user manual

FCC ID: 2AHST-RGBW

Users Manual

Download: PDF
FCCID_4283453

LED Controllers SR-ZG9101FA-RGBW 09.ZG3FW.04282 3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part "Factory Reset Manually". Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller. Important: Read All Instructions Prior to Installation Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15 seconds timeout, repeat the operation. Function introduction Step 4: Connected light will blink 5 times L OUTPUT INPUT N 12V/24V/36V CV PSU V- and then stay solid on, then the device V+ G 12-36VDC Input AC Power 50/60Hz will appear in your controller's menu and ZigBee RGBW Receiver can be controlled through controller or Common Anode output (+) hub interface. 1/R- CH 1 (R) output (-) LED OUTPUT ZigBee RGBW Lighting Device Prog. 2/G- CH 2 (G) output (-) V+ R- V+ R- CH 3 (B) output (-) 1/R- 3/B- LED 2/G- 4/W- Prog. 3/B- CH 4 (W) output (-) 4/W- G- B- G- B- W- W- Program Key: short press to switch on/off load, press and hold down to increase/decrease light intensity 4. TouchLink to a Zigbee Remote Note: W channel can only be turned on through color temperature control command since Zigbee only has tunable white control. Color temperature control will mix RGB channels as 1 channel white and then make color Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together commissioning immediately, 180S timeout, repeat the operation. with RGB channels. Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee Product Data network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout, repeat the operation. No. Input Voltage Output Current Output Power Output Type Dimension (LxWxH) L Step 4: There shall be OUTPUT INPUT 12V/24V/36V V- N 1 12-36VDC 4CH, 5A/CH 240-720W Constant voltage 170x53.4x28mm G CV PSU V+ indication on the AC Power 2 12-36VDC 4CH, 0.35A/CH 16.8-50.4W Constant current 170x53.4x28mm 50/60Hz remote for successful 3 12-36VDC 4CH, 0.7A/CH 33.6-100.8W Constant current 170x53.4x28mm link and connected light will flash twice. < 10cm • ZigBee RGBW LED light device based on latest ZigBee 3.0 protocol ZigBee RGBW Lighting Device V+ R- V+ R- 1/R- LED 2/G- • Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights Zigbee Prog. 3/B- 4/W- G- G- B- B- • W channel can only be controlled through color temperature control command Remote W- W- • Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the Step 2: Bring the remote or touch panel within 10cm of the lighting device. 4th channel white Step 3: Set the remote or touch panel into Touchlink commissioning, • ZigBee end device that supports Touchlink commissioning please refer to corresponding remote or touch panel manual to learn how . • Supports self-forming zigbee network without coordinator Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote. • Supports find and bind mode to bind a ZigBee remote 2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes. • Supports zigbee green power and can bind max. 20 zigbee green power remotes 3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink. • Compatible with universal ZigBee gateway products 4) After TouchLink, the device can be controlled by the linked remotes. • Waterproof grade: IP20 5. Removed from a Zigbee Network through Coordinator or Hub Interface Safety & Warnings • DO NOT install with power applied to device. From your ZigBee controller or hub interface, choose to delete or reset the • DO NOT expose the device to moisture. lighting device as instructed. The connected light blinks 3 times to indicate successful reset. Operation 1.Do wiring according to connection diagram correctly. 2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.

6. Factory Reset Manually 9. Learning to a Zigbee Green Power Remote Step 1: Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to start Learning mode (connected the “Prog.” key is not accessible. light flashes twice), 180 seconds timeout, repeat the operation. L OUTPUT L INPUT V- OUTPUT 12V/24V/36V INPUT 12V/24V/36V V- N N CV PSU V+ CV PSU G G V+ AC Power Step 3: Connected light AC Power 50/60Hz 50/60Hz Step 2: Connected light will blink 3 times will flash twice to indicate successful learning. Then to indicate successful reset. the remote can control the device. ZigBee RGBW Lighting Device ZigBee RGBW Lighting Device V+ V+ V+ V+ R- R- R- R- 1/R- 1/R- LED 2/G- LED 2/G- Prog. 3/B- Prog. 3/B- G- G- 4/W- G- G- Zigbee 4/W- B- B- B- B- Green Power W- W- W- W- Remote Step 2: Set the green power Note: Each device can learn to Note: 1) If the device is already at factory default setting, there is no indication when factory reset again . remote into Learning mode, 2) All configuration parameters will be reset after the device is reset or removed from the network. max. 20 zigbee green power remote. please refer to its manual. 7. Factory Reset through a Zigbee Remote (Touch Reset) Note: Make sure the device already added to a network, the remote added to the same one or not added to any 10. Delete Learning to a Zigbee Green Power Remote network. Step 1: Short press “Prog.” button 3 times (Or re-power on the device 3 times) to start delete Learning mode Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation. (connected light flashes slowly), 180 seconds timeout, repeat the operation. L OUTPUT INPUT 12V/24V/36V V- N CV PSU V+ L Step 4: There shall be G Step 3: Connected light will OUTPUT AC Power INPUT 12V/24V/36V V- N 50/60Hz G CV PSU V+ indication on the remote and flash 4 times to indicate AC Power 50/60Hz successful deleting. connected light flashes 3 times for successful reset. ZigBee RGBW Lighting Device V+ V+ 1/R- R- R- < 10cm LED 2/G- ZigBee RGBW Lighting Device Prog. 3/B- V+ V+ R- R- Zigbee 4/W- G- G- 1/R- B- B- Green Power W- W- LED 2/G- Prog. 3/B- Remote 4/W- G- G- B- B- Zigbee W- W- Remote Step 2: Set the paired green power remote into Learning mode, please refer to its manual. Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: Set the remote or touch panel into Touch Reset procedure to reset the device, please refer to corresponding remote or touch panel manual to learn how . 11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required) Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to enable the device to setup a 8. Find and Bind Mode zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat Step 1: Short press “Prog.” button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and the operation. Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation. L OUTPUT INPUT 12V/24V/36V V- N CV PSU V+ L G OUTPUT INPUT 12V/24V/36V V- AC Power N CV PSU V+ Zigbee 50/60Hz G AC Power Remote 50/60Hz ZigBee RGBW Lighting Device V+ V+ 1/R- R- R- ZigBee RGBW Lighting Device LED 2/G- V+ V+ Prog. 3/B- 1/R- R- R- 4/W- G- G- B- B- LED 2/G- W- W- Prog. < 10cm TouchLink 3/B- Zigbee 4/W- G- B- G- B- W- W- Remote Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it Step 2: Set another device or remote or touch panel into to find and bind initiator, please refer to corresponding remote or touch panel manual. ZigBee RGBW Lighting Device network pairing mode and pair to the network, refer to their 1/R- manuals. Step 3: There shall be indication on the remote or touch panel that it bind the device LED 2/G- Prog. 3/B- successfully and can control it then . 4/W-

Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals. Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals. Note: 1) Each added device can link and be controlled by max. 30 added remotes. FCC Warning Statement 2) Each added remote can link and control max. 30 added devices. This equipment has been tested and found to comply with the limits for a 12. ZigBee Clusters the device supports are as follows: Class B digital device, pursuant to part 15 of the FCC Rules. These limits are Input Clusters designed to provide reasonable protection against harmful interference in a • 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes • 0x0b05: Diagnostics residential installation. This equipment generates, uses and can radiate radio • 0x0006: On/off • 0x0008: Level Control • 0x0300: Color Control Output Clusters frequency energy and, if not installed and used in accordance with the • 0x0019: OTA instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular 13. OTA installation. If this equipment does cause harmful interference to radio or The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or television reception, which can be determined by turning the equipment off hub every 10 minutes automatically. and on, the user is encouraged to try to correct the interference by one or Wiring Diagram more of the following measures: • Reorient or relocate the receiving antenna. L • Increase the separation between the equipment and receiver. OUTPUT INPUT 12V/24V/36V V- N G CV PSU V+ • Connect the equipment into an outlet on a circuit different from that to which AC Power 50/60Hz the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. ZigBee RGBW Receiver V+ V+ R- R- Connect with RGBW LED Strip 1/R- This device complies with part 15 of the FCC Rules. Operation is subject to LED 2/G- Prog. 3/B- 4/W- G- G- B- W- B- W- the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, ZigBee RGBW Receiver including interference that may cause undesired operation. V+ V+ R- R- Connect with RGBW LED Strip 1/R- This equipment complies with FCC radiation exposure limits set forth for an LED 2/G- Prog. 3/B- G- G- uncontrolled environment. This equipment should be installed and operated 4/W- B- B- W- W- with minimum distance 20cm between the radiator and your body.


Document Created: 2019-05-16 15:28:34
Document Modified: 2019-05-16 15:28:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC