Modular Approval Letter

FCC ID: 2AGN8-ZM001

Cover Letter(s)

Download: PDF
FCCID_4480245

Sengled Co., Ltd. Declaration of the Modular Approval Applicant / Grantee Sengled Co., Ltd. FCC ID: 2AGN8-ZM001 Model: ZM001 The single module transmitter has been evaluated then tested meeting the requirements under Part 15C Section 212 as below: Modular approval requirement EUT Condition Com ply (a) The radio elements of the modular transmitter must have The radio elements of the modular YES their own shielding. The physical crystal and tuning transmitter have their own shielding. capacitors may be located external to the shielded radio elements. (b) The modular transmitter must have The modular has buffered data inputs, it is YES buffered modulation/data inputs (if such inputs are integrated in chip. Please see provided) to ensure that the module will comply with part schematic.pdf 15 requirements under conditions of excessive data rates or over-modulation. (c)The modular transmitter must have its All power lines derived from the host YES own power supply regulation. device are regulated before energizing other circuits internal to the ZM001. Please see schematic.pdf (d) The modular transmitter must comply A permanently attached antenna or unique YES with the antenna and transmission system requirements of antenna connector is not a requirement for Sections 15.203, 15.204(b) and 15.204(c). The antenna licensed modules. must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. (e)The modular transmitter must be tested The ZM001 was tested in a stand‐alone YES in a stand-alone configuration, i.e., the module must not be configuration via a PCMCIA extender. inside another device during testing for compliance with Please see conducted set‐up photo.pdf part 15 requirements. Unless the transmitter module will be and spurious set‐up battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these

Sengled Co., Ltd. lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i))must not be inside another device during testing. (f)The modular transmitter must be The label position of ZM001 is clearly YES equipped with either a permanently affixed label or must indicated. If the FCC ID of the module be capable of electronically displaying its FCC identification number. cannot be seen when it is installed, then the host label must include the text: Contains FCC ID: 2AGN8-ZM001. Please see the label.pdf (g) The modular transmitter must comply The ZM001 is compliant with all applicable YES with any specific rules or operating requirements that FCC rules. Detail instructions are given in ordinarily apply to a complete transmitter and the the User Manual. manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization requirements , which are based on the intended use/configurations. (h)The modular transmitter must comply The ZM001 is approved to comply with YES with any applicable RF exposure requirements in its final the applicable RF exposure requirement, configuration. please see the MPE evaluation with 20cm as the distance restriction. Dated : 2019/10/15 By:(Signature) (Printed) Jason Shi Title: Product Manager On behalf of: (Sengled Co., Ltd. )


Document Created: 2019-10-15 09:06:44
Document Modified: 2019-10-15 09:06:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC