User Manual

FCC ID: 2AGDVLHL3

Users Manual

Download: PDF
FCCID_4303891




( Function Diagram C LED Display Description 1.0 Outlooks Silicone Grip —I LED Display Throftle Electromagnetic Brake Hook Speed Display Lock / Unlock Front Light Folding Buckle Apa— Speed Gear faial— Error Display Antl—Sllp Sandpaper Front Shock Absorber Widen Pedal Ec ) Kilometer Front Wheel Rear Shock Absorber ————————————— Brake Pedal Kickstand Bluetooth Battery Display * Brake Light Charge Port Brushless Gearless Motor 03 04

2.0 Usage Install Steps ® There is a button key on the display. © is power switch / function switch. m Long pressthe @ switch key, is to turn on/off the power. Short press the @ switch key, <z2"\ +£), C is to turn on/off the front LED light. ® When the meter display is on, short press the switch button to turn on/off the front light. To unfold the scooter body. Step 1: Open the package carton, Step 2: As the picture shows, one hand Step 3: According to the picture, and take out the scooter and tools. press down the rear brake pad; the till the scooter body is unfolding other hand pull up the stem tube. absolutely. 05 06

Install Steps Folding & Dragging Install handlebar Folding Step 4: As pleture shows, connect Step 5: After the cables connected, Step 6: As picture shows, Locking the Step 1: As the picture shows, Step 2: Fold the front fube Step 3: The folding is done. Step 4: When folded, you the cables consistently with the put the handlebar on the down tube, screws on both sides of the stem. foot pressing on the folding to the bottom board, until can take it by single hand. same color. align the screw holes in right position. Then, the handle part is installed . buckle heavily. the small hook on the stem and the hole on the foot brake are completely locked. 07 08

How to use throttle and brake? How to ride? Throfllem Brake Step 1: press the button on the display to power on. Step 2: please ride in flat and open area when the first time to drive. Be sure the scooter unfolded completely, or there is a risk. * Start: pressing the right throttle grip. then you can speed up. * Brake: there‘ s a electromagnetic brake on the left of the handle bar, press it, the e—scooter will be stopped. Besides pressing, step the rear foot brake can make a more efficientstop. * Fixed speed cruise: when ride the scooter in a certain speed and keep it in 6 seconds, the scooter will enter fixed—speed cruise. Then you can loose the throttle and the scooter will keep going in the speed. Step 3: hold the handle bar, put one foot on board, Step 4: put both feet on board while speed up, so that can When you press the throttle again, or press brake, the scooter will exit the speed—fixed mold. and push the e—scooter by the other footto start the e—scooter. keep stable driving. Notice: please release the throttle and brake when turn on the e—scooter. Press the throttle to speed up and balance the scooter while riding. 09 10






Caution: The user is cautloned that changes or modfications not expressly approved by the party responsible for compliance could vold the user‘s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful Interference, and (2) this device must accept any interference recelved, Including Interference that may cause undesired Which kind of LOHAS are you ? operation. I stick to natural gentle sports I closed to nature, prefer organic trips NOTE: This equipment has been tested and found to comply with the limils for a Class B digital device, pursuant to Part 15 of the FCC Rules. These IImits are designed to provide reasonabble protection against harmful Interference in a residentlal Instailation. This equipment Ilove to make difference generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may couse Make life special harmful interference to radio communications. However, there is no guarantee that interference will not occur in a parficular installation. If It‘s a new thinking way for fresh life this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off It‘s a new wave of low—carban transportation and on, theuseris encouraged to try to correct the interference by one or more of thefollowing measures: — Reoient or relocate the receiving antenna.— Increase the separation between the equipment and receiver. — Connect the equipment Into an outlet on a circuit Make difference because of you different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:This equipment compilies with FCC radiation exposure limils set forth for an uncontrolled environment. This transmitfer must not be co—located or operating in conjunction with any other antenna or fransmitter. 21 22


Document Created: 2019-05-07 09:46:08
Document Modified: 2019-05-07 09:46:08
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC