Cover Letters_20171114_v1 - 13_11673430 COM2 FCC Modular Approval Request

FCC ID: 2AHES-COM2

Cover Letter(s)

Download: PDF
FCCID_3689646

Applicant/Grantee       BSH Home Appliance Corporation
FCC ID:                 2AHES-COMGEN2
                                      Section 15.212 Modular Transmitters
Request for Modular Approval                     Request for Limited Modular Approval
                        Requirements                               EUT Conditions                Comply (Y/N)
                                    Single Modular Approval Requirements
  1      The radio elements of the modular
         transmitter must have their own
         shielding. The physical crystal and                 Please Refer to EUT photos              YES
         tuning capacitors may be located
         external to the shielded radio elements.
  2      The modular transmitter must have
         buffered modulation/data inputs (if such
         inputs are provided) to ensure that the         EUT has buffered data inputs, and is        YES
         module will comply with Part 15                    integrated in chip BCM43907
         requirements under conditions of
         excessive data rates or over-modulation.
  3      The modular transmitter must have its                Power in chip BCM43907                 YES
         own power supply regulation.
  4      The modular transmitter must comply
         with the antenna and transmission
         system requirements of Sections 15.203,
         15.204(b) and 15.204(c). The antenna          The EUT has both integral antennas and        YES
         must either be permanently attached or         external antennas with unique coupler
         employ a “unique” antenna coupler (at
         all connections between the module and
         the antenna, including the cable). The
         “professional installation” provision of
         Section 15.203 is not applicable to
         modules but can apply to limited
         modular approvals under paragraph (b)
         of this section.
  5      The modular transmitter must be tested
         in a stand-alone configuration, i.e., the
         module must not be inside another
         device during testing for compliance             The EUT is tested in a stand-alone         YES
         with Part 15 requirements. Unless the            configuration as seen in test photos
         transmitter module will be battery
         powered, it must comply with the AC
         line conducted requirements found in
         Section 15.207. AC or DC power lines
         and data input/output lines connected to
         the module must not contain ferrites,
         unless they will be marketed with the
         module (see Section 15.27(a)). The
         length of these lines shall be the length
         typical of actual use or, if that length is
         unknown, at least 10 centimeters to
         insure that there is no coupling between
         the case of the module and supporting


    equipment. Any accessories, peripherals,
    or support equipment connected to the
    module during testing shall be
    unmodified and commercially available
    (see Section 15.31(i)).
6   The modular transmitter must be
    equipped with either a permanently
    affixed label or must be capable of
    electronically displaying its FCC                      EUT has permanent label affixed to         YES
    identification number.                                module PCB. See “Label Placement”
    (A) If using a permanently affixed label, the        photo. External label will also be affixed
    modular transmitter must be labeled with its own        to any host product to identify the
    FCC identification number, and, if the FCC
    identification number is not visible when the
                                                                   module’s presence.
    module is installed inside another device, then
    the outside of the device into which the module is
    installed must also display a label referring to
    the enclosed module. This exterior label can use
    wording such as the following: “Contains
    Transmitter Module
    FCC ID: XYZMODEL1” or “Contains FCC ID:
    XYZMODEL1.” Any similar wording
    that expresses the same meaning may be used.
    The Grantee may either provide such a label, an
    example of which must be included in the
    application for equipment
    authorization, or, must provide adequate
    instructions along with the module which explain
    this requirement. In the latter case, a copy of
    these instructions must be included in the
    application for equipment authorization.
    (B) If the modular transmitter uses an electronic
    display of the FCC identification number, the
    information must be readily accessible and
    visible on the modular transmitter or on the
    device in which it is installed. If the module is
    installed inside another device, then the outside
    of the device into which the module is installed
    must display a label referring to the enclosed
    module. This exterior label can use wording such
    as the following:
    “Contains FCC certified transmitter module(s).”
    Any similar wording that expresses the same
    meaning may be used. The user manual must
    include instructions on how to access the
    electronic display. A copy of these instructions
    must be included in the application for
    equipment authorization.
7   The modular transmitter must comply
    with any specific rules or operating
    requirements that
    ordinarily apply to a complete                            Please refer to User’s Manual           YES
    transmitter and the manufacturer must
    provide adequate instructions along with
    the module to explain any such
    requirements. A copy of these
    instructions must be included in the
    application for equipment authorization.


   8        The modular transmitter must comply           RF Exposure statement is included in
            with any applicable RF exposure                          User’s Manual                      YES
            requirements in its final configuration.
A limited modular approval may be granted for single or split modular transmitters that do not comply with
all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or
power supply regulation, if the manufacturer can demonstrate by alternative means in the application for
equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the
operating conditions in which the transmitter will be used. Limited modular approval also may be granted in
those instances where compliance with RF exposure rules is demonstrated only for particular product
configurations. The applicant for certification must state how control of the end product into which the module
will be installed will be maintained such that full compliance of the end product is always ensured.





Document Created: 2017-04-24 10:26:23
Document Modified: 2017-04-24 10:26:23

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC