Test Report

FCC ID: 2AGNTAC5809A

Test Report

Download: PDF
FCCID_2883801

FCC PART 15.407 TEST REPORT For Autel Robotics Co., Ltd. 9th Floor, Bldg.B1, Zhiyuan, 1001 Xueyuan Rd., Xili, Nanshan, Shenzhen, China FCC ID: 2AGNTAC5809A Report Type: Product Type: Original Report X-Star series Test Engineer: Simon Wang Report Number: RSZ151118002-00A Report Date: 2015-12-16 Bell Hu Reviewed By: RF Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp.

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A TABLE OF CONTENTS GENERAL INFORMATION .......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3 OBJECTIVE ...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................3 TEST METHODOLOGY ..................................................................................................................................................3 TEST FACILITY .............................................................................................................................................................3 SYSTEM TEST CONFIGURATION ..........................................................................................................................4 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................4 EUT EXERCISE SOFTWARE ..........................................................................................................................................4 EQUIPMENT MODIFICATIONS .......................................................................................................................................4 EXTERNAL I/O CABLE..................................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................5 SUMMARY OF TEST RESULTS ...............................................................................................................................6 FCC §15.407 (f) & §2.1091 – MAXIMUM PERMISSIBLE EXPOSURE (MPE) ......................................................7 APPLICABLE STANDARD ..............................................................................................................................................7 FCC §15.203 – ANTENNA REQUIREMENT ............................................................................................................8 APPLICABLE STANDARD ..............................................................................................................................................8 ANTENNA CONNECTOR CONSTRUCTION ......................................................................................................................8 FCC §15.205 & §15.209 & §15.407(B) (4),(6),(7) – UNDESIRABLE EMISSION ...................................................9 APPLICABLE STANDARD ..............................................................................................................................................9 MEASUREMENT UNCERTAINTY ....................................................................................................................................9 EUT SETUP ..................................................................................................................................................................9 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................10 TEST PROCEDURE ......................................................................................................................................................10 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................11 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................11 TEST RESULTS SUMMARY ..........................................................................................................................................12 TEST DATA ................................................................................................................................................................12 FCC §15.407(a) (1) – 99% OCCUPIED & 6dB EMISSION BANDWIDTH .........................................................15 APPLICABLE STANDARD ............................................................................................................................................15 TEST PROCEDURE ......................................................................................................................................................15 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................15 TEST DATA ................................................................................................................................................................16 FCC §15.407(a) (3) – CONDUCTED TRANSMITTER OUTPUT POWER .........................................................20 APPLICABLE STANDARD ............................................................................................................................................20 TEST PROCEDURE ......................................................................................................................................................20 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................20 TEST DATA ................................................................................................................................................................21 FCC §15.407(a) (3) – POWER SPECTRAL DENSITY ...........................................................................................25 APPLICABLE STANDARD ............................................................................................................................................25 TEST PROCEDURE ......................................................................................................................................................25 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................25 TEST DATA ................................................................................................................................................................26 FCC Part 15.407 Page 2 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A GENERAL INFORMATION Product Description for Equipment under Test (EUT) The Autel Robotics Co., Ltd.’s product, model number: X-Star Premium (FCC ID: 2AGNTAC5809A) or the "EUT" in this report was an X-Star series, which was measured approximately: 31.5 cm (L) x16.7 cm (W) x 20.0 cm (H), rated with input voltage: DC 14.8V Li-Po battery. *All measurement and test data in this report was gathered from production sample serial number: 1507133 (Assigned by BACL, Shenzhen). The EUT supplied by the applicant was received on 2015-11-18. Objective This type approval report is prepared on behalf of Autel Robotics Co., Ltd. in accordance with Part 2- Subpart J, Part 15-Subparts A, B and E of the Federal Communication Commissions rules. The tests were performed in order to determine compliance with FCC Part 15, Subpart E, section 15.203, 15.205, 15.207, 15.209 and 15.407 rules. Related Submittal(s)/Grant(s) FCC Part 15.247 DTS submissions with FCC ID: 2AGNTAC5809A. Part 15.407 NII submission with FCC ID: 2AGNTRC5809A. Test Methodology All measurements contained in this report were conducted with ANSI C63.10-2013, American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices. All emissions measurement was performed and Bay Area Compliance Laboratories Corp. (Shenzhen). The radiated testing was performed at an antenna-to-EUT distance of 3 meters. Measurement uncertainty with RF radiated emission is 5.91 dB for 30MHz-1GHz.and 4.92 dB for above 1GHz, 1.95dB for conducted measurement. Test Facility The test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located on the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China. Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on October 31, 2013. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-2014. The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: 382179. The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. FCC Part 15.407 Page 3 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A SYSTEM TEST CONFIGURATION Description of Test Configuration The system was configured for testing in an engineering mode, which was provided by manufacturer. Frequency Frequency Frequency Channel Channel Channel (MHz) (MHz) (MHz) 1 5727 26 5752 51 5777 2 5728 27 5753 52 5778 3 5729 28 5754 53 5779 4 5730 29 5755 54 5780 5 5731 30 5756 55 5781 6 5732 31 5757 56 5782 7 5733 32 5758 57 5783 8 5734 33 5759 58 5784 9 5735 34 5760 59 5785 10 5736 35 5761 60 5786 11 5737 36 5762 61 5787 12 5738 37 5763 62 5788 13 5739 38 5764 63 5789 14 5740 39 5765 64 5790 15 5741 40 5766 65 5791 16 5742 41 5767 66 5792 17 5743 42 5768 67 5793 18 5744 43 5769 68 5794 19 5745 44 5770 69 5795 20 5746 45 5771 70 5796 21 5747 46 5772 71 5797 22 5748 47 5773 72 5798 23 5749 48 5774 73 5799 24 5750 49 5775 25 5751 50 5776 EUT was tested with Channel 1, 34 and 73. EUT Exercise Software No exercise software was used. Equipment Modifications No modification was made to the EUT tested. FCC Part 15.407 Page 4 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A External I/O Cable Cable Description Length (m) From/Port To / / / / Block Diagram of Test Setup Below 1GHz: 1.0 Meter EUT Non-conductive table 80 cm above Ground Plane 1.5 Meters Above 1GHz: 1.0 Meter EUT Non-conductive table 150 cm above Ground Plane 1.5 Meters FCC Part 15.407 Page 5 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A SUMMARY OF TEST RESULTS FCC Rules Description of Test Result §15.407 (f), §2.1091 Maximum Permissible Exposure (MPE) Compliance §15.203 Antenna Requirement Compliance §15.407(b)(6) & §15.207(a) Conducted Emissions Not Applicable FCC §15.205 & §15.209 & Undesirable Emission Compliance §15.407(b) (4),(6),(7) §15.407(b) (4) Band edge Compliance §15.407(a) (1),(5),(e) 99% Occupied & 6dB Emission Bandwidth Compliance §15.407(a) (3) Conducted Transmitter Output Power Compliance §15.407 (a) (3) Power Spectral Density Compliance Not Applicable: The EUT was powered by battery. FCC Part 15.407 Page 6 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A FCC §15.407 (f) & §2.1091 – MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to FCC §2.1091 and §1.1307(b) (1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (mW/cm2) (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculated Formulary: Predication of MPE limit at a given distance S = PG/4R² = power density (in appropriate units, e.g. mW/cm2); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); Calculated Data: Max tune –up Antenna Gain Conducted Evaluation Frequency Power Density MPE Limit Power Distance (MHz) (mW/cm2) (mW/cm2) (cm) (dBi) (numeric) (dBm) (mW) 5727-5799 2.5 1.78 16.00 39.8 20 0.0141 1.0 Note: To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 20cm from nearby persons. Result: Compliance FCC Part 15.407 Page 7 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A FCC §15.203 – ANTENNA REQUIREMENT Applicable Standard According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the user of a standard antenna jack or electrical connector is prohibited. The structure and application of the EUT were analyzed to determine compliance with section §15.203 of the rules. §15.203 state that the subject device must meet the following criteria: a. Antenna must be permanently attached to the unit. b. Antenna must use a unique type of connector to attach to the EUT. Unit must be professionally installed, and installer shall be responsible for verifying that the correct antenna is employed with the unit. And according to FCC 47 CFR section 15.407 (a), if the transmitting antennas of directional gain greater than 6dBi are used, the transmit power and power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. Antenna Connector Construction The EUT has an internal antenna arrangement, which was permanently attached and the antenna gain is 2.5 dBi, fulfill the requirement of this section. Please refer to the EUT photos. Result: Compliance. FCC Part 15.407 Page 8 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A FCC §15.205 & §15.209 & §15.407(B) (4),(6),(7) – UNDESIRABLE EMISSION Applicable Standard FCC §15.407 (b) (4), (6), (7); §15.205; §15.209; For transmitters operating in the 5.725–5.825 GHz band: all emissions within the frequency range from the band edge to 10 MHz above or below the band edge shall not exceed an EIRP of –17 dBm/MHz; for frequencies 10 MHz or greater above or below the band edge, emissions shall not exceed an EIRP of –27 dBm/MHz. Unwanted emissions below 1 GHz must comply with the general field strength limits set forth in §15.209. Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on CISPR 16-4-2:2011, the expended combined standard uncertainty of radiation emissions at Bay Area Compliance Laboratories Corp. (Shenzhen) is 5.91 dB for 30MHz-1GHz and 4.92 dB for above 1GHz, 1.95dB for conducted measurement at antenna port. And the uncertainty will not be taken into consideration for the test data recorded in the report EUT Setup Below 1GHz: FCC Part 15.407 Page 9 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Above 1GHz: The setup of EUT is according with per ANSI C63.10-2013 measurement procedure. The specification used was with the FCC Part 15.209 limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. EMI Test Receiver & Spectrum Analyzer Setup The system was investigated from 30 MHz to 40 GHz. During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set with the following configurations: Frequency Range RBW Video B/W IF B/W Detector 30 MHz – 1000 MHz 100 kHz 300 kHz 120 kHz QP 1 MHz 3 MHz / PK Above 1 GHz 1 MHz 10 Hz / Ave. Test Procedure Radiated Spurious Emission During the radiated emission test, the adapter was connected to the AC floor outlet. Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all the installation combinations. Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz-40GHz, peak and Average detection modes for frequencies above 1GHz. The EUT is set 3.0 meter away from the testing antenna, which is varied from 1-4 meters, and the EUT is placed on a turntable, the table shall be rotated for 360 degrees to find out the highest emission. The receiving antenna should be changed the polarization both of horizontal and vertical. FCC Part 15.407 Page 10 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Conducted Spurious Emission at Antenna Port 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. The Resolution bandwidth is set to 1MHz, The Video bandwidth is set to ≥ 1MHz, report the peak value out of the oprating band. 3. Repeat above procedures until all frequencies measured were complete. EUT Signal Analyzer Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit – Corrected Amplitude Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date HP Amplifier HP8447E 1937A01046 2015-05-06 2016-05-06 Rohde & Schwarz EMI Test Receiver ESCI 101120 2015-11-03 2016-11-03 Sunol Sciences Bi-log Antenna JB1 A040904-2 2014-12-07 2017-12-06 Mini Amplifier ZVA-183-S+ 5969001149 2015-04-23 2016-04-23 A.H. System Horn Antenna SAS-200/571 135 2015-08-18 2018-08-17 Rohde & Schwarz Signal Analyzer FSIQ26 8386001028 2015-12-11 2016-12-11 ALN- DUCOMMUN Pre-amplifier 991373-01 2015-08-03 2016-08-03 22093530-01 Agilent Spectrum Analyzer 8564E 3943A01781 2013-05-09 2016-05-08 the electro- Horn Antenna 3116 9510-2270 2013-10-14 2016-10-13 Mechanics Co. * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements that traceable to National Primary Standards and International System of Units (SI). FCC Part 15.407 Page 11 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Test Results Summary According to the recorded data in following table, the EUT complied with the FCC Title 47, Part 15, Subpart C, Section 15.205, 15.209 and 15.407, the worst margin reading as below: 0.32 dB at 5724.75 MHz in the Vertical polarization for Left Side Band. Refer to CISPR16-4-2:2011 and CISPR 16-4-1:2009, the measured level is in compliance with the limit if Lm + U(Lm) ≤ Llim + Ucispr In BACL, U(Lm) is less than Ucispr, if Lm is less than Llim, it implies that the EUT complies with the limit. Test Data Environmental Conditions Temperature: 26 ℃ Relative Humidity: 53 % ATM Pressure: 101.0 kPa The testing was performed by Simon Wang on 2015-12-12. EUT operation mode: Transmitting FCC Part 15.407 Page 12 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A 30 MHz-40 GHz: Frequency Receiver Turntable Rx Antenna Corrected Corrected FCC Part 15.407 Reading Detector Height Polar Factor Amplitude Limit Margin (MHz) Degree dB (dBμV/m) (dBμV/m) (dBμV) (PK/QP/AV) (m) (H / V) (dB) Low Channel (5727 MHz) 256.8 44.15 QP 201 1.2 H -13.9 30.25 46 15.75 5727.00 62.16 PK 301 2.0 H 42.48 104.64 / / 5727.00 48.78 Ave. 301 2.0 H 42.48 91.26 / / 5727.00 65.37 PK 89 1.3 V 42.48 107.85 / / 5727.00 51.29 Ave. 89 1.3 V 42.48 93.77 / / 11454.00 35.08 PK 320 2.3 H 27.36 62.44 74 11.56 11454.00 18.34 Ave. 320 2.3 H 27.36 45.70 54 8.30 11454.00 32.19 PK 101 1.7 V 27.36 59.55 74 14.45 11454.00 17.45 Ave. 101 1.7 V 27.36 44.81 54 9.19 Middle Channel (5760 MHz) 256.8 44.52 QP 201 1.2 H -13.9 30.62 46 15.38 5760.00 67.95 PK 71 1.1 H 42.39 110.34 / / 5760.00 53.71 Ave. 71 1.1 H 42.39 96.10 / / 5760.00 73.06 PK 179 2.3 V 42.39 115.45 / / 5760.00 59.54 Ave. 179 2.3 V 42.39 101.93 / / 11520.00 33.72 PK 50 1.6 H 27.36 61.08 74 12.92 11520.00 17.00 Ave. 50 1.6 H 27.36 44.36 54 9.64 11520.00 37.21 PK 234 1.9 V 27.36 64.57 74 9.43 11520.00 20.52 Ave. 234 1.9 V 27.36 47.88 54 6.12 High Channel (5799 MHz) 256.8 44.44 QP 201 1.2 H -13.9 30.54 46 15.46 5799.00 61.87 PK 75 2.1 H 42.39 104.26 / / 5799.00 48.24 Ave. 75 2.1 H 42.39 90.63 / / 5799.00 62.81 PK 304 1.7 V 42.39 105.20 / / 5799.00 48.78 Ave. 304 1.7 V 42.39 91.17 / / 11598.00 32.61 PK 50 1.8 H 28.49 61.10 74 12.90 11598.00 17.11 Ave. 50 1.8 H 28.49 45.60 54 8.40 11598.00 34.53 PK 92 1.9 V 28.49 63.02 74 10.98 11598.00 18.35 Ave. 92 1.9 V 28.49 46.84 54 7.16 Note: Corrected Amplitude = Corrected Factor + Reading Corrected Factor=Antenna factor (RX) + Cable Loss – Amplifier Factor Margin = Limit- Corr. Amplitude FCC Part 15.407 Page 13 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A BAND EDGE: Frequency Receiver Turntable Rx Antenna Corrected Corrected FCC Part 15.407 Reading Detector Height Polar Factor Amplitude Limit Margin (MHz) Degree dB (dBμV/m) (dBμV/m) (dBμV) (PK/QP/AV) (m) (H / V) (dB) Left Side Band 5724.75 45.12 PK 125 1.7 H 15.54 60.66 74 13.34 5724.75 37.71 Ave. 125 1.7 H 15.54 53.25 54 0.75 5724.75 46.53 PK 89 1.5 V 15.54 62.07 74 11.93 5724.75 38.14 Ave. 89 1.5 V 15.54 53.68 54 0.32 Right Side Band 5856.37 30.45 PK 177 1.7 H 15.23 45.68 74 28.32 5856.37 25.86 Ave. 177 1.7 H 15.23 41.09 54 12.91 5856.37 31.52 PK 204 1.5 V 15.23 46.75 74 27.25 5856.37 26.37 Ave. 204 1.5 V 15.23 41.6 54 12.40 Note: Corrected Amplitude = Corrected Factor + Reading Corrected Factor=Antenna factor (RX) + Cable Loss – Amplifier Factor Margin = Limit- Corr. Amplitude FCC Part 15.407 Page 14 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A FCC §15.407(a) (1) – 99% OCCUPIED & 6dB EMISSION BANDWIDTH Applicable Standard The maximum power spectral density is measured as a conducted emission by direct connection of a calibrated test instrument to the equipment under test. If the device cannot be connected directly, alternative techniques acceptable to the Commission may be used. Measurements in the 5.725-5.85 GHz band are made over a reference bandwidth of 500 kHz or the 26 dB emission bandwidth of the device, whichever is less. Measurements in the 5.15-5.25 GHz, 5.25-5.35 GHz, and the 5.47-5.725 GHz bands are made over a bandwidth of 1 MHz or the 26 dB emission bandwidth of the device, whichever is less. A narrower resolution bandwidth can be used, provided that the measured power is integrated over the full reference bandwidth. Within the 5.725-5.85 GHz band, the minimum 6 dB bandwidth of U-NII devices shall be at least 500 kHz. Test Procedure 1. Emission Bandwidth (EBW) a) Set RBW = approximately 1% of the emission bandwidth. b) Set the VBW > RBW. c) Detector = Peak. d) Trace mode = max hold. e) Measure the maximum width of the emission that is 26 dB down from the maximum of the emission. Compare this with the RBW setting of the analyzer. Readjust RBW and repeat measurement as needed until the RBW/EBW ratio is approximately 1%. 2. Minimum Emission Bandwidth for the band 5.725-5.85 GHz Section 15.407(e) specifies the minimum 6 dB emission bandwidth of at least 500 KHz for the band 5.715- 5.85 GHz. The following procedure shall be used for measuring this bandwidth: a) Set RBW = 100 kHz. b) Set the video bandwidth (VBW) ≥ 3 × RBW. c) Detector = Peak. d) Trace mode = max hold. e) Sweep = auto couple. f) Allow the trace to stabilize. g) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. Signal Analyzer EUT Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date Rohde & Schwarz Signal Analyzer FSIQ26 8386001028 2015-12-11 2016-12-11 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). FCC Part 15.407 Page 15 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Test Data Environmental Conditions Temperature: 26 ℃ Relative Humidity: 51 % ATM Pressure: 101.0 kPa The testing was performed by Simon Wang on 2015-12-12 and 2015-12-22. EUT operation mode: Transmitting Test Result: Pass Please refer to the following tables and plots. Occupied Frequency 6dB Bandwidth Limit Channel Bandwidth (MHz) (MHz) (kHz) (MHz) Low 5727 1.703 1.072 ≥500 Middle 5760 1.874 1.152 ≥500 High 5799 1.804 1.112 ≥500 6dB Emission Bandwidth, Low Channel Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl 1.00 dB VBW 300 kHz 24 dBm 1.07214429 MHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 9.12 dBm 20 A 5.72643387 GHz D1 15.57 dBm 1 1 1 [T1] 1.00 dB 10 D2 9.57 dBm 1.07214429 MHz 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76 Center 5.727 GHz 500 kHz/ Span 5 MHz Date: 12.DEC.2015 14:11:34 FCC Part 15.407 Page 16 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A 6dB Emission Bandwidth, Middle Channel Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl 0.86 dB VBW 300 kHz 24 dBm 1.15230461 MHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 9.23 dBm 20 A D1 16.06 dBm 5.75935371 GHz 1 1 1 [T1] 0.86 dB 10 D2 10.06 dBm 1.15230461 MHz 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76 Center 5.76 GHz 500 kHz/ Span 5 MHz Date: 12.DEC.2015 14:59:05 6dB Emission Bandwidth, High Channel Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl 0.38 dB VBW 300 kHz 24 dBm 1.11222445 MHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 9.24 dBm 20 A 5.79839379 GHz D1 15.37 dBm 1 1 1 [T1] 0.38 dB 10 D2 9.37 dBm 1.11222445 MHz 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76 Center 5.799 GHz 500 kHz/ Span 5 MHz Date: 12.DEC.2015 14:46:17 FCC Part 15.407 Page 17 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A 99% Occupied Bandwidth, Low Channel Marker 1 [T1] RBW 30 kHz RF Att 30 dB Ref Lvl 14.47 dBm VBW 100 kHz 29.5 dBm 5.72697495 GHz SWT 14 ms Unit dBm 29.5 10.5 dB Offset 1 [T1] 14.47 dBm A 5.72697495 GHz 20 OPB 1.70340681 MHz 1 T1 [T1] -8.90 dBm 10 5.72613327 GHz T2 [T1] -9.06 dBm 5.72783667 GHz 0 1MAX 1MA T1 T2 -10 -20 -30 -40 -50 -60 -70.5 Center 5.727 GHz 500 kHz/ Span 5 MHz Date: 22.DEC.2015 15:21:33 99% Occupied Bandwidth, Middle Channel Marker 1 [T1] RBW 30 kHz RF Att 30 dB Ref Lvl 15.26 dBm VBW 100 kHz 29.5 dBm 5.75994489 GHz SWT 14 ms Unit dBm 29.5 10.5 dB Offset 1 [T1] 15.26 dBm A 5.75994489 GHz 20 1 OPB 1.87374749 MHz T1 [T1] -6.94 dBm 10 5.75903307 GHz T2 [T1] -7.70 dBm 5.76090681 GHz 0 1MAX T1 T2 1MA -10 -20 -30 -40 -50 -60 -70.5 Center 5.76 GHz 500 kHz/ Span 5 MHz Date: 22.DEC.2015 16:29:39 FCC Part 15.407 Page 18 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A 99% Occupied Bandwidth, High Channel Marker 1 [T1] RBW 30 kHz RF Att 30 dB Ref Lvl 14.56 dBm VBW 100 kHz 29.5 dBm 5.79895491 GHz SWT 14 ms Unit dBm 29.5 10.5 dB Offset 1 [T1] 14.56 dBm A 5.79895491 GHz 20 1 OPB 1.80360721 MHz T1 [T1] -7.10 dBm 10 5.79806313 GHz T2 [T1] -7.73 dBm 5.79986673 GHz 0 1MAX T1 T2 1MA -10 -20 -30 -40 -50 -60 -70.5 Center 5.799 GHz 500 kHz/ Span 5 MHz Date: 22.DEC.2015 16:24:43 FCC Part 15.407 Page 19 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A FCC §15.407(a) (3) – CONDUCTED TRANSMITTER OUTPUT POWER Applicable Standard For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. Test Procedure Set span to encompass the entire EBW (or, alternatively, the entire 99% occupied bandwidth) of the signal. (ii) Set RBW = 1 MHz. (iii) Set VBW ≥ 3 MHz. (iv) Number of points in sweep ≥ 2 Span / RBW. (This ensures that bin-to-bin spacing is ≤ RBW/2, so that narrowband signals are not lost between frequency bins.) (v) Manually set sweep time ≥ 10 * (number of points in sweep) * (symbol period of the transmitted signal), but not less than the automatic default sweep time. (vi) Set detector = RMS. (vii) The EUT shall be operated at 100 percent duty cycle. (viii) Perform a single sweep. (ix) Compute power by integrating the spectrum across the EBW (or, alternatively, the entire 99% occupied bandwidth) of the signal using the instrument’s band power measurement function with band limits set equal to the EBW (or occupied bandwidth) band edges. If the instrument does not have a band power function, sum the spectrum levels (in power units) at 1 MHz intervals extending across the EBW (or, alternatively, the entire 99% occupied bandwidth) of the spectrum. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date Rohde & Schwarz Signal Analyzer FSIQ26 8386001028 2015-12-11 2016-12-11 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). FCC Part 15.407 Page 20 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Test Data Environmental Conditions Temperature: 23 ℃ Relative Humidity: 50 % ATM Pressure: 101.0 kPa The testing was performed by Simon Wang on 2015-12-12. EUT operation mode: Transmitting Test Result: Pass Max Conducted Max Conducted Frequency Average Output Limit Channel Peak Output Power (MHz) Power (dBm) (dBm) (dBm) Low 5727 16.24 15.47 30 Middle 5760 16.22 15.81 30 High 5799 15.42 15.08 30 FCC Part 15.407 Page 21 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Peak Conducted Output Power, Low Channel Marker 1 [T1] RBW 3 MHz RF Att 30 dB Ref Lvl 16.24 dBm VBW 3 MHz 24 dBm 5.72656914 GHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 16.24 dBm 20 A 1 5.72656914 GHz 10 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76 Center 5.727 GHz 1 MHz/ Span 10 MHz Date: 12.DEC.2015 14:03:25 Peak Conducted Output Power, Middle Channel Marker 1 [T1] RBW 3 MHz RF Att 30 dB Ref Lvl 16.22 dBm VBW 3 MHz 24 dBm 5.76033066 GHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 16.22 dBm 20 A 1 5.76033066 GHz 10 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76 Center 5.76 GHz 1 MHz/ Span 10 MHz Date: 12.DEC.2015 14:53:01 FCC Part 15.407 Page 22 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Peak Conducted Output Power, High Channel Marker 1 [T1] RBW 3 MHz RF Att 30 dB Ref Lvl 15.42 dBm VBW 3 MHz 24 dBm 5.79844890 GHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 15.42 dBm 20 A 1 5.79844890 GHz 10 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76 Center 5.799 GHz 1 MHz/ Span 10 MHz Date: 12.DEC.2015 14:41:30 Average Conducted Output Power, Low Channel Marker 1 [T1] RBW 3 MHz RF Att 30 dB Ref Lvl 15.47 dBm VBW 3 MHz 24 dBm 5.72690982 GHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 15.47 dBm 20 A 1 5.72690982 GHz 10 0 -10 1MAX 1RM -20 -30 -40 -50 -60 -70 -76 Center 5.727 GHz 1 MHz/ Span 10 MHz Date: 12.DEC.2015 14:04:07 FCC Part 15.407 Page 23 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Average Conducted Output Power, Middle Channel Marker 1 [T1] RBW 3 MHz RF Att 30 dB Ref Lvl 15.81 dBm VBW 3 MHz 24 dBm 5.75948898 GHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 15.81 dBm 20 A 1 5.75948898 GHz 10 0 -10 1MAX 1RM -20 -30 -40 -50 -60 -70 -76 Center 5.76 GHz 1 MHz/ Span 10 MHz Date: 12.DEC.2015 14:53:34 Average Conducted Output Power, High Channel Marker 1 [T1] RBW 3 MHz RF Att 30 dB Ref Lvl 15.08 dBm VBW 3 MHz 24 dBm 5.79856914 GHz SWT 5 ms Unit dBm 24 4 dB Offset 1 [T1] 15.08 dBm 20 A 1 5.79856914 GHz 10 0 -10 1MAX 1RM -20 -30 -40 -50 -60 -70 -76 Center 5.799 GHz 1 MHz/ Span 10 MHz Date: 12.DEC.2015 14:42:00 FCC Part 15.407 Page 24 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A FCC §15.407(a) (3) – POWER SPECTRAL DENSITY Applicable Standard For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. Test Procedure For devices operating in the bands 5.15-5.25 GHz, 5.25-5.35 GHz, and 5.47-5.725 GHz, the above procedures make use of 1 MHz RBW to satisfy directly the 1 MHz reference bandwidth specified in § 15.407(a)(5). For devices operating in the band 5.725-5.85 GHz, the rules specify a measurement bandwidth of 500 kHz. Many spectrum analyzers do not have 500 kHz RBW, thus a narrower RBW may need to be used. The rules permit the use of a RBWs less than 1 MHz, or 500 kHz, “provided that the measured power is integrated over the full reference bandwidth” to show the total power over the specified measurement bandwidth (i.e., 1 MHz, or 500 kHz). If measurements are performed using a reduced resolution bandwidth (< 1 MHz, or < 500 kHz) and integrated over 1 MHz, or 500 KHz bandwidth, the following adjustments to the procedures apply: a) Set RBW 1/T, where T is defined in section II.B.l.a). b) Set VBW 3 RBW. c) If measurement bandwidth of Maximum PSD is specified in 500 kHz, add 10log(500kHz/RBW) to the measured result, whereas RBW (< 500 KHz) is the reduced resolution bandwidth of the spectrum analyzer set during measurement. d) If measurement bandwidth of Maximum PSD is specified in 1 MHz, add 10log(1MHz/RBW) to the measured result, whereas RBW (< 1 MHz) is the reduced resolution bandwidth of spectrum analyzer set during measurement. e) Care must be taken to ensure that the measurements are performed during a period of continuous transmission or are corrected upward for duty cycle. Note: As a practical matter, it is recommended to use reduced RBW of 100 KHz for the sections 5.c) and 5.d) above, since RBW=100 KHZ is available on nearly all spectrum analyzers. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date Rohde & Schwarz Signal Analyzer FSIQ26 8386001028 2015-12-11 2016-12-11 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). FCC Part 15.407 Page 25 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Test Data Environmental Conditions Temperature: 26 ℃ Relative Humidity: 51 % ATM Pressure: 101.0 kPa The testing was performed by Simon Wang from 2015-12-22. EUT operation mode: Transmitting Test Result: Pass Please refer to the following tables and plots. Frequency PSD Limit Channel (MHz) (dBm/500kHz) (dBm/500kHz) Low 5727 14.09 30 Middle 5760 15.65 30 High 5799 15.50 30 Power Spectral Density, Low Channel Marker 1 [T1] RBW 500 kHz RF Att 30 dB Ref Lvl 14.09 dBm VBW 2 MHz 29.5 dBm 5.72653407 GHz SWT 5 ms Unit dBm 29.5 10.5 dB Offset 1 [T1] 14.09 dBm A 5.72653407 GHz 20 1 10 0 1MAX 1RM -10 -20 -30 -40 -50 -60 -70.5 Center 5.727 GHz 500 kHz/ Span 5 MHz Date: 22.DEC.2015 16:18:25 FCC Part 15.407 Page 26 of 27

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSZ151118002-00A Power Spectral Density, Middle Channel Marker 1 [T1] RBW 500 kHz RF Att 30 dB Ref Lvl 15.65 dBm VBW 2 MHz 29.5 dBm 5.75951403 GHz SWT 5 ms Unit dBm 29.5 10.5 dB Offset 1 [T1] 15.65 dBm A 5.75951403 GHz 20 1 10 0 1MAX 1RM -10 -20 -30 -40 -50 -60 -70.5 Center 5.76 GHz 500 kHz/ Span 5 MHz Date: 22.DEC.2015 16:57:05 Power Spectral Density, High Channel Marker 1 [T1] RBW 500 kHz RF Att 30 dB Ref Lvl 15.50 dBm VBW 2 MHz 29.5 dBm 5.79853407 GHz SWT 5 ms Unit dBm 29.5 10.5 dB Offset 1 [T1] 15.50 dBm A 5.79853407 GHz 20 1 10 0 1MAX 1RM -10 -20 -30 -40 -50 -60 -70.5 Center 5.799 GHz 500 kHz/ Span 5 MHz Date: 22.DEC.2015 16:23:00 ***** END OF REPORT ***** FCC Part 15.407 Page 27 of 27


Document Created: 2017-11-16 03:37:03
Document Modified: 2017-11-16 03:37:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC