Test report 1

FCC ID: 2AH4HATD300S

Test Report

Download: PDF

FCCID_3902142

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

1.3 Test Methodology and Considerations

The EUT is capable of being powered from a coin cell battery, commercially available wall-wart
power supply, and the USB communication cable from a laptop. All modes of operation, including
all data rates, were evaluated and the data presented in this report represents the worst case
where applicable. The module was tested in a standalone condition on an evaluation board.

For radiated emissions, the EUT was evaluated in three orthogonal orientations. The worst-case
orientation was Z-orientation. The EUT was evaluated with the coin cell battery, wall-wart power
supply, and over USB from a representative laptop computer. The worst-case power mode was
the wall-wart power supply. See test setup photos for more information. The EUT was evaluated
with the highest gain antenna of each type. See the Theory of Operations for more information.

For AC power line conducted emissions, the EUT was evaluated with a commercially available
wall-wart power supply and over USB from a laptop computer. The worst-case power mode was
over USB from a laptop computer and was evaluated with the highest gain antenna of each type.

For RF Conducted Emissions, the EUT was evaluated using the external U.FL antenna connector
with suitable attenuation. The coupling cable and external attenuation were considered for all RF
conducted measurements.

Power setting during test: 0

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 4

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

2 TEST FACILITIES

2.1 Location

The radiated and conducted emissions test sites are located at the following address:

TÜV SÜD America, Inc.
5015 B.U. Bowman Drive
Buford, GA 30518
Phone: (770) 831-8048
Fax: (770) 831-8598

2.2 Laboratory Accreditations/Recognitions/Certifications

TÜV SÜD America, Inc. is accredited to ISO/IEC 17025 by the ANSI-ASQ National Accreditation
Board/ANAB accreditation program, and has been issued certificate number AT-2021 in
recognition of this accreditation. Unless otherwise specified, all tests methods described within
this report are covered under the ISO/IEC 17025 scope of accreditation.

The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions
Site have been fully described, submitted to, and accepted by the FCC, ISED Canada and the
Japanese Voluntary Control Council for Interference by information technology equipment.

FCC Registration Number: 391271
ISED Canada Lab Code: IC 4175A
VCCI Member Number: 1831
• VCCI OATS Registration Number R-1526
• VCCI Conducted Emissions Site Registration Number: C-1608

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 5

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

2.3 Radiated Emissions Test Site Description

2.3.1 Semi-Anechoic Chamber Test Site

The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The
chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is
101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel
panels and installed directly on the inner walls of the chamber.

The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The
chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is
bound to the ground plane using 3/4" stainless steel braided cable.

The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely
operated from inside the control room located 25’ from the range. The turntable is electrically
bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table.
The steel fingers make constant contact with the ground plane during operation.

Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary.
The pit is equipped with 1 - 4” PVC chases from the turntable to the pit that allow for cabling to
the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can
be supplied to the EUT from the pit.

A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3-1 below:

3 Meters

5 Feet
Diameter

20 Feet

30 Feet
Figure 2.3-1: Semi-Anechoic Chamber Test Site

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 6

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

2.3.2 Open Area Tests Site (OATS)

The open area test site consists of a 40’ x 66’ concrete pad covered with a perforated electro-
plated galvanized sheet metal. The perforations in the sheet metal are 1/8” holes that are
staggered every 3/16”. The individual sheets are placed to overlap each other by 1/4” and are
riveted together to provide a continuous seam. Rivets are spaced every 3” in a 3 x 20 meter
perimeter around the antenna mast and EUT area. Rivets in the remaining area are spaced as
necessary to properly secure the ground plane and maintain the electrical continuity.

The entire ground plane extends 12’ beyond the turntable edge and 16’ beyond the antenna mast
when set to a 10 meter measurement distance. The ground plane is grounded via 4 - 8’ copper
ground rods, each installed at a corner of the ground plane and bound to the ground plane using
3/4" stainless steel braided cable.

The turntable is an all aluminum 10’ flush mounted table installed in an all aluminum frame. The
table is remotely operated from inside the control room located 40’ from the range. The turntable
is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of
the turn table. The steel fingers make constant contact with the ground plane during operation.

Adjacent to the turntable is a 7’ x 7’ square and 4’ deep concrete pit used for support equipment if
necessary. The pit is equipped with 5 - 4” PVC chases from the pit to the control room that allow
for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit
so cables can be supplied to the EUT from the pit. The pit is covered with 2 sheets of 1/4"
diamond style re-enforced steel sheets. The sheets are painted to match the perforated steel
ground plane; however the underside edges have been masked off to maintain the electrical
continuity of the ground plane. All reflecting objects are located outside of the ellipse defined in
ANSI C63.10.

A diagram of the Open Area Test Site is shown in Figure 2.3-2 below:

10Meter

3 Meters

40Feet

7x7x4
Pit

66 Feet

Figure 2.3-2: Open Area Test Site

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 7

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

4 LIST OF TEST EQUIPMENT

The calibration interval of test equipment is annually or the manufacturer’s recommendations.
Where the calibration interval deviates from the annual cycle based on the instrument
manufacturer’s recommendations, it shall be stated below.

Table 4-1: Test Equipment
Calibration
AssetID Manufacturer Model # Equipment Type Serial # Last Calibration Date Due Date
30 Spectrum Technologies DRH-0118 Antennas 970102 4/30/2015 4/30/2017
40 EMCO 3104 Antennas 3211 6/8/2016 6/8/2018
73 Agilent 8447D Amplifiers 2727A05624 7/21/2016 7/21/2017
Chamber EMI
167 ACS Cable Set Cable Set 167 9/30/2016 9/30/2017
267 Agilent N1911A Meters MY45100129 8/24/2015 8/24/2017
268 Agilent N1921A Sensors MY45240184 8/13/2015 8/13/2017
324 ACS Belden Cables 8214 3/21/2017 3/21/2018
334 Rohde&Schwarz 3160-09 Antennas 49404 11/4/2010 NCR
335 Suhner SF-102A Cables 882/2A 7/12/2016 7/12/2017
338 Hewlett Packard 8449B Amplifiers 3008A01111 8/21/2015 8/21/2017
340 Aeroflex/Weinschel AS-20 Attenuators 7136 7/12/2016 7/12/2017
345 Suhner Sucoflex 102A Cables 1077/2A 7/12/2016 7/12/2017
412 Electro Metrics LPA-25 Antennas 1241 8/8/2016 8/8/2018
SMS-200AW-72.0-
422 Florida RF SMR Cables 805 10/27/2016 10/27/2017
432 Microwave Circuits H3G020G4 Filters 264066 5/13/2016 5/13/2017
SMRE-200W-12.0-
616 Florida RF Cables SMRE Cables N/A 9/2/2016 9/2/2017
622 Rohde & Schwarz FSV40 Analyzers 101338 7/15/2016 7/15/2018
SMS-290AW-
676 Florida RF Labs 480.0-SMS Cables MFR2Y194 11/4/2016 11/4/2017
812 PMM 9030 Receiver 121WW30401 2/6/2017 2/6/2018
3010 Rohde & Schwarz ENV216 LISN 3010 7/11/2016 7/11/2017
RE135 Rohde & Schwarz FSP30 Spectrum Analyzers 835618/031 10/31/2016 10/31/2017
NCR = No Calibration Required
NOTE: All test equipment was used only during active calibration cycles.

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 9

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

5 SUPPORT EQUIPMENT

Table 5-1: Support Equipment – Radiated Emissions
Item Equipment Type Manufacturer Model/Part Serial Number
Number
Wall Wart Power Cnet Enterprise
1 AD1605C N/A
Supply Corp.

Table 5-2: Cable Description – Radiated Emissions
Cable Cable Type Length Shield Termination
10 cm (Lcom Antenna)
A RF Cable 45 cm (CUSHCRAFT Yes EUT to Antenna
Antenna)
EUT to Wall Wart
B DC Power Cable 250 cm No
Power Supply

Table 5-3: Support Equipment – Power Line Conducted Emissions
Item Equipment Type Manufacturer Model/Part Serial Number
Number
1 Laptop Dell Latitude E5450 N/A
2 Laptop Power Brick Dell LA65NM130 N/A
3 Headphones Micro Innovations N/A N/A

Table 5-4: Cable Description – Power Line Conducted Emissions
Cable Cable Type Length Shield Termination
10 cm (Lcom Antenna)
A RF Cable 45 cm (CUSHCRAFT Yes EUT to Antenna
Antenna)
B USB Cable 200 cm No EUT to Laptop
C DC Power Cable 200 cm No Laptop to Power Brick
Power Brick to AC
D AC Power Cable 150 cm No
Mains
Laptop to
E Stereo Cable 200 cm No
Headphones

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 10

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM

A
EUT

B

1

AC Mains

NOTE: the external antenna and Cable A were not connected during the internal antenna evaluation
Figure 6-1: Test Setup Block Diagram – Radiated Emissions

A B E
EUT 1 3

C

2

D

AC Mains

NOTE: the external antenna and Cable A were not connected during the internal antenna evaluation
Figure 6-2: Test Setup Block Diagram – Power Line Conducted Emissions

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 11

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

Table 7.2.2-1: Conducted EMI Results Line 1 – Internal Antenna

Corrected Reading Limit Margin
Frequency Correction
(MHz) (dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
(dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)
0.15 43.18 23.86 66 56 -22.82 -32.14 9.59
0.158 44.91 29.11 65.57 55.57 -20.66 -26.46 9.58
0.174 43.16 22.82 64.77 54.77 -21.61 -31.95 9.58
0.19 41.21 24.21 64.04 54.04 -22.83 -29.83 9.58
0.226 40.27 22.54 62.6 52.6 -22.33 -30.06 9.58
0.414 39.34 22.41 57.57 47.57 -18.23 -25.16 9.59
0.454 41.74 30.75 56.8 46.8 -15.06 -16.05 9.59
0.65 36.13 22.43 56 46 -19.87 -23.57 9.59
2.37 35.12 22.86 56 46 -20.88 -23.14 9.71
15.714 32.97 23.39 60 50 -27.03 -26.61 9.82

Table 7.2.2-2: Conducted EMI Results Line 2 – Internal Antenna

Corrected Reading Limit Margin
Frequency Correction
(MHz) (dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
(dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)
0.15 54.27 32.23 66 56 -11.73 -23.77 9.59
0.158 54.53 32.1 65.57 55.57 -11.04 -23.47 9.58
0.174 53.31 22.7 64.77 54.77 -11.46 -32.07 9.58
0.198 48.76 24.58 63.69 53.69 -14.93 -29.11 9.58
0.234 46.81 22.36 62.31 52.31 -15.5 -29.95 9.58
0.25 42.03 22.3 61.76 51.76 -19.73 -29.46 9.58
0.378 43.95 22.27 58.32 48.32 -14.37 -26.05 9.59
0.402 44.6 22.27 57.81 47.81 -13.21 -25.54 9.59
0.458 46.72 27.13 56.73 46.73 -10.01 -19.6 9.59
0.486 44.37 22.35 56.24 46.24 -11.87 -23.89 9.59

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 13

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

Table 7.2.2-3: Conducted EMI Results Line 1 – Patch Antenna

Corrected Reading Limit Margin
Frequency Correction
(MHz) (dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
(dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)
0.15 54.78 36.91 66 56 -11.22 -19.09 9.59
0.17 46.38 22.7 64.96 54.96 -18.58 -32.26 9.58
0.182 50.41 25.44 64.39 54.39 -13.98 -28.95 9.58
0.19 49.92 29.32 64.04 54.04 -14.12 -24.72 9.58
0.23 48.22 22.4 62.45 52.45 -14.23 -30.05 9.58
0.242 41.82 22.35 62.03 52.03 -20.21 -29.68 9.58
0.378 40.84 24.04 58.32 48.32 -17.48 -24.28 9.59
0.438 41.03 24.17 57.1 47.1 -16.07 -22.93 9.59
0.47 42.8 29.47 56.51 46.51 -13.71 -17.04 9.59
0.486 42.47 27.25 56.24 46.24 -13.77 -18.99 9.59

Table 7.2.2-4: Conducted EMI Results Line 2 – Patch Antenna

Corrected Reading Limit Margin
Frequency Correction
(MHz) (dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
(dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)
0.15 52.78 29.98 66 56 -13.22 -26.02 9.59
0.194 48.46 24.45 63.86 53.86 -15.4 -29.41 9.58
0.23 45.96 22.4 62.45 52.45 -16.49 -30.05 9.58
0.29 41.88 22.33 60.52 50.52 -18.64 -28.19 9.59
0.35 39.04 22.32 58.96 48.96 -19.92 -26.64 9.59
0.394 43.48 24.12 57.98 47.98 -14.5 -23.86 9.59
0.406 45.79 27.63 57.73 47.73 -11.94 -20.1 9.59
0.434 45.29 25.5 57.18 47.18 -11.89 -21.68 9.59
0.45 43.75 29.08 56.88 46.88 -13.13 -17.8 9.59
0.478 43.73 25.1 56.37 46.37 -12.64 -21.27 9.59

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 14

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

Table 7.2.2-5: Conducted EMI Results Line 1 – Dipole Antenna

Corrected Reading Limit Margin
Frequency Correction
(MHz) (dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
(dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)
0.15 55.39 38.46 66 56 -10.61 -17.54 9.59
0.154 49.69 28.91 65.78 55.78 -16.09 -26.87 9.58
0.162 47.34 27.89 65.36 55.36 -18.02 -27.47 9.58
0.198 48.73 28.42 63.69 53.69 -14.96 -25.27 9.58
0.23 46.76 22.98 62.45 52.45 -15.69 -29.47 9.58
0.298 41.45 22.36 60.3 50.3 -18.85 -27.94 9.58
0.374 42.75 23.39 58.41 48.41 -15.66 -25.02 9.59
0.39 44.63 27.01 58.06 48.06 -13.43 -21.05 9.59
0.422 44.15 26.26 57.41 47.41 -13.26 -21.15 9.59
0.442 43.39 24.02 57.02 47.02 -13.63 -23 9.59

Table 7.2.2-6: Conducted EMI Results Line 2 – Dipole Antenna

Corrected Reading Limit Margin
Frequency Correction
(MHz) (dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
(dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)
0.15 53.82 32.85 66 56 -12.18 -23.15 9.59
0.19 48.74 23.17 64.04 54.04 -15.3 -30.87 9.58
0.222 45.21 22.43 62.74 52.74 -17.53 -30.31 9.58
0.39 44.59 23.84 58.06 48.06 -13.47 -24.22 9.59
0.406 45.09 27.44 57.73 47.73 -12.64 -20.29 9.59
0.418 44.82 26.23 57.49 47.49 -12.67 -21.26 9.59
0.438 42.96 26.58 57.1 47.1 -14.14 -20.52 9.59
0.454 45.58 29.2 56.8 46.8 -11.22 -17.6 9.59
0.474 44.79 25.75 56.44 46.44 -11.65 -20.69 9.59
0.49 43.56 22.36 56.17 46.17 -12.61 -23.81 9.59

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 15

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

Table 7.5.2.3-2: Radiated Spurious Emissions Tabulated Data – Patch Antenna
Level Antenna Correction Corrected Level Limit Margin
Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB)
(MHz)
pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg
Lowest Channel
2390 38.55 37.34 H -5.40 33.15 -1.53 74.0 54.0 40.8 55.5
2390 40.80 39.27 V -5.40 35.40 0.40 74.0 54.0 38.6 53.6
4804 51.16 49.93 H 1.80 52.96 18.26 74.0 54.0 21.0 35.7
4804 48.45 47.37 V 1.80 50.25 15.70 74.0 54.0 23.7 38.3
Middle Channel
4880 48.89 47.26 H 2.04 50.93 15.83 74.0 54.0 23.1 38.2
4880 45.76 44.61 V 2.04 47.80 13.18 74.0 54.0 26.2 40.8
7320 44.26 41.81 H 7.74 52.00 16.08 74.0 54.0 22.0 37.9
Highest Channel
2483.5 54.91 54.00 H -4.94 49.97 15.58 74.0 54.0 24.0 38.4
2483.5 66.32 65.19 V -4.94 61.38 26.77 74.0 54.0 12.6 27.2
4960 50.42 49.25 H 2.29 52.71 18.07 74.0 54.0 21.3 35.9
4960 47.30 46.18 V 2.29 49.59 15.00 74.0 54.0 24.4 39.0

Table 7.5.2.2-3: Radiated Spurious Emissions Tabulated Data – Dipole Antenna
Level Antenna Correction Corrected Level Limit Margin
Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB)
(MHz)
pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg
Lowest Channel
2390 38.69 37.11 H -5.40 33.29 -1.76 74.0 54.0 40.7 55.8
2390 38.39 37.20 V -5.40 32.99 -1.67 74.0 54.0 41.0 55.7
4804 46.00 45.04 H 1.80 47.80 13.37 74.0 54.0 26.2 40.6
4804 52.68 51.96 V 1.80 54.48 20.29 74.0 54.0 19.5 33.7
Middle Channel
4880 46.75 45.70 H 2.04 48.79 14.27 74.0 54.0 25.2 39.7
4880 55.05 54.16 V 2.04 57.09 22.73 74.0 54.0 16.9 31.3
Highest Channel
2483.5 54.55 53.10 H -4.94 49.61 14.68 74.0 54.0 24.4 39.3
2483.5 60.43 58.76 V -4.94 55.49 20.34 74.0 54.0 18.5 33.7
4960 44.79 43.35 H 2.29 47.08 12.17 74.0 54.0 26.9 41.8
4960 51.88 50.79 V 2.29 54.17 19.61 74.0 54.0 19.8 34.4
7440 43.20 41.95 H 7.84 51.04 16.31 74.0 54.0 23.0 37.7

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 22

Model(s): MBN52832 FCC ID: HSW2832 IC: 4492A-2832

7.5.2.4 Sample Calculation:
RC = RU + CFT

Where:
CFT = Total Correction Factor (AF+CA+AG)-DC (Average Measurements Only)
RU = Uncorrected Reading
RC = Corrected Level
AF = Antenna Factor
CA = Cable Attenuation
AG = Amplifier Gain
DC = Duty Cycle Correction Factor

Example Calculation: Peak – Internal Antenna

Corrected Level: 36.45 - 5.40 = 31.05dBuV/m
Margin: 74dBuV/m – 31.05dBuV/m = 42.9dB

Example Calculation: Average – Internal Antenna

Corrected Level: 35.86 - 5.40 - 33.47 = -3.01dBuV
Margin: 54dBuV – -3.01dBuV = 57.0dB

Report No: AT72126480-1C1 TÜV SÜD America, Inc. Page 23

Document Created: 2017-08-25 09:40:26
Document Modified: 2017-08-25 09:40:26

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC