Test Report

FCC ID: 2AGA7MW07L

Test Report

Download: PDF
FCCID_3944186

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Report No.: SZEM180500464503 Fax: +86 (0) 755 2671 0594 Page : 1 of 19 Email: ee.shenzhen@sgs.com 1 COVER PAGE FCC REPORT Application No. : SZEM1805004645CR Applicant: NEW AUDIO LLC. Address of Applicant: 132 W. 31st 7th Floor New York, United States 10001 Manufacturer/ Factory: NEW AUDIO LLC. Address of Manufacturer/ 132 W. 31st 7th Floor New York, United States 10001 Factory: Product Name: MW07 Truewireless Earphone Model No.(EUT): MW07 Trade Mark: Master&Dynamic FCC ID: 2AGA7MW07L Standards: 47 CFR Part 15, Subpart C Date of Receipt: 2018-06-04 Date of Test: 2018-06-12 to 2018-06-20 Date of Issue: 2018-06-25 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. Keny Xu EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 2 of 19 2 Version Revision Record Version Chapter Date Modifier Remark 01 2018-06-25 Original Authorized for issue by: Bill Chen /Project Engineer Eric Fu /Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 3 of 19 2 Test Summary Test Item Test Requirement Test method Result Radiated Spurious 47 CFR Part 15, Subpart C ANSI C63.10 (2013) PASS emissions Section 15.205/15.209 20dB Occupied 47 CFR Part 15, Subpart C ANSI C63.10 (2013) PASS Bandwidth Section This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 4 of 19 3 Contents Page 1 COVER PAGE .......................................................................................................................................... 1 2 VERSION .................................................................................................................................................. 2 2 TEST SUMMARY ..................................................................................................................................... 3 3 CONTENTS .............................................................................................................................................. 4 4 GENERAL INFORMATION ...................................................................................................................... 5 4.1 GENERAL DESCRIPTION OF EUT ............................................................................................................. 5 4.2 TEST ENVIRONMENT AND MODE .............................................................................................................. 6 4.3 DESCRIPTION OF SUPPORT UNITS ........................................................................................................... 6 4.4 TEST LOCATION ...................................................................................................................................... 6 4.5 TEST FACILITY ........................................................................................................................................ 7 4.6 DEVIATION FROM STANDARDS ................................................................................................................. 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ........................................................................................ 7 4.8 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................. 7 4.9 EQUIPMENT LIST ..................................................................................................................................... 8 5 TEST RESULTS AND MEASUREMENT DATA ...................................................................................... 9 5.1 RADIATED EMISSION ............................................................................................................................... 9 5.2 20DB OCCUPY BANDWIDTH ................................................................................................................... 16 6 PHOTOGRAPHS - EUT TEST SETUP .................................................................................................. 18 6.1 RADIATD EMISSION (30MHZ-1000MHZ) ................................................................................................ 18 6.2 RADIATED SPURIOUS EMISSION (BELOW 30MHZ) .................................................................................. 19 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 5 of 19 4 General Information 4.1 General Description of EUT Power supply: Left ear: Li-ion rechargeable battery DC 3.7V Cable: Type C cable:96cm unshielded Operation Frequency: 10.54MHz Antenna Type: Loop Antenna This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM1s0s004s4503 Page sot 19 4.2 Test Environment and Mode Operating Environment Temperature mo‘o Homay s57.m Amospharic Fressure: 1010 mbar Test mode: T mode Keep te EUT inransmiting mode 4.3 Description of Support Units "The EUT has been tested wih ascocited equipment below Deseripton Manutacturer Model No: Adapter Accle »i57 worntost 4.4 Test Location Alltests were perfomed at 868—08TG Standards Technial Services Co., Lid. Shonzhen Branch No. 1 Workshap, M—10, MSecton, Science & Technology Park,Shenzhen, Guangdong, Chine. steosr. Tok +8755 2e01 2089 Fax «85 7os 2eriosna rnnonptsmntersorenc Ipuoredommone un e orctnc ninrnconomvimon nimointome mtpoounool oconormntercmmnrc leceecemen ecncetname temiel

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 7 of 19 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G- 20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 4.6 Deviation from Standards None. 4.7 Abnormalities from Standard Conditions None. 4.8 Other Information Requested by the Customer None. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 8 of 19 4.9 Equipment List RE in Chamber Cal. Date Cal. Due date Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) (yyyy-mm-dd) 10m Semi-Anechoic SAEMC FSAC1018 SEM001-03 2018-03-31 2021-03-30 Chamber EMI Test Receiver Rohde & Schwarz ESR SEM004-03 2018-04-02 2019-04-01 (9k-7GHz) Trilog-Broadband Antenna Schwarzbeck VULB9168 SEM003-18 2016-06-29 2019-06-28 (30M-1GHz) Pre-amplifier Sonoma 310N SEM005-04 2018-04-13 2019-04-12 (9kHz-1GHz) Instrument Co Loop Antenna ETS-Lindgren 6502 SEM003-08 2017-08-22 2020-08-21 (9kHz-30MHz) Measurement Software AUDIX e3 V8.2014-6-27 N/A N/A N/A Coaxial Cable SGS N/A SEM029-01 2017-07-13 2018-07-12 Conducted Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date DC Power Supply RXN-305D ZhaoXin SEM011-02 2017-09-27 2018-09-26 Spectrum Analyzer FSP Rohde & Schwarz SEM004-06 2017-09-27 2018-09-26 JS1120-2 Measurement Software JS Tonscend N/A N/A N/A BT/WIFI V2. Coaxial Cable SGS N/A SEM031-02 2017-07-13 2018-07-12 Attenuator Weinschel Associates WA41 SEM021-09 N/A N/A Signal Generator KEYSIGHT N5173B SEM006-05 2017-09-27 2018-09-26 Power Meter Rohde & Schwarz NRVS SEM014-02 2017-09-27 2018-09-26 General used equipment Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-03 2017-09-29 2018-09-28 Indicator Industry Factory Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-04 2017-09-29 2018-09-28 Indicator Industry Factory Humidity/ Temperature Mingle N/A SEM002-08 2017-09-29 2018-09-28 Indicator Changchun Barometer Meteorological DYM3 SEM002-01 2018-04-08 2019-04-07 Industry Factory This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 9 of 19 5 Test results and Measurement Data 5.1 Radiated Emission Test Requirement: 47 CFR Part 15C Section 15.209 and 15.205 Test Method: ANSI C63.10: 2013 Test Site: Measurement Distance: 10m (Semi-Anechoic Chamber) Receiver Setup: Frequency Detector RBW VBW Remark 30MHz-1GHz Quasi-peak 100kHz 300kHz Quasi-peak Value Above 1GHz Peak 1MHz 3MHz Peak Value Limit: Field strength Limit Measurement Frequency Remark (microvolt/meter) (dBuV/m) distance (m) 0.009MHz-0.490MHz 2400/F(kHz) - - 300 0.490MHz-1.705MHz 24000/F(kHz) - - 30 1.705MHz-30MHz 30 - - 30 30MHz-88MHz 100 40.0 Quasi-peak 3 88MHz-216MHz 150 43.5 Quasi-peak 3 216MHz-960MHz 200 46.0 Quasi-peak 3 960MHz-1GHz 500 54.0 Quasi-peak 3 Above 1GHz 500 54.0 Average 3 Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 and 10 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter full-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 or 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 10 of 19 specified and then reported in a data sheet. h. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, and found the X axis positioning which it is the worst case. i. Repeat above procedures until all frequencies measured was complete. Test Setup: Figure 1. 30MHz to 1GHz Instruments Used: Refer to section 4.10 for details Test Mode: NFMI mode Test Results: Pass Field Strength Of The Fundamental Signal Antenna Preamp Read Level Level Limit Line Over Frequency Cable Polari Factor Factor Level @10m @ 30m @ 30m Limit (MHz) Loss (dB) zation (dB/m) (dB) (dBuV) (dBuV/m) (dBuV/m) (dBuV/m) (dB) 10.54 0.50 10.66 32.90 55.05 33.31 4.69 29.5 -24.81 H 10.54 0.50 10.66 32.90 53.84 32.10 3.48 29.5 -26.02 V This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 11 of 19 Below 30MHz QP value:0.009MHz-0.15MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 12 of 19 QP value:0.15MHz-30MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 13 of 19 QP value: 30MHz~1GHz Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 14 of 19 Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 15 of 19 Below 1GHz The test was performed at a 10m test site. According to below formulate and the test data at 10m test distance, L3 / L10 = D10 / D3 Note: L3: Level @ 3m distance. Unit: uV/m; L10: Level @ 10m distance. Unit: uV/m; D3: 3m distance. Unit: m D10: 10m distance. Unit: m The level at 3m test distance is below: Level @ Frequency Level @ Level @ 3m Level @ 3m Limit @ 3m Ant. 10m Margin (dB) (MHz) 10m (uV/m) (uV/m) (dBuV/m) (dBuV/m) Polarization (dBuV/m) 41.86 13.89 4.95 16.50 24.35 40.00 -15.65 H 167.24 14.38 5.24 17.45 24.84 43.50 -18.66 H 301.42 16.10 6.38 21.28 26.56 46.00 -19.44 H 497.68 20.12 10.14 33.80 30.58 46.00 -15.42 H 645.12 23.81 15.51 51.69 34.27 46.00 -11.73 H 903.31 27.38 23.39 77.96 37.84 46.00 -8.16 H 39.16 21.09 11.34 37.79 31.55 40.00 -8.45 V 46.34 20.82 10.99 36.63 31.28 40.00 -8.72 V 168.41 20.02 10.02 33.41 30.48 43.50 -13.02 V 199.29 19.88 9.86 32.88 30.34 43.50 -13.16 V 227.69 20.15 10.17 33.91 30.61 46.00 -15.39 V 303.54 24.52 16.83 56.09 34.98 46.00 -11.02 V Remark: 1)The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: 2)Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor 3)Emissions from 9kHz to 30 MHz is too low to be find, so it is not reported. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 16 of 19 5.2 20dB Occupy Bandwidth Test Requirement: 47 CFR Part 15C Test Method: ANSI C63.10:2013 Section 7.8.7 Test Setup: Limit: NA Final Test Mode: Transmitting mode Instruments Used: Refer to section 5.10 for details Test Results: Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 17 of 19 Measurement Data Test channel 20dB Occupy Bandwidth (kHz) 10.54MHz 548 * RBW 10 kHz Delta 1 [T1 ] * VBW 30 kHz -0.16 dB Ref -20 dBm * Att 0 dB SWT 10 ms 548.000000000 kHz -20 Marker 1 [T1 ] -67.83 dBm 10.302000000 MHz A -30 Marker 2 [T1 ] 1 PK -46.99 dBm VIEW -40 10.501000000 MHz 2 -50 -60 1 1 D1 -66.99 dBm -70 3DB -80 -90 -100 -110 -120 Center 10.54 MHz 100 kHz/ Span 1 MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 18 of 19 6 Photographs - EUT Test Setup 6.1 Radiatd Emission (30MHz-1000MHz) This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180500464503 Page : 19 of 19 6.2 Radiated Spurious Emission (Below 30MHz) - End of the Report - This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2018-07-27 02:14:48
Document Modified: 2018-07-27 02:14:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC