test report SAR 4

FCC ID: 2AH25T8A01

Test Report

Download: PDF
FCCID_4407491

ECIT TTL " $ p_e—a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinatt.com hittp:/Awwwwchinattl.en DASY5 Validation Report for Body TSL Date: 11.01.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN: 1031 Communication System: UID 0, CW; Frequency: 2600 MHz; Duty Cycle: 1: 1 Medium parametersused: {= 2600 MHz; a = 2.206 S/m; s, = 52.65; p = 1000 kg/m3 Phantom section: Right Section DASYS Configuration: * Probe: EX3DV4 — SN7514; ConvF(7.06, 7.06, 7.06) @ 2600 MHz; Calibrated: 8$/27/2018 * Sensor—Surface: 1.4mm (Mechanical Surface Detection) «+ Electronics: DAE4 Sn1555; Calibrated: 8/20/2018 *« Phantom: MFP_V5.1C ; Type: QD 000 PS1CA; Serial: 1062 * Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=3mm, dz=5mm Reference Value = 96.99 V/m; Power Drift=—0.01 dB Peak SAR (extrapolated)= 30.0 W/kg SAR(I g) = 13.7 W/kg; SAR(10 g) =6.06 W/kg Maximum value of SAR (measured) =23.6 W/kg 0 dB =23.6 W/kg = 13.73 dBW/kg Certificate No: Z18—60431 Page 7 of 8

Report No.: I19D00082-SAR01 East China Institute of Telecommunications Page Number : 195 of 212 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date: August 13, 2019

ECIT ® n Collaboration with ‘w",, EWA TTL e_a Y _ linky ieeincstCS WR Chsuoe E—mail: cttl@chinatt.com hitps/wwwchinattl.en hululs Client ECIT Certificate No: Z18—60042 Object D5GHzV2 — SN: 1172 Calibration Procedure(s) FF—211—003—01 Calibration Procedures for dipole validation kits Calibration date: March 30, 2018 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22«3)‘C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 102083 O1—Nov—17 (CTTL, No.J17X08756) Oct—18 Power sensor NRP—Z91 100542 01—Nov—17 (CTTL, No.J17X08756) Oct—18 ReferenceProbe EX3DV4 SN 7464 12—Sep—17(SPEAG,No.EX3—7464_Sep17) Sep—18 DAE4 SN 1525 02—Oct—17(SPEAG,No.DAE4—1525_Oct17) Oct—18 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—18 (CTTL, No.J18X00560) Jan—19 NetworkAnalyzerES071C MY46110673 24—Jan—18 (CTTL, No.J18X00561) Jan—19 Name Function Signature Celibrated by: Zhao Jing SAR Test Engineer ‘ Reviewed by: Lin Hao SAR Test Engineer M Appreved by: Qi Dianyuan SAR Project Leader t $y‘ c Issued: April 2, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z18—60042 Page 1 of 16 ncc. ruu 6+ vuurruuuy e run Tuy 2+ vev ruuy s knepes ces e e es

ECIT _ 7T7 a s e Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—25 12 Fax: +86—10—62304633—2504 E—mail: ctl@chinattl.com hitp=//wwwchinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. «_ Antenna Parameters with TSL: The dipole is mounted with the spacer to positionits feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. «_ Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned underthe liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. «_ Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. & SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z18—60042 Page 2 of 16 LEL. +900 61 uuurruuuy r rva. ruy 6+ vuvcruuy s o

ECIT | LC Inlauist ® in Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—25 12 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps/wwwchinattl.en Measurement Conditions DASY system configuration, as far as notgiven on page 1. DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4 mm, dz = 1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz + 1 MHz 5300 MHz + 1 MHz Frequency 5500 MHz + 1 MHz 5600 MHz + 1 MHz 5800 MHz + 1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 £0.2) °C 36.2 16 % 4.70 mholm £ 6 % Head TSL temperature change during test <1.0 °C — — SAR result with Head TSL at 5200 MHz SAR averaged over 1 Cm" (1g) of Head TSL Condition SAR measured 100 mW input power 7.48 mW /g SAR for nominal Head TSL parameters normalized to 1W 74.9 mW 1g £ 24.4 % (k=2) SAR averaged over 10 cm° (10 g) of Head TSL Condition SAR measured 100 mW input power 2.14 mW /g SAR for nominal Head TSL parameters normalized to 1W 21.4 mW 1g + 24.2 % (k=2) Certificate No: Z18—60042 Page 3 of 16 nc ruu 64 vuuruwuv rrim cruv ea vuu rvuy s

ECIT ® in Collaboration with CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps//wwwchinattl.en Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0£0.2) °C 36.7 26 % 4.77 mho/m + 6 % Head TSL temperature change during test <1.0 °C «—— «.. SAR result with Head TSL at 5300 MHz SAR averaged over 1 Cm" (1 g) of Head TSL Condition SAR measured 100 mW input power 7.54 mW /g SAR for nominal Head TSL parameters normalized to 1W 75.8 mW 1g # 24.4 % (k=2) SAR averaged over 10 cm° (10 g) of Head TSL Condition SAR measured 100 mW input power 2.11 mW/g SAR for nominal Head TSL parameters normalized to 1W 21.2 mW i & 24.2 % (k=2) Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 35.8 £ 6 % 4.97 mho/m + 6 % Head TSL temperature change during test <1.0 °C ~—— —— SAR result with Head TSL at 5500 MHz SAR averaged over 1 Cm° (1 g) of Head TSL Condition SAR measured 100 mW input power 7.99 mW /g SAR for nominal Head TSL parameters normalized to 1W 80.0 mW 1g + 24.4 % (k=2) SAR averaged over 10 cm" (10 g) of Head TSL Condition SAR measured 100 mW input power 2.26 mW /g SAR for nominal Head TSL parameters normalized to 1W 22.6 mW 1g £ 24.2 % (k=2) Certificate No: Z18—60042 Page 4 of 16 ncclruv ea vuuruuuy r im cruv er vuu uy s

ECIT _ ® in Collaboration with CALIBRATION LABORATORY Add: No.31 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://wwwchinattl.on Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.8 16 % 5.10 mho/m + 6 % Head TSL temperature change during test <1.0 °C — —— SAR result with Head TSL at 5600 MHz SAR averaged over 1 Cm" (1 g) of Head TSL Condition SAR measured 100 mW input power 7.91 mW/g SAR for nominal Head TSL parameters normalized to 1W 79.3 mW 1g # 24.4 % (k=2) SAR averaged over 10 Cm" (10 g) of Head TSL Condition SAR measured 100 mW input power 2.21 mW/g SAR for nominal Head TSL parameters normalized to 1W 22.2 mW 1 # 24.2 % (k=2) Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.3 5.27 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.6 £ 6 % 5.28 mho/m + 6 % Head TSL temperature change during test <1.0 °C —— _— SAR result with Head TSL at 5800 MHz SAR averaged over 1 Cm" (1 g) of Head TSL Condition SAR measured 100 mW input power 7.36 mW /g SAR for nominal Head TSL parameters normalized to 1W 73.7 mW 1g 2 24.4 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL Condition SAR measured 100 mW input power 2.06 mW /g SAR for nominal Head TSL parameters normalized to 1W 20.7 mW 1g # 24.2 % (k=2) Certificate No: Z18—60042 Page 5 of 16 ncc. ruu 6+ vuurruuuy e run Tuy 2+ vev ruuy s

ECIT ® in Collaboration with CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps//www.chinattl.en Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (220£0.2) °C 48.9 26 % 5.29 mhoim +6 % Body TSL temperature change during test <1.0 °C weee «s SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm° (1 g) of Body TSL Condition SAR measured 100 mW input power 7.09 mW /g SAR for nominal Body TSL parameters normalized to 1W 70.9 mW 1g £ 24.4 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL Condition SAR measured 100 mW input power 1.98 mW /g SAR for nominal Body TSL parameters normalized to 1W 19.8 mW ig # 24.2 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 £0.2) °C 48.7 16 % 5.40 mho/m + 6 % Body TSL temperature change during test <1.0 °C —— SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm° (1 g) of Body TSL Condition SAR measured 100 mW input power 7.12 mW /g SAR for nominal Body TSL parameters normalized to 1W 71.1 mW ig 4 24.4 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL Condition SAR measured 100 mW input power 1.98 mW/g SAR for nominal Body TSL parameters normalized to 1W 19.8 mW 1g £ 24.2 % (k=2) Certificate No: Z18—60042 Page 6 of 16 ncclruv ea vuuruuuy r im cruv er vuu uy s

ECIT 1 Inlaiaia® ® in Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com https//wwwchinattl Len Bo« dy TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 20.2) °C 48.2 1 6 % 5.67 mho/m + 6 % Body TSL temperature change during test <1.0 °C wons ~—— SAl R result with Body TSL at 5500 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.72 mW !g SAR for nominal Body TSL parameters normalized to 1W T7A mW ig + 24.4 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL Condition SAR measured 100 mW input power 2.14 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.4 mW ig # 24.2 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mholm Measured Body TSL parameters (22.020.2) °C 48.1 26 % 5.81 mho/m +6 % Body TSL temperature change during test <1.0 °C ——— —— SAR result with Body TSL at 5600 MHz SAR averaged over 1 Cm° (1 g) of Body TSL Condition SAR measured 100 mW input power 7.52 mW /g SAR for nominal Body TSL parameters normalized to 1W 75.1 mW 1g £ 24.4 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL Condition SAR measured 100 mW input power 2.10 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.0 mW 1g + 24.2 % (k=2) Certificate No: Z18—60042 Page 7 of 16 ncc. ruu ea vuuruewv r rin ruv 2+ vev rvwes song———

ECIT ZTZL 1288 ® In Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com http=//wwwchinattl.en Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 20.2) °C 47.7 26 % 6.09 mho/m + 6 % Body TSL temperature change during test <1.0 °C —— —— SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm° (1g) of Body TSL Condition SAR measured 100 mW input power 7.27 mW1g SAR for nominal Body TSL parameters normalized to 1W 72.6 mW Ig # 24.4 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL Condition SAR measured 100 mW input power 2.02 mW /g SAR for nominal Body TSL parameters normalized to 1W 20.2 mW Ig + 24.2 % (k=2) Certificate No: Z18—60042 Page 8 of 16

ECIT i 7TTL a $ p_e Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: ettl@chinatl.com hitp=//wwwchinattl.en Appendix (Additional assessments outside the scope of CNAS L0570) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 53.10— 8. 1610 Return Loss —21.508B Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 49.80 — 5.65)0 Return Loss —25.00B Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 53.20 — 6.65)0 Return Loss —22.90B Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 58.60 — 2.98]0 Return Loss ~21.60B Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 55.00 — 3.20(0 Return Loss —24.908 Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 50.50 — 9.3910 Return Loss ~20.6dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 51.00.—4.11j0 Return Loss —27.60B Certificate No: Z18—60042 Page 9 of 16 pEL. +99 61 uuuruwuv e rva Tev 2+ vuv uy s ncope n ce en n n en

ECIT | Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Faxc: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp://wwwchinattl.en Antenna Parameters with Body TSLat 5500 MHz Impedance, transformed to feed point 50.30 — 4.72j0 Return Loss —26.50B Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 57.00 — 5.31j0 Return Loss —21.70B Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 58.80 — 0.730 Return Loss —21.908 General Antenna Parameters and Design Electrical Delay (one direction) 1.071 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to thedipole arms in orderto improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by spEAG Certificate No: Z18—60042 Page 10 of 16 LEL. +900 £1 uuurruuuy i i. Tuv 2r vuvcruuy s nepsn e >

ECIT c TL ts ® in Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps//wwwchinattl.en DASY5 Validation Report for Head TSL Date: 03.30.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1172 Communication System: CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz, Medium parameters used: f = 5200 MHz; 0 = 4.704 mho/m; er = 36.22; p = 1000 kg/m3, Medium parameters used: f = 5300 MHz; a = 4.77 mho/m; er = 36.74; p = 1000 kg/m3, Medium parameters used: f= 5500 MHz; a = 4.966 mho/m; er = 35.76; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 5.104 mho/m; &r = 35.78; p = 1000 kg/m3, Medium parameters used: f = 5800 MHz; a = 5.281 mho/m; &r = 35.62; p = 1000 kg/im3, Phantom section: Left Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASYS5 Configuration: * Probe: EX3DV4 — SN7464; ConvF(5.82, 5.82, 5.82); Calibrated: 9/12/2017, ConvF(5.53,5.53,5.53); Calibrated: 9/12/2017,ConvF(5.21,5.21,5.21); Calibrated: 9/12/2017, ConvF(4.98,4.98,4.98); Calibrated: 9/12/2017, ConvF(5.11,5.11,5.11); Calibrated: 9/12/2017, * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn1525; Calibrated: 2017—10—02 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/3 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration /Pin=100mW, d=10mm, f=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 60.30 V/im; Power Drift = —0.06 dB Peak SAR (extrapolated) = 32.5 Wikg SAR(1 g) =7.48 Wikg; SAR(10 g) = 2.14 Wikg Maximum value of SAR (measured) = 18.7 Wkg Dipole Calibration /Pin=100mW, d=10mm, f=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.18 V/im; Power Drift = —0.08 dB Peak SAR (extrapolated) = 34.1 Wikg SAR(1 g) =7.54 W/kg; SAR(10 g) =2.11 Wikg Maximum value of SAR (measured) = 18.7 W/kg Certificate No: Z18—60042 Page 11 of 16 EL. +00 61 uuuruwuv e i Tov er vuw ruuy s cope>

ECIT | L infi ® in Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—25 12 Faxc: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp=//wwwchinattlen Dipole Calibration /Pin=100mW, d=10mm, f=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.80 V/im; Power Drift = 0.03 dB Peak SAR (extrapolated) = 35.7 Wikg SAR(1 g) =7.99 Wikg; SAR(10 g) = 2.26 Wikg Maximum value of SAR (measured) = 19.3 Wkg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 61.90 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 37.2 W/kg SAR(1 g) = 7.91 W/kg; SAR(10 g) = 2.21 Wkg Maximum value of SAR (measured) = 19.7 Wikg Dipole Calibration /Pin=100mW, d=10mm, f=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 60.37 V/im; Power Drift = 0.02 dB Peak SAR (extrapolated) = 37.1 Wikg SAR(1 g) =7.36 Wikg; SAR(10 g) = 2.06 Wikg Maximum value of SAR (measured) = 19.0 W/kg —8.83 17.67 —26.50 435.34 C: ~44.17 0 dB = 19.0 Wikg = 12.79 dBWikg Certificate No: Z18—60042 Page 12 of 16 pEL. +99 61 uuuruwuv e rva Tev 2+ vuv uy s ncope n ce en n n en

ECIT TTL _a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Faxc: +86—10—62304633—2504 E—mail: cttl@chinattl.com https//wwwchinattl.en Impedance Measurement Plot for Head TSL Tri sif Log nag 10.00087 nef 0. 000de [Fi] 5999. rst—3.2000000 onz <21.437 ds s0.00 2 52000000 anz 241955 d —90 3 $.5000000 nz —22.983 do 4 $.6000000 anz —22.566 ce 30.00 5. 5.8000000 anz ~24.898 do 20.00 10.00 0. 000 —20.00 ~20.00 —30.00 ~+0.00 ~s0.00 x x is x si1 smith (ReJX) scale 1.000U [FL vel] >A $2000000 one s3.144 o —8.1660 n 3.7490—p 2 $.3000000 onz 49.789 o ~s.6a5e o 5. grmh 3 $.5000000 ane ss.is1 o —6.6542 o 4 516000000 onz 581565 a —2.9780 o 5. 5.8000000 ane 55.049 n —3.2044 o Certificate No: Z18—60042 Page 13 of 16 rneprveee rervarvrse e mriune e rerg ue reg ue

ECIT 3 7TTL a s p_e Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http=//wwwchinattl.en DASY5 Validation Report for Body TSL Date: 03.20.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1172 Communication System: CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz, Medium parameters used: f = 5200 MHz; 0 = 5.285 mho/m; er = 48.89; p = 1000 kg/m3, Medium parameters used: f = 5300 MHz; 0 = 5.398 mho/m; &r = 48.67; p = 1000 kg/im3, Medium parameters used: f = 5500 MHz; a = 5.674 mho/m; er = 48.24; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 5.813 mho/m; er = 48.05; p = 1000 kg/m3, Medium parameters used: f = 5800 MHz; a = 6.093 mho/m; &r = 47.65; p = 1000 kg/m3, Phantom section: Center Section MeasurementStandard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN7464; ConvF(5.39, 5.39, 5.39); Calibrated: 9/12/2017, ConvF(5.19, 5.19, 5.19); Calibrated: 9/12/2017,ConvF(4.61,4.61,4.61); Calibrated: 9/12/2017, ConvF(4.5,4.5,4.5); Calibrated: 9/12/2017, ConvF(4.67,4.67,4.67); Calibrated: 9/12/2017, * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn1525; Calibrated: 2017—10—02 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/3 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration /Pin=100mW, d=10mm, f=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 65.11 V/im; Power Drift = —0.01 dB Peak SAR (extrapolated) = 32.2 Wikg SAR(1 g) =7.09 Wikg; SAR(10 g) = 1.98 Wikg Maximum value of SAR (measured) = 17.3 Wikg Dipole Calibration /Pin=100mW, d=10mm, f=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.15 V/im; Power Drift = —0.03 dB Peak SAR (extrapolated) = 33.3 Wikg SAR(1 g) =7.12 Wikg; SAR(10 g) = 1.98 Wikg Maximum value of SAR (measured) = 17.5 W/kg Certificate No: Z18—60042 Page 14 of 16 1EL. +o9 61 uuurruuuy r m Tuy 6+ vuvruuys sope>

ECIT 7TTr a s e Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—25 12 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp=//wwwchinattl.en Dipole Calibration /Pin=100mW, d=10mm, f=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 65.49 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 37.5 W/kg SAR(1 g) = 7.72 Wikg; SAR(10 g) = 2.14 Wikg Maximum value of SAR (measured) = 19.5 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 64.69 V/im; Power Drift = 0.00 dB Peak SAR (extrapolated) = 36.4 Wikg SAR(1 g) = 7.52 Wikg; SAR(10 g) = 2.1 Wikg Maximum value of SAR (measured) = 18.5 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.28 V/im; Power Drift = 0.00 dB Peak SAR (extrapolated) = 37.9 Wikg SAR(1 g) =7.27 Wikg; SAR(10 g) = 2.02 Wikg Maximum value of SAR (measured) = 18.5 Wkg dB 0 —8.44 —16.89 —25.33 —33.78 ~42.22 | . 0 dB = 18.5 Wikg = 12.67 dBWikg Certificate No: Z18—60042 Page 15 of 16 LLL. 9U 64 uuurruwuy i rva. Tuu ef vuvcruwe + nepecs ce en e n en

Report No.: I19D00082-SAR01 East China Institute of Telecommunications Page Number : 211 of 212 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date: August 13, 2019

Report No.: I19D00082-SAR01 ANNEX E. Accreditation Certificate **********End of the Report********** East China Institute of Telecommunications Page Number : 212 of 212 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date: August 13, 2019


Document Created: 2019-08-16 11:10:44
Document Modified: 2019-08-16 11:10:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC