EDR 2441 -0.775 20.96 PASS EDR 2480 -0.489 20.96 PASS EDR Remark: The EDR was tested on (π/4DQPSK, 8DPSK) modes, only the worst data of (8DPSK) is attached in the following pages. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 30 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR---Low Test Mode: BDR---Middle Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 31 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR---High Test Mode: EDR---Low Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 32 of 64 Report No.: SZAWW181122004-01 Test Mode: EDR---Middle Test Mode: EDR---High Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 33 of 64 Report No.: SZAWW181122004-01 6. 20DB Occupy Bandwidth Test 6.1. Test Standard Test Standard FCC Part15 C Section 15.247 (a)(1) 6.2. Test Setup 6.3. Test Procedure Using the following spectrum analyzer settings: 1. Span= approximately 2 to 3 times the 20dB bandwidth, centered on a hopping channel. 2. Set the RBW = 30 kHz. 3. Set the VBW = 100 kHz. 4. Sweep time = auto couple. 5. Detector function = peak. 6. Trace mode = max hold. 7. Allow trace to fully stabilize. 6.4. Test Data Test Item : 20dB BW Test Mode : CH Low ~ CH High Test Voltage : DC 3.7V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Channel Frequency(MHz) 20dB Down BW(kHz) Modulation Mode Low 2402 937.1 BDR Middle 2441 936.7 BDR High 2480 938.9 BDR Low 2402 1266 EDR Middle 2441 1267 EDR High 2480 1262 EDR Remark: The EDR was tested on (π/4DQPSK, 8DPSK) modes, only the worst data of (8DPSK) is attached in the following pages. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 34 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR---Low Test Mode: BDR---Middle Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 35 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR---High Test Mode: EDR---Low Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 36 of 64 Report No.: SZAWW181122004-01 Test Mode: EDR---Middle Test Mode: EDR---High Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 37 of 64 Report No.: SZAWW181122004-01 7. Carrier Frequency Separation Test 7.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.247 (a)(1) Test Limit >25KHz or >two-thirds of the 20 dB bandwidth 7.2. Test Setup 7.3. Test Procedure The EUT must have its hopping function enabled. Using the following spectrum analyzer settings: 1. Span= Wide enough to capture the peaks of two adjacent channels 2. Set the RBW = 30 kHz. 3. Set the VBW = 100 kHz. 4. Sweep time = auto couple. 5. Detector function = peak. 6. Trace mode = max hold. 7. Allow trace to fully stabilize. 7.4. Test Data Test Item : Frequency Separation Test Mode : CH Low ~ CH High Test Voltage : DC 3.7V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Frequency Separation Read Limit Channel Modulation Mode (MHz) Value (kHz) (kHz) Low 2402 1000 937.1 BDR Middle 2441 1000 936.7 BDR High 2480 1000 938.9 BDR Low 2402 1000 844.0 EDR Middle 2441 1000 844.7 EDR High 2480 1000 841.3 EDR Remark: 1. The limit of mode (EDR) is 2/3 of 20dB BW; 2. The EDR was tested on (π/4DQPSK, 8DPSK) modes, only the worst data of (8DPSK) is attached in the following pages. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 38 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR---Low Test Mode: BDR---Middle Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 39 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR---High Test Mode: EDR---Low Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 40 of 64 Report No.: SZAWW181122004-01 Test Mode: EDR---Middle Test Mode: EDR---High Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 41 of 64 Report No.: SZAWW181122004-01 8. Number of Hopping Channel Test 8.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.247 (a)(1) Test Limit >15 channels 8.2. Test Setup 8.3. Test Procedure The EUT must have its hopping function enabled. Using the following spectrum analyzer setting: 1. Span= the frequency band of operation 2. Set the RBW = 100kHz. 3. Set the VBW = 300kHz. 4. Sweep time = auto couple. 5. Detector function = peak. 6. Trace mode = max hold. 7. Allow trace to fully stabilize. 8.4. Test Data Test Item : Number of Hopping Frequency Test Mode : CH Low ~ CH High Test Voltage : DC 3.7V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Hopping Channel Frequency Quantity of Hopping Channel Quantity of Hopping Channel Range 2402-2480MHz 79 ＞15 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 42 of 64 Report No.: SZAWW181122004-01 BDR Mode EDR Mode Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 43 of 64 Report No.: SZAWW181122004-01 9. Dwell Time Test 9.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.247 (a)(1) Test Limit 0.4 sec 9.2. Test Setup 9.3. Test Procedure The EUT must have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span= zero span, centered on a hopping channel 2. Set the RBW = 1 MHz. 3. Set the VBW = 1 MHz. 4. Sweep time = as necessary to capture the entire dwell time per hopping channel. 5. Detector function = peak. 6. Trace mode = max hold. 7. Allow trace to fully stabilize. 9.4. Test Data Test Item : Time of Occupancy Test Mode : CH Low ~ CH High Test Voltage : DC 3.7V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Package Pulse width Dwell time Time slot length(ms) Limit (s) Modulation Type (ms) (ms) DH1 0.374 time slot length *1600/2 /79 * 31.6 0.4 BDR 119.68 DH3 1.630 time slot length *1600/4 /79 * 31.6 0.4 BDR 260.80 DH5 2.880 time slot length *1600/6 /79 * 31.6 0.4 BDR 307.20 3DH1 0.384 time slot length *1600/2 /79 * 31.6 0.4 EDR 122.88 3DH3 1.630 time slot length *1600/4 /79 * 31.6 0.4 EDR 260.80 3DH5 2.872 time slot length *1600/6 /79 * 31.6 0.4 EDR 306.35 Remark: The EDR was tested on ( π/4DQPSK, 8DPSK) modes, only the worst data of (8DPSK) is attached in the following pages. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 44 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR---DH1 Test Mode: BDR---DH3 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 45 of 64 Report No.: SZAWW181122004-01 Test Mode: BDR—DH5 Test Mode: EDR---3DH1 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 46 of 64 Report No.: SZAWW181122004-01 Test Mode: EDR---3DH3 Test Mode: EDR—3DH5 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 47 of 64 Report No.: SZAWW181122004-01 10. 100kHz Bandwidth of Frequency Band Edge Requirement 10.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.247 (d) in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within Test Limit the band that contains the highest level of the desired power, In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in 15.209(a). 10.2. Test Setup 10.3. Test Procedure The EUT must have its hopping/Non-hopping function enabled. Using the following spectrum analyzer setting: 1. Set the RBW = 100kHz. 2. Set the VBW = 300kHz. 3. Sweep time = auto couple. 4. Detector function = peak. 5. Trace mode = max hold. 6. Allow trace to fully stabilize. 10.4. Test Data Test Item : Band edge Test Mode : CH Low ~ CH High Test Voltage : DC 3.7V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Remark: The EDR was tested on (π/4DQPSK, 8DPSK) modes, only the worst data of (8DPSK) is attached in the following pages. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 48 of 64 Report No.: SZAWW181122004-01 For Hopping Mode BDR mode EDR mode Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 49 of 64 Report No.: SZAWW181122004-01 For Non-Hopping Mode BDR mode -- Lowest BDR mode -- Highest Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 50 of 64 Report No.: SZAWW181122004-01 For Non-Hopping Mode EDR mode -- Lowest EDR mode -- Highest Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 51 of 64 Report No.: SZAWW181122004-01 Conducted Emission Method Test Mode: BDR---Low Test Mode: BDR---Mid Test Mode: BDR---High Test Mode: EDR---Low Test Mode: EDR---Mid Test Mode: EDR---High Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 52 of 64 Report No.: SZAWW181122004-01 11. Antenna Requirement 11.1. Test Standard and Requirement Test Standard FCC Part15 Section 15.203 /247(c) 1) 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but Requirement the use of a standard antenna jack or electrical connector is prohibited. 2) 15.247(c) (1)(i) requirement: Systems operating in the 2400-2483.5 MHz band that is used exclusively for fixed. Point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. 11.2. Antenna Connected Construction The antenna is PIFA Antenna which permanently attached, and the best case gain of the antenna is 2.5 dBi. It complies with the standard requirement. BT Antenna Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 53 of 64 Report No.: SZAWW181122004-01 APPENDIX I -- TEST SETUP PHOTOGRAPH Photo of Conducted Emission Measurement Photo of Radiation Emission Test Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 54 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 55 of 64 Report No.: SZAWW181122004-01 APPENDIX II -- EXTERNAL PHOTOGRAPH Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 56 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 57 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 58 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 59 of 64 Report No.: SZAWW181122004-01 APPENDIX III -- INTERNAL PHOTOGRAPH Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 60 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 61 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 62 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 63 of 64 Report No.: SZAWW181122004-01 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AIOHHT1004L16 Page 64 of 64 Report No.: SZAWW181122004-01 ---------------- End of Report ---------------- Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066440 Fax:(86)755-26014772 www.anbotek.com Code:AB-RF-05-a


Document Created: 2019-03-21 12:35:20
Document Modified: 2019-03-21 12:35:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC