User manual

FCC ID: 2AI87-NT-1203

Users Manual

Download: PDF
FCCID_3100756

Introduction This Wireless Bar Code Scanner is an ingenious device with unique triggger design and excellent performance. It is produced under advanced techniques, with finest chipsets and fully conforms with ergonomics requirements. It is fast and accurate in all 1D codes reading and programmed to better read incomplete or fuzzy codes. It can be widely used in domains including commercial POS system, supermarkets, warehousing and logistics, libraries, banks, transportation, postal service, industrial and manufacturing process management. It is represents an optical combination of proven high property scanning technology and state-of-the-art ergonomics, featuring -- Long-distant and fast transmission, -- Data storage, -- Scan number display, -- Network construction, and -- Application of Anti-jamming Frequency Hopping Technology. This product brings convenience, comfort, high-speed and stability into your bar code scanning. Features and Advantages 1. It could be used as a collector, memory 4M can be extended to 8M 2. Never lose data, clear warning. 3. Intelligent uploading; can choose to upload data of last scans and resume uploading from breakpoints. 4. No-messy-code programmed, data counting, repeated code and out of the base range warning, ID display. 5. Beeper and light indicates if the scanner is out of the base range and scanning will automatically switch to storage mode. 6. Support one to one, one to many, many to one operation; and each base can respond to up to 254 scanners. 7. The terminal communicates with the base at long distance of 150 meters indoor or 300 meters outdoor. 8. 1200MA replaceable lithium battery enables 6-10 hours continuous use after full charge and avoids trouble of returning to factory for replacing battery. Base supports data transmission and battery charging. 9. Germany imported quartz scanning window; effective light penetration, scratch-proof. 10. Supports USB, PS2, RS232 and other designated interface. 1

Unpacking the scanner Your scanner was thoroughly tested and inspected before it was shipped from the factory. The shipping box contains: Wireless Barcode Scanner 1 piece Base 1 piece Battery Pack 1 piece USB cable 1 piece Antenna 1 piece Association card 2 pieces User’s guide 1 copy If any of these items are missing or damaged, please contact your local representative. Retain the shipping box in case you need to ship the scanner. 2

Installing the scanner Connecting the base with USB cable to a computer 1. Connect the base with the cable into the computer’s connector. 2. Windows will automatically install the driver. (If not, you need to install the driver by manual on the host to communicate with the scanner.) 3. When connection is finished, windows will indicate “The hardware has been installed and can be used” and the scanner light will be on. 4. If connection fails, unplug the base and repeat the above steps. Installing the antenna 1. Connect the antenna vertically to the antenna interface on the base. 2. Hold the antenna and tighten it by rotating the nut head clockwise until secure. Notes: To remove the antenna, please operate by inverse steps. Starting wireless scanning Scan the code “start wireless scanning” on the association cards or page 11 of the guide book. Understanding the features Audio and visual indications during data transmission: Successful communication Sound (beeper) Blue light Yes One beep Flash 1 time Flash 3 times (changed into No Three beeps Storage Mode) Storage function: When communication fails (out of base range or signal interference), the reader will store the scanned barcode information automatically. You can also select storage mode by manual. 4M inner memory, can store 40-100 thousand barcodes information. Low power alarm: In case of instant auto-shutdown after startup, please charge the battery as the power is low. Charging: Please fully charge the battery for first time use. Shut down the scanner before charging. When the reader/terminal is on charge, both the blue and the red lights on the base will be on. When charging is finished, only the red one will be on. 3

Performance Parameters Title Parameter Operating Channel 433.79MHz|SM Communication Distance 150 meters indoor; 300 meters outdoor Type of illuminant 650nm laser Operation way Hand-held or bracket-held Bit Error Rate(BER) 1/ 800 million Safety Performance Meet the Grade ⅠNational Criteria for Laser Safety EAN-8，EAN-13，UPC-A，UPC-E，Code 39， Symbologies Code 93，Code 128，EAN128，Coda bar，Industrial 2 of 5，Interleave 2 of 5，Matrix 2 of 5，MSI, China Zip Code etc. Supported Interface RS232, PS2 Keyboard, USB Scanning Method Automatic/ Manual Transmission Rate RS232 Baudrate:2400-38400 Resolution 3mil (0.1mm) Depth of Field 15-800mm(pos0.9) Decode Speed 98 times/second Reading Angle (pitch) 60° Reading Angle (skew) 45 Operating Temperature -20℃-45℃ Storage Temperature -20℃-45℃ Operating Humidity 5%-85% Storage Humidity 5%-85% Power Voltage 5V Working Current 68mA Static Current 48mA Light Intensity Daylight, 4000lux max Electromagnetic Interference Comply with en50081,part1 criteria External Electromagnetic Interference Comply with en50082,part1 criteria Resistance Materials ABS+PC Exterior Dimension Length*Width*Height: Reader: 183mm*75mm*105mm; Base (without antenna): 205mm*100mm*40mm; Weight Reader: 195g; Base (with antenna): 230g 4

Operating the scanner Before you start scanning, make sure: * The terminal has adequate power . * The scanner, cable and the Host are connected. * All cable connections from the base station are secure. To scan bar codes 1. Aim the scanner at a slight angle or pitch to the bar code and press the trigger. 2. If you did not get a good read, adjust the scanner distance from the bar code and the position of the scan beam to make sure you scan every bar and space. The optimum reading stance between scanner and barcode is 15—20 cm. 3. On a successful read, there‘ll be a beep sound, beam dies out. The scanner then transmits barcode message to the Host. 4. To instantly upload data, please make sure that the terminal is in range and associated to the base, or program will automatically turn into storage mode. The terminal communicates with the base at long distance of 150 meters indoor or 300 meters outdoor. >nA A ME TT comec: F [ se 7 $ IRRHHIL— se

Configuring the scanner Play around in the settings menu to configure the device to your exact specifications. Setting Code Description Note The scanner emits 1 beep and the blue light flashes once when the base successfully receives Scan this code to enter signals. normal scanning mode. The scanner emits 3 beep and the blue indicator flashes 3 times Under this mode, data will when the base is not successfully be transmitted to the base associated with scanner. The Normal Mode upon scan. scan result will be automatically (instant upload mode) stored in the scanner. (defaulted) Storage mode will be activated to replace normal mode when the base fails 3 times in a row receiving a signal. Scan this code to enter Under this mode, the red light is Storage mode. on. The blue light will flash when a code is successfully read Under this mode, scans will Storage Mode and stored. be stored in the scanner. Scan this code to uploading stored data. All data in the scanner will be uploaded to the corresponding base. You can scan this code to Upload data (Note: if the data of previous re-upload all stored data when operations are not cleared uploading is stopped due to but still stored in the scanner, improper base association. they will also be uploaded.) (During uploading, the scanner responds as under normal mode) Scanner this code to upload data of the last operation (from the last startup) to the Upload data of last base. operation. 6

Configuring the scanner (continued) You can scan this code to resume uploading from the breakpoint when uploading is broken down (when the base is disconnected or powered off). e.g.: if uploading is broken down Scan this code to resume at the 6th code of total 10 stored uploading data from the codes. Scan this code, the breakpoint. Resume broken upload uploading will continue from the 6th code to the last. During uploading, the beeper indicates the same as under normal mode. (please, see normal mode) Scan this code to show total number of stored Show total number of scans. scans This counts by the number of Scan this code to show carriage return. number of last stored scans. Note: this counter shows Show number of last scans new scan number after “uploading data of last operation”. (use with caution) Scan this code to clear On a successful clearing, the Clear storage scanner storage. blue light flashes once . (To scan this code, please (Available under both normal turn the scanner by 90°) mode and storage mode) 7

Scanner Teansmitter Setting Enter setting Seiting Code Description Note Set working chamel: eg: NT M1=104 set. working Settrnsmiter channel channel 10. Range: 00415, end with 15¢ £ Set transmiter TD: 18. 2# eg: NT 121=1004, ©1008, Set trensmiter TD set. irnsmiter TD 100. Renge: 2sae 1—254, end with # Set transmiter reporing to a named receiver 18. 2# NT 122=2008, ©1008, Set cortesponding receiver eg: set conesponding receiver TD 200 2sae t Range: 1—254, end with # Acivaie or desctivate becper function to indicate whether or not the signals are. received. during uploading data Signals received: 1 beep Signals not received: 3 consecutive 2# beeps as Set beeper Nows: this function will affect seanning speed. Scanning speed is 1 code per second when t is ectivated and 3 codes per second when not Range: 26, 3# Restore: this module tooriginel Restore all original settings transmniter settings HH“ “H ml\ SaveR Exit

Scanner receiver setting Enter setting Setting Code Description Note 0# Set receiver channel: e.g.: NT 1# 211 = 10#, set working channel … Set receiver channel 10. Range: 00-15, end with #. 15# 1# Set receiver ID: e.g.: NT 2# 221=100#, set transmitter ID … 100#, … 200. Range: 1-254, end with #. Set receiver ID 254# Display scanner ID at the receiving end. Enable scanner ID report Do not display scanner ID at Disable scanner ID the receiving end. report Set the delimiter between ID e.g.: scanner and barcode a Tab when ID ID=10, barcode= Set Tab between ID and report is enabled. (Default 12345; display: 10 barcode setting) 12345 Set the delimiter between ID e.g.: scanner and barcode white space when ID=10, barcode= Set White Space between ID report is enabled. 12345; display: 10 ID and barcode 12345 e.g.: scanner Set the delimiter between ID ID=10, barcode= and barcode a “-” when ID Set “-” between ID and 12345; display: report is enabled. barcode 10- 12345 Restore this module to original Restore all original settings. receiver settings Save & Exit Note: After a programming operation, the reader will emit beeps and the light will flash to indicate association to the base. Put the reader close to the base. Unplug the base for a few seconds then plug it back. The light and the beeper will stop on a successful setting. Then the reader will perform on the new setting. 9

Repeated code detection setting Setting code Function Description When this function Enable repeated is activated, the code detection. scanner will give an error alarm with 5 Note: this setting beeps and will be automatically Enable repeated code automatically saved cancel the last detection and remain repeated code if a effective after repeated code is power failure. scanned. Disable repeated code detection. Note: this setting will be automatically saved Disable repeated code and remain detection effective after power failure. The above detecting time can be adjusted by scanning the following codes: (default: 6 seconds) Enter setting Set detecting time 6 seconds Set detecting time 5 seconds Set detecting time 4 seconds Set detecting time 3 seconds Set detecting time 2 seconds Set detecting time 1 seconds 10

Save & Exit Appendix – 1 0 – 9, #, TEST 1234567890 0 1 2 3 4 5 6 7 8 9 # TEST 1234567890 Restore All Original Scanner Settings Start Wireless Scanning 11

Display version information Troubleshooting the scanner This table lists potential problems and their solutions. Symptom Cause Solution When the reader is out of range and not To restore normal mode, scan the normal associated to the base, mode code on the white association The base does not storage mode will be cards or 6th page of this book. On the upload data. automatically other hand, when instant uploading is activated to replace not needed, scan the storage mode code normal instant upload below it to store scans. mode. Scan the code “start wireless scanning” Wireless scanning function on the association cards or page 11 of is not activated. the guide book. Scan the code “restore all original scanner settings” at the right bottom on System is jammed. page 11 and then scan the code “start wireless scanning” below it. 1) scan the first code on page 8 “enter setting”; 2) scan the last second code on page 8 The reader emits “restore all original transmitter a beam but does settings”; not read bar 3) scan the last code on page 8 “save & codes. exit”; The reader could not 4) scan the first code on page 9 “enter associate with the base. setting”; 5) scan the last second code on page 9 “restore all original receiver settings” (the reader will emit beeps); 6) put the reader close to the base; remove the base cable and plug it back after a few seconds; the flashing light and beeper will stop; setting is successful; (if the beeper does not stop 12

after you remove the base cable, repeat the above steps.) 7) scan the last code on page 9 “save & exit”. Troubleshooting the scanner (continued) The reader does not emit The reader is Make sure the battery pack is fully a beam and read bar not receiving charged. Replace the battery pack if codes. power. damaged. The battery pack Charge it. Full charging needs 3-5 hours power is lower than until the light turns into red. 5V. Clean the window with a cotton cloth The scanning moistened with an ammonia and water window is Scanner does not read solution. Dry with a soft cotton cloth or dirty bar codes quickly and allow to air dry. sometimes requires Make sure the bar code is free of dirt multiple scans. The bar code and grime. Then scan at a slight angle or is dirty. pitch to the bar code (see “Operating the Scanner” earlier in this guide). You didn’t scan in Try adjusting the scanning appropriate distance. distance. The scanner was not set up to read Scan another bar code on a similar item. this type of barcode If it scans, clean the bar code giving you symbology, or the trouble. bar code is If you are still unable to scan, restore the Scanner cannot read damaged, covered scanner to original settings. If you still certain bar codes. up, or of poor fail, try using other scanner. quality. The scanner does not Make sure you are scanning the correct recognize the programming bar code and try again. programming bar code 13

scanned. Scanner does not read Reflected light Scan at a slight angle or pitch to the bar “shiny” bar codes. distorts the code (see “Operating the Scanner” scan beam. earlier in this guide). Further operating the scanner Aim Operation To display the total scan number, to Scan the related bar codes in “bar code clear stored data, to upload data. settings” earlier inn this guide. To construct a “many to one” network. 1) scan the code “enter setting” on the top of page 9. 2) scan the code “display transmitter ID” on page 9, the reader will emit beeps. 3) put the reader close to the base and unplug the base for a few seconds and then plug back. The flashing light and the beeper will stop. To identify codes by displaying the 4) scan the last code on page 9 “save & exit”. related reader IDs in a situation that There will be an ID number of this reader “10” a base communicates with many displayed before this reader’s every scanned readers simultaneously. code. (Defaulted: 10) To change the ID to other number, like “200” (range: 1-254) 1) scan the code “enter setting” on the top of page 8. 2) scan the code “set transmitter ID” on page 8. 3) scan the numbers codes on page 11, “2”, “0”, “0” and end with “#”. 4) scan the code on page 8 “save & exit”. Make sure that the base is connected to the host with antenna. To configure different working channels for scanner sets to Set transmitter channel. communicate simultaneously 1) scan the code “enter setting” on page 8. in a network and avoid data 2) scan the code “set transmitter channel” on page interference on hosts. E.g.: 8. channel=6. (Defaulted= 10) 3) scan the number code “6” on page 11 and end with “#”. 14

4) scan the code “save & exit” on page 8 to finish transmitter channel setting. Set receiver channel. 5) scan the code “enter setting” on page 9. 6) scan the code “set receiver channel” on page 9. Further operating the scanner (continued) 7) scan the number code “6” on page 11 and end with “#”. (The number should be the same as setting transmitter channel.) The base will emit beeps. 8) unplug the base for a few seconds then plug back. The flashing light and sounding beeper will stop. If they do not stop, the above setting is not successful. Scan the code “restore all original scanner settings” then the code “start wireless scanning” and repeat the above 8 steps until successful. 9) scan the code “save & exit” on page 9 to finish receiver channel setting. Scan an item code to test data uploading. Maintaining the Scanner Charge the battery at the end of each use and unplug it right when it reaches full charge; overcharging will shorten the battery's lifespan. Water or grime on the window of the scanner will distort the scan beam and impair performance. Moving from one temperature extreme to another causes condensation to form on the optical surfaces that affects scanner performance. • Clean the window with a cotton cloth moistened with an ammonia or water solution. Dry with a soft cotton cloth or allow to air dry. • Do not use a dry tissue to wipe the window. This causes small scratches on the window that will gradually affect performance. • Do not immerse the scanner in water. • Operate and store the scanner and battery pack in an environment with 5% to 15

85% relative humidity. • Operate the battery pack in temperatures within -20°C to 45°C (-4°F to 113°F) and store the battery pack in temperatures within -20°C to 45°C (-4°F to 113°F). • when powered on, the wireless function will automatically send code data each 11s. for your health, turn it off is recommended when not use. Warranty Dear customer; Thank you for purchasing our products. Please keep this card and present when applying for warranty work. Seller name: User name: Tel: Filled/ Tel: sealed Model: Series NO.: by the Add: Seller Purchase Date: Warranty Terms: a. This product is warranted against manufacturing defects in materials for a period of 1 year and workmanship for a period of 2 years from date of Manufacture, under normal use. b. We will repair or replace this unit, at our option and at no charge to the user, with new or reconditioned parts or products if found to be defective during the first year of the warranty period. During the 2nd year of the warranty, there shall be no charge for the workmanship and we will charge for the parts to repair the unit, should a valid warranty claim arise. After the warranty, we will charge the prevailing shop rate to repair the unit. c. All items, within warranty period, shipped to us must be freight prepaid. We will pay the return freight via a service of our technologies’ choice. Customer is responsible for payment of any shipping upgrades. d. Our retailer and we will not assume liability for incidental, consequential, punitive or other similar damages associated with the operation or malfunction of this product. This warranty covers all defects in material and workmanship with the following specified exceptions: (1) Damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) Damage occurring during shipment (claims must be presented to the carrier); (3) Damage to, or deterioration of, any accessory or decorative surface; 16

(4) Damage resulting from failure to follow instructions contained in your owner’s manual; (5) Damage resulting from the performance of repairs or alterations by someone other than an authorized service center; (6) The product has been subjected to abnormal physical or electrical stress, including lightning strike, misuse, negligence, or accident; (7) Applications and uses that this product was not intended. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. 17


Document Created: 2016-08-09 10:44:18
Document Modified: 2016-08-09 10:44:18
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC