User manual

FCC ID: 2AG32U4GUE1305

Users Manual

Download: PDF
FCCID_4501834

u4G-UE1305 Indoor USB Dongle Specification

Introduction Baicells is a private, high-tech company providing innovative LTE wireless broadband access solutions. The Baicells solutions support fixed wireless access and mobile scenarios. With the vision to connect the unconnected, Baicells has introduced breakthrough technologies to LTE, like moving a complete LTE system to special spectrum and building it with an IT based architecture. With the Baicells turnkey end-to-end solutions, it becomes much easier to provide wireless internet within everyone's reach at a very low cost. These innovative solutions can be used by mobile operators, broadband access operators, Internet Service Providers (ISP), Mobile Virtual Network Operators (MVNO), governments, and enterprise private networks. The Baicells u4G-UE1305 B53 USB-dongle is a type of LTE indoor device working on B53 licensed frequency, which provides superior wireless access performance and comprehensive routing capabilities to bring wireless broadband data to end -users. It can be connected with the USB interface of a computer by the USB Cable and then converts high-speed LTE TDD signals on the USB interface. The typical topology of u4G-UE1305 B53 USB-dongle deployment is as follows, which solution provides wireless broadband and wired Ethernet data services for customers. 1

Highlights  Supports LTE-TDD frequency bands 53.  Complies with 3GPP Release 9 CAT4 standards.  USB 2.0 interface.  Convenient, simple, GUI-based local Web management. 2

Basic Specifications Item Description UE-Category 3GPP R9, CAT 4 USIM Slot 1.8V/3.0V USIM 2FF Ethernet Port 1 USB 2.0 port Power Supply USB Input: 5V/0.8A LED Indicators SIM/PWR/LTE Signal Dimensions (L)88mm x (W)45mm x (H)18mm (without antenna) Weight About 200g 3

LTE Specifications Item Description LTE Mode TDD LTE Bands B53 DL/UL : 2483.5MHz ~ 2495MHz TXRX 1T2R  10MHz: SA1: DL 40 Mbps, UL 6.8 Mbps SA2: DL 54 Mbps, UL 3.4 Mbps Peak Rate  5MHz: SA1: DL 20 Mbps, UL 3.3 Mbps SA2: DL 27 Mbps, UL 1.6 Mbps Channel Bandwidth 5MHz/10MHz UL: QBSK, 16QAM Modulation DL: QBSK, 16QAM, 64QAM Receive Sensitivity -95dBm @ QPSK, 10MHz, 25°C MAX Output Power 22dBm (±2)/TX ANT Antenna Type Integration Antenna Gain 3dBi 4

SW Specifications Item Description Language Support English IP Protocol IPv4 Network Connection Management Auto/Manual  Date & Time setting  Reboot Maintenance  Restore factory settings  Restore / Back up configuration file  Firmware upgrade locally  Operating Log System Log  Run-time Log  Filter/Select/Display/Export Log Antenna Select NC Environmental Specifications Item Description Operating Temperature -5°C to 45°C Storage Temperature -40°C to 70°C Operating Humidity 5% to 95% IP Level Indoor using 5

Model List Models Description B53 USB-dongle ( LTE USB-dongle, TDD B53, CAT4, u4G-UE1305 1T2R, 1 USB2.0 ) FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Warning: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 6


Document Created: 2019-11-04 15:51:45
Document Modified: 2019-11-04 15:51:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC