Zigbee Test Report

FCC ID: 2AGN8-E1DG73

Test Report

Download: PDF
FCCID_4160366

RF TEST REPORT Applicant Sengled Co., Ltd. FCC ID 2AGN8-E1DG73 Product Smart Window & Door Sensor Brand sengled Marketing Smart Window & Door Sensor Model E1D-G73 Report No. R1812A0593-R1V1 Issue Date February 1, 2019 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC CFR47 Part 15C (2018). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Peng Tao Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86‐021‐50791141/2/3 FAX: +86‐021‐50791141/2/3‐8000

FCC RF Test Report Report No: R1812A0593-R1V1 TABLE OF CONTENT 1. Test Laboratory ............................................................................................................................ 4 1.1. Notes of the test report ......................................................................................................... 4 1.2. Test facility ........................................................................................................................... 4 1.3. Testing Location ................................................................................................................... 5 2. General Description of Equipment under Test.............................................................................. 6 3. Applied Standards ........................................................................................................................ 7 4. Test Configuration ........................................................................................................................ 8 5. Test Case Results ........................................................................................................................ 9 5.1. Maximum conducted output power ...................................................................................... 9 5.2. 6dB Bandwidth ................................................................................................................... 11 5.3. Band Edge ......................................................................................................................... 13 5.4. Power Spectral Density ...................................................................................................... 15 5.5. Spurious RF Conducted Emissions .................................................................................... 17 5.6. Unwanted Emission ........................................................................................................... 19 5.7. Conducted Emission .......................................................................................................... 31 6. Main Test Instruments ................................................................................................................ 33 ANNEX A: EUT Appearance and Test Setup .................................................................................... 34 A.1 EUT Appearance .................................................................................................................... 34 A.2 Test Setup .............................................................................................................................. 36 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 2 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Summary of measurement results Number Summary of measurements of results Clause in FCC rules Verdict 1 Maximum conducted output power 15.247(b)(3) PASS 2 6 dB bandwidth 15.247(a)(2) PASS 3 Maximum power spectral density 15.247(e) PASS 4 Band Edge 15.247(d) PASS 5 Spurious RF Conducted Emissions 15.247(d) PASS 6 Unwanted Emissions 15.247(d),15.205,15.209 PASS 7 Conducted Emissions 15.207 NA Date of Testing: December 26, 2018 ~ December 27, 2018 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 3 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 1. Test Laboratory 1.1. Notes of the test report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2. Test facility CNAS (accreditation number: L2264) TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS). FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. IC (recognition number is 8510A) TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. VCCI (recognition number is C-4595, T-2154, R-4113, G-10766) TA Technology (Shanghai) Co., Ltd. has been listed by industry Japan to perform electromagnetic emission measurement. A2LA (Certificate Number: 3857.01) TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 4 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 1.3. Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: xukai@ta-shanghai.com TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 5 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 2. General Description of Equipment under Test Client Information Applicant Sengled Co., Ltd. Room,Building 1, No.498, Guoshoujing Road, Pilot Free Trade Applicant address Zone, Shanghai, P.R. China Manufacturer Sengled Co., Ltd. Room,Building 1, No.498, Guoshoujing Road, Pilot Free Trade Manufacturer address Zone, Shanghai, P.R. China General information EUT Description Model: E1D-G73 SN: 1852D500215 Hardware Version: V0.2 Software Version: V0.2 Power Supply: Battery Antenna Type: Internal Antenna A permanently attached antenna (meet with the standard FCC Antenna Connector: Part 15.203 requirement) Test Mode: Zigbee Modulation Type: Zigbee: O-QPSK 1.45dBi for 2405MHz Antenna Gain: 1.70dBi for 2440MHz 1.57dBi for 2480MHz Directional Gain: NA additional beamforming gain: NA Max. Conducted Power 6.22 dBm Operating Frequency 2405 ~ 2480 MHz Range(s) Note: The information of the EUT is declared by the manufacturer. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 6 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 3. Applied Standards According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC CFR47 Part 15C (2018) Radio Frequency Devices ANSI C63.10 (2013) KDB 558074 D01 DTS Meas Guidance v05 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 7 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 4. Test Configuration Test Mode The EUT was programmed to be in continuously transmitting mode and the transmit duty cycle is not less than 98%. The EUT has been associated with peripherals and configuration operated in a manner tended to maximize its emission characteristics in a typical application. The radiated emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in lie-down position (X axis) and the worst case was recorded. Mode Channel Frequency 11 2405MHz 12 2410MHz 13 2415MHz 14 2420MHz 15 2425MHz 16 2430MHz 17 2435MHz 18 2440MHz Zigbee 19 2445MHz 20 2450MHz 21 2455MHz 22 2460MHz 23 2465MHz 24 2470MHz 25 2475MHz 26 2480MHz TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 8 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 5. Test Case Results 5.1. Maximum conducted output power Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement During the process of the testing, The EUT was connected to Spectrum Analyzer with a known loss. The EUT is max power transmission with proper modulation. The Average detector is used. We use Maximum Average Conducted Output Power Level Method in KDB 558074 D01 for this test. Test Setup Limits Rule Part 15.247 (b) (3) specifies that " For systems using digital modulation in the 902–928 MHz, 2400–2483.5 MHz: 1 Watt.” Average Output Power ≤ 1W (30dBm) Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.44 dB. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 9 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test Results Carrier Average Network Limit frequency Output Power Conclusion Standards (dBm) (MHz) (dBm) 2405 3.85 30 PASS Zigbee 2440 4.80 30 PASS 2480 6.22 30 PASS TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 10 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 5.2. 6dB Bandwidth Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to the spectrum analyzer through an external attenuator (20dB) and a known loss cable. RBW is set to 100 kHz; VBW is set to 300 kHz on spectrum analyzer. Test Setup Limits Rule Part 15.247 (a) (2) specifies that “Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.5 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz.” minimum 6 dB bandwidth ≥ 500 kHz Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 936 Hz. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 11 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test Results: 99% Minimum 6 dB Network Carrier frequency Limit bandwidth bandwidth Conclusion Standards (MHz) (kHz) (MHz) (MHz) 2405 2.4304 1.594 500 PASS Zigbee 2440 2.4537 1.613 500 PASS 2480 2.4547 1.627 500 PASS Zigbee, Carrier frequency (MHz): 2405 Zigbee, Carrier frequency (MHz): 2440 Zigbee, Carrier frequency (MHz): 2480 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 12 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 5.3. Band Edge Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to the spectrum analyzer through an external attenuator (20dB) and a known loss cable the band edge of the lowest and highest channels were measured. The peak detector is used and RBW is set to 100 kHz and VBW is set to 300 kHz on spectrum analyzer. Spectrum analyzer plots are included on the following pages. Test Setup Limits Rule Part 15.247(d) specifies that “In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits.” If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB.” Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96. Frequency Uncertainty 2GHz-3GHz 1.407 dB TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 13 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test Results: PASS Zigbee, Channel No.: 11 Zigbee, Channel No.: 26 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 14 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 5.4. Power Spectral Density Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to the spectrum analyzer through an external attenuator (20dB) and a known loss cable. RBW is set to 3 kHz and VBW is set to 10 kHz for Zigbee on spectrum analyzer. Set the span to 1.5 times the DTS channel bandwidth. Sweep time = auto couple. Trace mode = max hold. The peak power spectral density is recorded. Test setup Limits Rule Part 15.247(e) specifies that” For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. ‘’ Limits ≤ 8 dBm / 3kHz Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.75dB. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 15 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test Results: Power Spectral Network Channel Limit Density Conclusion Standards Number (dBm / 3kHz) (dBm / 3kHz) 11 -20.53 8 PASS Zigbee 18 -19.19 8 PASS 26 -17.80 8 PASS Zigbee, Channel No.: 11 Zigbee, Channel No.: 18 Zigbee, Channel No.: 26 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 16 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 5.5. Spurious RF Conducted Emissions Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to the spectrum analyzer with a known loss. The spectrum analyzer scans from 30MHz to the 10th harmonic of the carrier. The peak detector is used. Set RBW to100kHz and VBW to 300 kHz, Sweep is set to ATUO. The test is in transmitting mode. Limits Rule Part 15.247(d) pacifies that “In any 100 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power.” Carrier frequency Network Standards Reference value (dBm) Limit (MHz) 2405 0.49 -29.51 Zigbee 2440 1.45 -28.55 2480 -1.56 -31.56 Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96. Frequency Uncertainty 100kHz-2GHz 0.684 dB 2GHz-26GHz 1.407 dB TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 17 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test Results: The signal beyond the limit is carrier. Zigbee CH11 Zigbee CH18 Zigbee CH26 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 18 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 5.6. Unwanted Emission Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 102.5kPa Method of Measurement The test set-up was made in accordance to the general provisions of ANSI C63.10-2013.The Equipment Under Test (EUT) was set up on a non-conductive table in the semi-anechoic chamber. The test was performed at the distance of 3 m between the EUT and the receiving antenna. The turntable shall be rotated from 0 to 360 degrees for detecting the maximum of radiated spurious signal level. The measurements shall be repeated with orthogonal polarization of the test antenna. RBW is set to 100kHz.The data of cable loss and antenna factor has been calibrated in full testing frequency range before the testing. Sweep the whole frequency band through the range from 9kHz to the 10th harmonic of the carrier, and the emissions less than 20 dB below the permissible value are reported. The radiated emissions measurements were made in a typical installation configuration. Sweep the whole frequency band through the range from 9 kHz to the 10th harmonic of the carrier, and the emissions less than 20 dB below the permissible value are reported. Set the spectrum analyzer in the following: (a) PEAK: RBW=VBW=3MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=3MHz / Sweep=AUTO This setting method can refer to ANSI C63.10-2013. During the test, below 30MHz, the center of the loop shall be 1 meters; above 30MHz, the height of receive antenna shall be moved from 1 to 4 meters, and the antenna shall be performed under horizontal and vertical polarization. The data of cable loss and antenna factor has been calibrated in full testing frequency range before the testing. Set the spectrum analyzer in the following: Below 1GHz (detector: Peak and Quasi-Peak) RBW=100 kHz / VBW=300 kHz / Sweep=AUTO Above 1GHz (detector: Peak): (a) PEAK: RBW=1MHz VBW=3MHz/ Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=3MHz / Sweep=AUTO The test is in transmitting mode. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 19 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test setup 9KHz ~ 30MHz 30MHz ~ 1GHz Above 1GHz Note: Area side:2.4mX3.6m TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 20 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Limits Rule Part 15.247(d) specifies that “In addition, radiated emissions which fall in the restricted bands, as defined in § 15.205(a), must also comply with the radiated emission limits specified in § 15.209(a) (see § 15.205(c)).” Limit in restricted band Frequency of emission (MHz) Field strength(uV/m) Field strength(dBuV/m) 0.009–0.490 2400/F(kHz) / 0.490–1.705 24000/F(kHz) / 1.705–30.0 30 / 30-88 100 40 88-216 150 43.5 216-960 200 46 Above960 500 54 §15.35(b) There is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit. Peak Limit=74 dBuV/m Average Limit=54 dBuV/m Spurious Radiated Emissions are permitted in any of the frequency bands listed below: TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 21 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96. Frequency Uncertainty 9KHz-30MHz 3.55 dB 30MHz-200MHz 4.02 dB 200MHz-1GHz 3.28 dB Above 1GHz 3.70 dB TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 22 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test Results: The signal beyond the limit is carrier. Zigbee-Channel 11: Peak Zigbee-Channel 11: Average 110 110 100 100 90 90 80 80 FCC RE PK 70 70 2.389980000 GHz 52.059 dBμV/ Level in dBμV/ Level in dBμV/ 60 60 FCC RE AV 50 50 2.389980000 GHz 37.266 dBμV/ 40 40 30 30 20 20 10 10 0 0 2310 2320 2330 2340 2350 2360 2370 2380 2390 2400 2410 2420 2430 2310 2320 2330 2340 2350 2360 2370 2380 2390 2400 2410 2420 2430 Frequency in MHz Frequency in MHz Zigbee-Channel 26: Peak Zigbee-Channel 26: Average 110 110 100 100 90 90 80 80 FCC RE PK 70 2.483500000 GHz 70 69.156 dBμV/ 2.483500000 GHz Level in dBμV/ Level in dBμV/ 60 60 52.064 dBμV/ FCC RE AV 50 50 40 40 30 30 20 20 10 10 0 0 2450 2455 2460 2465 2470 2475 2480 2485 2490 2495 2500 2450 2455 2460 2465 2470 2475 2480 2485 2490 2495 2500 Frequency in MHz Frequency in MHz TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 23 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test result Sweep the whole frequency band through the range from 9kHz to the 10th harmonic of the carrier, the Emissions in the frequency band 9kHz-30MHz and 18GHz-26.5GHz are more than 20dB below the limit are not reported. The following graphs display the maximum values of horizontal and vertical by software. For above 1GHz, Blue trace uses the peak detection, Green trace uses the average detection. During the test, the Radiates Emission from 30MHz to 1GHz was performed in all modes with all channels, Zigbee, Channel 11 are selected as the worst condition. The test data of the worst-case condition was recorded in this report. Continuous TX mode: RE 0.03-1GHz QP Class B 80 70 60 FCC RE QP 50 Level in dBμV/ 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz Radiates Emission from 30MHz to 1GHz Reading Correct Frequency Quasi-Peak Height Azimuth Margin Limit value Polarization Factor (MHz) (dBuV/m) (cm) (deg) (dB) (dBuV/m) (dBuV/m) (dB) 35.410000 13.7 -2.9 100.0 V 0.0 16.6 26.3 40.0 54.377500 10.6 -3.3 100.0 V 324.0 13.9 29.4 40.0 109.938750 11.0 -2.4 200.0 V 0.0 13.4 32.5 43.5 309.927500 12.8 -2.9 200.0 H 0.0 15.7 33.2 46.0 548.912500 19.5 -2.4 100.0 V 4.0 21.9 26.5 46.0 943.335000 26.3 -0.7 200.0 V 138.0 27.0 19.7 46.0 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 24 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Zigbee CH11 FCC RE 1G-3GHz PK+AV Class B 110 100 80 FCC RE PK Level in dBμV/ 60 FCC RE AV 40 20 0 1000 1500 2000 2500 3000 Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz FCC RE 1G-18GHz PK+AV Class B 110 100 80 FCC RE PK Level in dBμV/ 60 FCC RE AV 40 20 0 3 4 6 8 10 12 14 16 18 Frequency in GHz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 25 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Reading Correct Frequency Peak Height Azimuth Margin Limit Polarization value Factor (MHz) (dBuV/m) (cm) (deg) (dB) (dBuV/m) (dBuV/m) (dB) 1166.000000 46.0 200.0 H 320.0 47.0 -1.0 28.0 74 1432.000000 47.0 200.0 H 166.0 46.9 0.1 27.0 74 1691.000000 48.2 100.0 V 343.0 46.5 1.7 25.8 74 2045.500000 50.3 100.0 V 289.0 46.9 3.4 23.7 74 2575.500000 52.5 200.0 H 352.0 46.7 5.8 21.5 74 2939.000000 53.1 200.0 V 152.0 46.7 6.4 20.9 74 Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Reading Correct Frequency Average Height Azimuth Margin Limit Polarization value Factor (MHz) (dBuV/m) (cm) (deg) (dB) (dBuV/m) (dBuV/m) (dB) 1137.500000 34.9 100.0 H 106.0 36.0 -1.1 19.1 54 1439.500000 35.5 200.0 H 224.0 35.3 0.2 18.5 54 1676.500000 36.7 100.0 H 106.0 35.1 1.6 17.3 54 2027.000000 38.5 200.0 H 272.0 35.2 3.3 15.5 54 2570.500000 40.4 200.0 V 56.0 34.6 5.8 13.6 54 2882.000000 41.3 200.0 H 253.0 34.9 6.4 12.7 54 Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 26 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Zigbee CH18 FCC RE 1G-3GHz PK+AV Class B 110 100 80 FCC RE PK Level in dBμV/ 60 FCC RE AV 40 20 0 1000 1500 2000 2500 3000 Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz FCC RE 1G-18GHz PK+AV Class B 110 100 80 FCC RE PK Level in dBμV/ 60 FCC RE AV 40 20 0 3 4 6 8 10 12 14 16 18 Frequency in GHz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 27 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Reading Correct Frequency Peak Height Azimuth Margin Limit Polarization value Factor (MHz) (dBuV/m) (cm) (deg) (dB) (dBuV/m) (dBuV/m) (dB) 1169.500000 46.4 100.0 V 288.0 47.4 -1.0 27.6 74 1400.000000 47.4 200.0 V 0.0 47.4 0.0 26.6 74 1714.000000 47.8 200.0 H 357.0 46.1 1.7 26.2 74 2069.500000 49.8 100.0 H 0.0 46.2 3.6 24.2 74 2585.000000 51.9 100.0 H 0.0 46.0 5.9 22.1 74 2762.500000 52.4 200.0 H 98.0 46.2 6.2 21.6 74 Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Reading Correct Frequency Average Height Azimuth Margin Limit Polarization value Factor (MHz) (dBuV/m) (cm) (deg) (dB) (dBuV/m) (dBuV/m) (dB) 1190.500000 35.0 100.0 H 0.0 35.9 -0.9 19.0 54 1416.000000 36.0 100.0 V 52.0 35.9 0.1 18.0 54 1727.500000 36.9 200.0 H 68.0 35.1 1.8 17.1 54 2050.500000 38.4 100.0 H 260.0 34.9 3.5 15.6 54 2588.500000 40.6 100.0 V 259.0 34.7 5.9 13.4 54 2739.500000 41.3 100.0 V 63.0 35.2 6.1 12.7 54 Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 28 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Zigbee CH26 FCC RE 1G-3GHz PK+AV Class B 110 100 80 FCC RE PK Level in dBμV/ 60 FCC RE AV 40 20 0 1000 1500 2000 2500 3000 Frequency in MHz Note: The signal beyond the limit is carrier. Radiates Emission from 1GHz to 3GHz FCC RE 1G-18GHz PK+AV Class B 110 100 80 FCC RE PK Level in dBμV/ 60 FCC RE AV 40 20 0 3 4 6 8 10 12 14 16 18 Frequency in GHz Radiates Emission from 3GHz to 18GHz TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 29 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Reading Correct Frequency Peak Height Azimuth Margin Limit Polarization value Factor (MHz) (dBuV/m) (cm) (deg) (dB) (dBuV/m) (dBuV/m) (dB) 1167.500000 46.5 100.0 H 72.0 47.5 -1.0 27.5 74 1236.000000 47.3 100.0 V 0.0 48.1 -0.8 26.7 74 1464.500000 47.9 100.0 H 316.0 47.6 0.3 26.1 74 2066.000000 50.1 200.0 H 0.0 46.5 3.6 23.9 74 2679.500000 51.8 100.0 H 226.0 45.8 6.0 22.2 74 2998.500000 52.5 200.0 V 17.0 46.0 6.5 21.5 74 Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) Reading Correct Frequency Average Height Azimuth Margin Limit Polarization value Factor (MHz) (dBuV/m) (cm) (deg) (dB) (dBuV/m) (dBuV/m) (dB) 1140.500000 35.1 200.0 V 45.0 36.2 -1.1 18.9 54 1440.500000 35.5 200.0 V 64.0 35.3 0.2 18.5 54 1707.000000 36.8 200.0 H 0.0 35.1 1.7 17.2 54 2055.000000 38.8 200.0 H 272.0 35.3 3.5 15.2 54 2724.500000 41.1 100.0 H 53.0 35.0 6.1 12.9 54 2983.000000 40.8 200.0 V 0.0 34.4 6.4 13.2 54 Remark: 1. Correction Factor = Antenna factor+ Insertion loss (cable loss + amplifier gain) TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 30 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 5.7. Conducted Emission Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement The EUT is placed on a non-metallic table of 80cm height above the horizontal metal reference ground plane. During the test, the EUT was operating in its typical mode. The test method is according to ANSI C63.10-2013. Connect the AC power line of the EUT to the L.I.S.N. Use EMI receiver to detect the average and Quasi-peak value. RBW is set to 9 kHz, VBW is set to 30kHz. The measurement result should include both L line and N line. The test is in transmitting mode. Test Setup Note: AC Power source is used to change the voltage 110V/60Hz. Limits Frequency Conducted Limits(dBμV) (MHz) Quasi-peak Average 0.15 - 0.5 66 to 56 * 56 to 46* 0.5 - 5 56 46 5 - 30 60 50 *: Decreases with the logarithm of the frequency. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96, U= 2.69 dB. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 31 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Test Results: The equipment doesn’t connect to public network, therefore this requirement does not apply. TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 32 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 6. Main Test Instruments Serial Calibration Expiration Name Manufacturer Type Number Date Date Spectrum Analyzer R&S FSV30 100815 2018-12-16 2019-12-15 EMI Test Receiver R&S ESCI 100948 2018-05-20 2019-05-19 Loop Antenna SCHWARZBECK FMZB1519 1519-047 2017-09-26 2019-09-25 TRILOG Broadband Schwarzbeck VULB 9163 9163-201 2017-11-18 2019-11-17 Antenna Double Ridged Waveguide Horn R&S HF907 100126 2018-07-07 2020-07-06 Antenna Standard Gain Horn ETS-Lindgren 3160-09 00102643 2018-06-20 2020-06-19 EMI Test Receiver R&S ESR 101667 2018-05-20 2019-05-19 LISN R&S ENV216 101171 2016-12-16 2019-12-15 Spectrum Analyzer Agilent N9010A MY47191109 2018-05-20 2019-05-19 RF Cable Agilent SMA 15cm 0001 2018-12-16 2019-03-15 Software R&S EMC32 9.26.0 / / *****END OF REPORT ***** TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 33 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 ANNEX A: EUT Appearance and Test Setup A.1 EUT Appearance Front Side Back Side Part 1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 34 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Front Side Back Side Part 2 Picture 1 EUT TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 35 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 A.2 Test Setup 9KHz-30MHz 30MHz-1GHz TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 36 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: R1812A0593-R1V1 Above 1GHz Picture 2 Radiated Emission Test Setup TA Technology (Shanghai) Co., Ltd. TA-MB-04-012R Page 37 of 37 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.


Document Created: 2019-03-21 13:54:49
Document Modified: 2019-03-21 13:54:49
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC