User Manual

FCC ID: 2AI7B-W5

Users Manual

Download: PDF
FCCID_4457799

Wireless Charging LED Table Lamp CONGRATULATIONS! You’ve purchased the finest in natural lighting technology with your new OttLite® CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN product. THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED. PRODUCT REGISTRATION FORM CAUTION: Any change or modification to product not expressly recognized by Please complete the enclosed Product Registration Form and return it today by mail. OttLite Technologies voids OttLite’s responsibility for proper function of product. WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete. NOTE: THIS UNIT IS FULLY ASSEMBLED FCC PART 15 Note: This equipment has been tested and found to comply with the limits for a Class 1. Remove lamp from packing, placing lamp body base (A) flat on a steady surface. B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to 2. Connect power adapter input (B) into connector (C) in the rear-bottom of the lamp. provide reasonable protection against harmful interference in a residential installation. 3. Plug the power adapter (D) into a standard household 120V AC outlet. Note: This equipment generates, uses and can radiate radio frequency energy and, if Only use with the supplied power adapter to avoid damage or fire. not installed and used in accordance with the instructions, may cause harmful 4. Turn the lamp ON & OFF using power switch (E) located in the front-upper side of interference to radio communications. However, there is no guarantee that the base (A). Power switch (E) is a “touch” switch that controls the dimmer function interference will not occur in a particular installation. If this equipment does cause for 3 levels of brightness and the color mode function of the lamp. harmful interference to radio or television reception, which can be determined 5. To power LED settings, slightly touch the switch to achieve the following: by turning the equipment off and on, the user is encouraged to try to correct the • turn lamp “ON” to first lower-brightness; touch the switch “once”; interference by one or more of the following measures: • for medium-brightness; touch the switch “twice”; • Reorient or relocate the receiving antenna. • for high-brightness; touch the switch “three-times”; • Increase the separation between the equipment and receiver. • to turn lamp “OFF”; touch the switch “four-times”. • Connect the equipment into an outlet on a circuit different from that to which the 6. This lamp provides three color modes. To adjust lighting color mode slightly receiver is connected. “press and hold” switch (E) for three seconds to switch light color temperature • Consult the dealer or an experienced radio/TV technician for help. F mode; 5000°K, 2700°K, 4000°K. NOTE: 5000°K is the default color mode. Warning: Changes or modifications to this unit not expressly approved by the party 7. Wireless charger for Qi-certified devices (G) is located in the center of base (A). responsible for compliance could void the user’s authority to operate the equipment. See Wireless Charging Instructions section for details. This device complies with Part 15 of the FCC Rules. Operation is subject to the 8. To position the shade simply move the shade (F) as needed to point the light. following two conditions: Please hold the lamp base (A) while adjusting the lamp. (1) this device may not cause harmful interference, and WIRELESS CHARGING INSTRUCTIONS: (2) this device must accept any interference received, including interference that Wireless charging requires a Qi-certified device. To determine if your device is may cause undesired operation. Qi-certified, please visit the Wireless Power Consortium website. “FCC/IC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC's RF exposure guidelines, place at least 20cm from nearby persons." To wirelessly charge a device, perform the following: • Place the device, which supports Qi wireless charging standard, face up on the Déclaration d´eposition aux rayonnements RF FCC/IC attention： D middle of the Qi wireless charging emblem (G). pour maintenir la conformité aux directives d´exposition aux RF de la FCC, • When the device is centered on the Qi wireless charging icon (G), a solid RED placez au moins 20 cm des personnes voisines. light (H) will indicate the device is charging properly. NOTE: If RED light is blinking this indicates the device is not charging and needs to be properly centered. IC CANADA • Check the charge level on your device periodically to determine when device is This device contains licence-exempt transmitter(s)/receiver that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). fully charged. Operation is subject to the following two conditions: CAUTION! DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE. C L’émetteur/récepteur exempt de licence contenu dans le présent appareil est G J H B SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : OR INJURY TO PERSONS 1. L’appareil ne doit pas produire de brouillage; 1. The light shade (F) might get hot after several hours of continuous use. Use caution 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage E when moving the shade. est susceptible d’en compromettre le fonctionnement. 2. Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord. CAN RSS-216/CNR-216 3. Do not alter the plug. CAN ICES-005 (B)/NMB-005 (B) 4. The lamp head included with this unit cannot be replaced by the consumer. 5. INDOOR USE ONLY. POWER ADAPTER SPECIFICATION: Input: AC 100-240V, 50/60 Hz, 1.2A Max NOTE: The important safety instructions appearing in this instruction sheet are not meant Output: 12V DC, 3A with a Male DC Plug to cover all possible conditions and situations that may occur. It must be understood that A common sense, caution, and care must be used with any electrical product. Qi CHARGER SPECIFICATION: Output: up to 10 Watts depending on device CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS THIS LAMP CONTAINS a 5V, 2,1A USB output port (J) located on the bottom rear of Wireless Charging LED Table Lamp DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE lamp. USB port can charge items such as tablets, cellular phones, etc. CSAQA4KZ W5 AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY. The “Qi” symbol is a trademark of the Wireless Power Consortium INS190516 REV091719


Document Created: 2019-09-17 14:38:58
Document Modified: 2019-09-17 14:38:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC