Users Manual

FCC ID: 2AI7B-M2A1

Users Manual

Download: PDF
FCCID_4260434

LED Bluetooth® Speaker Lamp CONGRATULATIONS! 3. Never use with an extension cord unless the plug can be fully inserted You‘ve purchased the finest in natural lighting technology with your new into the receptacles in the extension cord. OttLite® product. 4. Do not alter the plug. 5. The lamp head included with this unit cannot be replaced by the PRODUCT REGISTRATION FORM consumer. Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OftLite.com/Awarranty NOTE: The important safety instructions appearing in this instruction NOTE: THIS UNITIS FULLYASSEMBLED sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and 1. Remove lamp from packing placing lamp body base (A) flat on a care must be used with any electrical product. steady surface. 2. Connect the AC Adapter input (H) into connector (J) in the rear—bottom of the lamp. 3. Plug the A/C adapter (G) into a standard household 120V AC outlet. CAUTION ' IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE Note: Only use with the supplied AC adapter to avoid damage IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS or fire. SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. 4. Turn the lamp ON & OFF using power "touch" switch (C) located in the INDOOR USE ONLY. front—upper side of base (A). 5. Lamp includes 5 LED brightness settings. To adjust LED brightness settings, slightly touch "up"or "down" arrows (E) located next to power switch (C). Upon turning ON lamp, it will initially set at the 3rd FCC PART 15 Note: This equipment has been tested and found to comply with the Imits for a Class B LED brightness setting. dlgital device, pursuant to Part 15 of the FCC rules. These Iimitsare designed to provide 6. This lamp features a stereo speaker (M) with Bluetooth pairing and reasonable protection against harmful interference in residentiainstalation. This auxiliary device direct plug—in capabilty to play music directly through equipment generates, uses and can radiate radio frequency energy and, if not installed the speaker. Auxilfary input requires a 8.5mm audio cable (not included) and used in accordance with the instructions, may cause harmful interference to radio to connect your device to the unit. communications. However, there is no quarantee that the interference will not occur in 7. Bluetooth pairing can be turned ON & OFF by using Bluetooth touch a particular installtion. Ifthis equipment does cause harmful interference to radio or switch (B) located below power switch (C). To engage Bluetooth television reception, which can be determined by turning the equipment off and on, the user pairing operation perform the following: is encouraged to tryto correct the interference by one or more of the following measures * Press and hold Bluetooth touch switch (B) to engage speaker (M) * Reorient or relocate the receiving antenna. until Bluetooth indicator light (N) begins to flash continually "flash" * Increase the separation between the equipment and receiver. meaning it is "ready to pair"; * Connect the equipment into an outlet on a circuit different from that of * Engage desired handheld device (such as mobile phone, the receiver. tablet, etc.) by searching for device"OttLite M2A" (LED Bluetooth® * Consultthe dealer or an experienced radio/TV technician for help Speaker Lamp) on handheld device Bluetooth settings, click the device name to successfully pair and connectthe CAN ICES—3 (B)/NMB—3 (B) Bluetooth function. * The blue light will "slowly" flash showing a successful connection has been made. CAUTION «Any change or modification to product not expressly 8. Perform the following to play music directly to speaker using auxiliary recognized by OftLite Technologies voids OftLite‘s responsibility for device plug—in feature: proper function of product. * Press and hold Bluetooth touch switch (B) to engage speaker (M) until Bluetooth indicator light (N) begins to flash. At this time the AC/DC ADAPTOR speaker is in the default Bluetooth "ready to pair" mode. Input: AC 100—240V, 50/60 Hz, 0.8A * Insert 3.5mm audio cable (not included) into AUX connection (K) in Output: 12V DC, 2.0A with a Male DC Plug the rear—bottom of the lamp. 9. Quickly press touch switches "+"and *—* (D) for volume adjustment. Output power: SW + SW Touch switch "+"increases volume and touch switch "—* reduces volume. Speaker: 2 inch, 4 ohms 10. Press and hold touch switches *+"and *—"(D) to make a song track Bluetooth v2.1 change. Press and hold touch switch "+" to advance to the next song. 3.5mm audio cable is required for direct plug—in connection Press and hold touch switch *—" to go back to the previous song. (not included) NOTE: Skip function for song track change is only applicable to Bluetooth mode. THIS LAMP CONTAINS a SV—2.1 USB output () located on the base of the 11. To reposition the light, hold base (A) steady then grasp and adjust lamp. USB port can charge such items as tablets, cellular phones, etc. either lamp arm (F) or shade (P) depending on needed position. 12. Refer to Diagrams 1 and 2 for lamp maximum adjustment range. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. NOTE: DO NOT FORCE the shade or lamp body rotation outside allowable adjustment range as excessive adjustment may cause damage. SAFETY WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS 1. Turn lamp off and WAIT UNTIL LAMP HEAD (P) IS COOL before handling. 2. The LED panel (L) might get hot after several hours of continuous use, DO NOT place your hands directly on LED light panel. LED Bluetooth® Speaker Lamp DS2GSZ DS200Z M2A INS160267 REVO62216

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exempts de licence d'Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) Cet dispositif ne peut causer des interférences; et (2) Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.


Document Created: 2016-09-22 15:29:04
Document Modified: 2016-09-22 15:29:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC