User manual

FCC ID: 2AHRH-FJ1000L

Users Manual

Download: PDF
FCCID_3211280

 FJ1000L_User Manual




  Positioning Universal Inc.




Positioning Universal, Inc. - Confidential & Proprietary


                                                                                    FJ1000L




1.1 Physical and Electrical Specifications
Dimensions: 103mm *53mm *18.65mm
Weight: 54.5 g (with optional battery)
Input Voltage: 8-30VDC
Power consumption:
        - Active mode: 200mA @12VDC
        - Sleep mode: <8mA @12VDC
Operating temperature: -30℃ to 80℃
Storage temperature: -40℃to 85℃

1.2 Input/Output
Digital Inputs: 1
Relay driver Outputs: 1
Function LEDs: 2
      GPS Status GREEN
      Cellular Status AMBER




1.3 Cellular Communication
Operation Mode:         FDD_LTE (Cat1)
Operation Band:         Lte_B4, Lte_B13
Modulation      :       Uplink: QPSK
                        Downlink: QPSK/16QAM



1.4 Harnesses
There are1 harnesses that may be used with the FJ1000L:
    1. 4 wire power and I/O harness


The picture above shows the 4 wire power and I/O harness. The wiring details are:
Power and I/O Harness 4 wires
    1. Blackor Red V+ is connected to Positive , +12VDC or +24VDC

                                                                                        2
                    Positioning Universal, Inc. - Confidential & Proprietary


                                                                                       FJ1000L


   2. GreyV- is connected to Negative or Ground
   3. GreenInput 0 is an input biased high, negative trigger.

   4.   BlueOutput 0 is an output, open collector, may be used for Starter Disable.




1.5 Event Codes
The table below relates the Event codes in the message to the reason the message was
generated:

Message
#           Message Type           Description
   0        Interval               Auto Report (auto report when moving)
   1        Vibration              Vibration alarm(report when GPS is OFF and vibration detected)
            Power
    2       Disconnect             Power cut alarm (report when external power is cut off)
    3       Power Connect          Power connected alarm (external power has been connected)
    4       Ignition ON            Hardwired or Virtual Ignition ON detected
    5       Ignition OFF           Hardwired or Virtual Ignition OFF detected
    6       Input 2 High           Input2 high alarm
    7       Input 2 Low            Input2 low alarm
    8       Stop                   Device has stopped moving
    9       Heartbeat              Heartbeat periodic report
   13       Input 1 High           Input1 high alarm
   14       Input 1 Low            Input 1 Low alarm
   19       Crash Alarm            Crash Detected
            Heading
   24       Change                 Heading change detected
   25       Tow Alert              Device is moving but being pulled
   35       Starter Disabled       An output has been set by SMS command
   36       Starter Enabled        An output has been cleared by SMS command
   41       Harsh Accel            Harsh acceleration has been detected
   42       Harsh Brake            Harsh Braking has been detected
   43       Swerve Left            A left swerve has been detected
   44       Swerve Right           A right swerve has been detected




                                                                                             3
                   Positioning Universal, Inc. - Confidential & Proprietary


                                                                                            FJ1000L




FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

-- Consult the dealer or an experienced radio/TV technician for help.



This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

RF Exposure Warning Statements:

The 20 cm distance between device and users must be maintained during the normal operations.




Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.




                                                                                                    4
                     Positioning Universal, Inc. - Confidential & Proprietary



Document Created: 2016-11-29 09:59:04
Document Modified: 2016-11-29 09:59:04

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC