User Manual

FCC ID: 2AHDSPS210-01

Users Manual

Download: PDF
FCCID_3100195

Installation Guide Overview & Operation Installation Home Automation Power Plug ❶ 1. No installation is required; just plug PS210P/PS210 into the existing wall PS210/PS210P ❷ power outlet. 2. Test the PS210/PS210P by plugging a home electrical device (e.g. a lamp) into PS210/PS210P and verify the following :  Press PS210/PS210P power plug’s toggle button to power on, and then check if the Green and Orange LED are off and the electrical device is powered on.  Press PS210/PS210P power plug’s toggle button again to power off, and then check if the Green and Orange LED are on and electrical device is powered off. ❶ Toggle Button Note:  Press to toggle the power plug’s power on/off manually The installation is now complete; you can now add your PS210/PS210P  Press and hold for 5 seconds to set the power plug to scan mode power plug to Controller, and control it using PS App.  Press and hold for 10 seconds to reset the power plug to factory The PS210/PS210P is a smart, controllable power plug for your home’s default setting electrical devices. PS210P includes the Energy Meter capability. Together with Controller, PS App (mobile Smartphone /Tablet), and all PS devices ❷ LED (switches, power plugs, dimmers, and sensors), the PS system provides you  Green and Orange – Flashing alternatively => In scan mode with the capability to control your home’s electrical devices remotely from  Green and Orange – steady on => Power is off and it is without ID anywhere in the world for home automation.  Green – steady on => Power is off and it is connected to the controller  Orange – steady on => Power is off and it lost connection to the controller Link PS210/PS210P to the Controller  Green and Orange – off => Power is on Download and install the latest PS App to your mobile device, and refer to the walk through instructions from PS App’s to add your PS210/P210P power plug to Controller. The main steps are: FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital  Use the PS App, set the Controller into the scan mode. device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  Press and hold PS210/PS210P power plug’s toggle button for 5 seconds reasonable protection against harmful interference in a residential installation. This to set it to scan mode. WARINGS AND CAUTIONS equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  The pairing process between the Controller and PS210/PS210P power  PS210/PS210P is intended to be used as an indoor home power plug ; it communications. However, there is no guarantee that interference will not occur in a plug will now take place. should never be used for medical and/or life support equipment particular installation. If this equipment does cause harmful interference to radio or  The PS App will show the new device, PS210/PS210P is added. television reception, which can be determined by turning the equipment off and on, the  Control PS210/PS210P using PS App via the Controller.  The operation and activation of PS210/PS210P can be controlled user is encouraged to try to correct the interference by one or more of the following remotely in a different place, or by automatic programmed control. measures: As the control may be intentional or unintentional due to programming, -- Reorient or relocate the receiving antenna. wrong button pressed, the result of the operation could be undesirable, -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the unexpected, or even hazardous. Please exercise caution. receiver is connected.  If you are unsure or uncomfortable about performing the installation, -- Consult the dealer or an experienced radio/TV technician for help. please consult a qualified electrician. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Document Created: 2016-06-20 15:37:01
Document Modified: 2016-06-20 15:37:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC