User Manual

FCC ID: 2AGNTEVOA2400A

Users Manual

Download: PDF
FCCID_4089922





REMOTE CONTROL 1. Mobile Device Holder 2. Flight Information Panel 3. Command Sticks 4. Hand Grips 5. Take—offLanding Button 6. Power Button 7. USB Ports > 8. Pause Button . 9. Go Home Bution e 10. Antennas 00 11. Screen Navigation Dial 12. Screen Navigation Button 13. Shutter Button un me® $ 14. Customizable Button A a 15. Customizable Button B 16. Record Button 17. Gimbal Pitch Dial CHARGING THE AIRCRAFT & REMOTE CONTROL The aircraft battery and remote control can be charged simultaneously using the supplied charger and following the staps below. 1.Aircraft Battery: Plug the connector cable into the charging port. IMPORTANT:The aircraft battery isn‘t activated out of the box. Plug the charging connector into the battery to activateit before initial use. 4

2. Remote Control: Open the USB port‘s protective cover. Then plug the USB charging cable into the port. 3. Plug in the charger to a power outlet. NOTE: Always fly with both aircraft and remote control batteries fully charged. For a complete charge, theaircraft battery requires approximately 80 minutes, and the remote control 180 minutes. 7. INSTALLING THE AUTEL EXPLORER "APP (OPTIONAL) While the aircraft can be flown using only the remote control, our mobile app offers you access to advanced flight, photography and video functionality. Follow the steps below to get connected. 1. Search for "Autel Explorer" from the App Store or Google Play and install the app for EVO on your mobile device. 2. Launch the app on your mobile device. 3. Connect the mobile device to the remote control by following the onscreen prompts. I ocm » NOTE: Autel Explorer"* supports iOS 9.0 or later and Android 4.4 or later.

8. PREPARING THE AIRCRAFT 1. Remove the gimbal holder, as well as the warning cards from the motors. 2. Unfold the front arms and propellers. A 3. Unfold the rear arms and propellers. IMPORTANT: Usage: Unfold the front arms first, then the rear arms. Storage: Fold the rear arms first, then the front arms. 9. INSTALLING NEW PROPELLERS Because the propellers come attached to the aircraft, the following instructions apply if you need to reinstall propellers. Propellers must be undamaged and firmly attached. The propellers and motors are color—coded in order to clearly mark how they should be paired.

Attaching the Propellers 1. Make sure the aircraft is powered off. 2. Match the propeller to its paired motor according to the color code. P 3. Press down and rotate in the lock direction until the propeller is firmly attached. _ .0y Detaching the Propellers 1. Make sure the aircraft is powered off. 2. Press each propeller down firmly and rotate in the unlock direction to detach the propeller. NOTE: When the aircraft is not in use, we recommend folding in the arms and propellers. 10. PREPARING THE REMOTE CONTROL 1. Unfold the mobile device holder, antannas, and hand grips. L A @ |*| ® w a 2. Position the antennas vertically in order to ensure the strongest possible signal. T 2 Strong Weak

11. POWERING UP 1. Press and hold the power button for 2 seconds. 2. Press and hold the aircraft power button for 3 seconds. The current battery level will be clearly displayed. IMPORTANT: Make sure that you always tum on the remote control before turning on the aircraft. Similarly, the aircraft should be powered down before turning off the remote control. 12. TAKEOFF 1. Place the aircraft on a level surface. Stand well clear of the rear of the aircraft. 2. Start the motors by holding both command sticks for two seconds in one of these positions: 3. With the motors spinning, choose one of the following methods to take off: Hold the Takeoff/Landing Push the Left Command Button for 2s Stick slowly upward {Mode 2)


14. LANDING & MOTOR SHUTDOWN (MODE 2) IMPORTANT: Make sure to land the aircraft on a flat and level surface in an open area. 1. Choose one of the following methods to land the aircraft: Hold the Takeoff/Landing Push the Left Command Stick Button for 2s slowly downwards 2. After landing, shut down the motors by one of the following methods: Push the Left Command Stick Hold both Command Sticks to the bottom and hold for 2s tos—in for 2s 10




FCC Compliance FCC Warning Message                       the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: For EVO Pro This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For EF7- 1, SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the device. when used, please keep the distance with a minimum of 10mm from the body. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. ISEDC RSS warning This device complies with ISEDC licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent areil est conforme aux CNR d'Industrie Canada licables aux areils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'areil ne doit pas produire de brouillage, et (2) l'utilisateur de l'areil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISEDC Radiation Exposure Statement: For EVO Pro This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. For EF7- 1, SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the device. when used, please keep the distance with a minimum of 10mm from the body.                      void the user’s authority to operate the equipment.



Document Created: 2019-03-27 11:36:27
Document Modified: 2019-03-27 11:36:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC