SAR_Test_Report_Part3

FCC ID: 2AFZZC3JH

RF Exposure Info

Download: PDF
FCCID_4403714

® In Collaboration with m TTL S e _a @a CALIBRATION LABORATORY uy Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitpi//www.chinattl.on Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY52 52.8.8.1258 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4 mm, dz = 1.4 mm Graded Ratio = 1.4 (Z direction) 5250 MHz £1 MHz Frequency 5600 MHz 1 MHz 5750 MHz 41 MHz Head TSL parameters at 5250 MHz Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.71 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.4 £6 % 4.64 mho/m £ 6 % Head TSL temperature change during test <1.0 °C ~~— ———— SAR result with Head TSL at 5250 MHz SAR averaged over 1 Cm° (1 g) of Head TSL Condition SAR measured 100 mW input power 7.87 mW /g SAR for nominal Head TSL parameters normalized to 1W 78.4 mW ig £ 23.0 % (k=2) SAR averaged over 10 cm2" (10 g) of Head TSL Condition SAR measured 100 mW input power 2.25 mW /g SAR for nominal Head TSL parameters normalized to 1W 22.4 mW 1g & 22.2 % (k=2) Certificate No: Z17—97001 Page 3 of 14

.mm In Collaboration with T"TL a_ v CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitpil/www.chinattl.en Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mhoim Measured Head TSL parameters (22.0 £0.2) °C 354 +6 % 5.02 mho/m £ 6 % Head TSL temperature change during test <1.0 °C —— ———— SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm° (1 g) of Head TSL Condition SAR measured 100 mW input power 8.16 mw/g SAR for nominal Head TSL parameters normalized to 1W 81.5 mW /g * 23.0 % (k=2) SAR averaged over 10 Ci" (10 g) of Head TSL Condition SAR measured 100 mW input power 2.32 mW /g SAR for nominal Head TSL parameters normalized to 1W 23.2 mW /g £ 22.2 % (k=2) Head TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.4 5.22 mho/m Measured Head TSL parameters (22.0 £0.2) °C 36.1 46 % 5.17 mho/m +6 % Head TSL temperature change during test <1.0 °C ——— ——— SAR result with Head TSL at 5750 MHz SAR averaged over 1 Cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.02 mW /g SAR for nominal Head TSL parameters normalized to 1W 80.5 mW /g + 23.0 % (k=2) SAR averaged over 10 cm> (10 g) of Head TSL Condition SAR measured 100 mW input power 2.26 mW /g SAR for nominal Head TSL parameters normalized to 1W 22.7 mW ig £ 22.2 % (k=2) Certificate No: Z17—97001 Page 4 of 14

fi I;Collabomfionewith § n a CALIBRATION LABORATORY s Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp://www.chinattl.cn Body TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.36 mho/m Measured Body TSL parameters (22.0 £0.2) °C 47.8 £ 6 % 5.39 mho/m + 6 % Body TSL temperature change during test <1.0 °C ———— ——— SAR result with Body TSL at 5250 MHz SAR averaged over 1 Cm2" (1 g) of Body TSL Condition SAR measured 100 mW input power 7.59 mW /g SAR for nominal Body TSL parameters normalized to 1W 75.6 mW /g £ 23.0 % (k=2) SAR averaged over 10 cm" (10 g) of Body TSL Condition SAR measured 100 mW input power 2.15 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.4 mW Ig * 22.2 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 £0.2) °C 484 +6 % 5.70 mho/m £ 6 % Body TSL temperature change during test <1.0 °C ———— ——— SAR result with Body TSL at 5600 MHz SAR averaged over 1 Cm° (1 g) of Body TSL Condition SAR measured 100 mW input power 8.03 mW /g SAR for nominal Body TSL parameters normalized to 1W 80.2 mW /g + 23.0 % (k=2) SAR averaged over 10 cm> (10 g) of Body TSL Condition SAR measured 100 mW input power 2.23 mW /g SAR for nominal Body TSL parameters normalized to 1W 22.3 mW /g # 22.2 % (k=2) Certificate No: Z17—97001 Page 5 of 14 se y en enc en snn en en e se y

® In Collaboration with _‘]/"]}J, @a v CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitpi//www.chinattl.en Body TSL parameters at 5750 MHz Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.3 5.94 mho/m Measured Body TSL parameters (22.0 £0.2) °C 48.6 46 % 5.83 mho/m + 6 % Body TSL temperature changeduring test «1.0 °C ——— —— SAR result with Body TSL at 5750 MHz SAR averaged over 1 cm° (1 g) of Body TSL Condition SAR measured 100 mW input power 7.46 mW /g SAR for nominal Body TSL parameters normalized to 1W 74.6 mW ig & 23.0 % (k=2) SAR averaged over 10 Cm" (10 g) of Body TSL Condition SAR measured 100 mW input power 2.10 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.0 mW 1g £ 22.2 % (k=2) Certificate No: Z17—97001 Page 6 of 14

zi Y v es CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitpi//mww.chinattl.en Appendix Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point 48.40 — 5.62j0 Return Loss —24.5dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point §5.50 — 5.3910 Return Loss —22.80B Antenna Parameters with Head TSL at 5750 MHz Impedance, transformed to feed point 52.40 — 4.200 Return Loss —26.5dB Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 50.40 — 5.8610 Return Loss —24.70B Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 57.20 — 1.5910 Return Loss —23.30B Antenna Parameters with Body TSL at 5750 MHz Impedance, transformed to feed point 56.00 — 0.37j0 Return Loss —24.90B Certificate No: Z17—97001 Page 7 of 14 C omm ns hn en en esnt es n g n en n ce en nn mc cssy 22

® In Collaborationwith Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail; cttl@chinattl.com http://wwwchinattl.en General Antenna Parameters and Design Electrical Delay (one direction) 1.310 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z17—97001 Page 8 of 14

® In Collaboration with a_®/"]7°J, a_ imz CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en DASY5 Validation Report for Head TSL Date: 01.05.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1151 Communication System: CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Medium parameters used: f = 5250 MHz; 0 = 4.636 mho/m; er = 35.38; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 5.015 mho/m; er = 35.41; p = 1000 kg/m3, Medium parameters used: f= 5750 MHz; 0 = 5.173 mho/m; &r = 36.06; p = 1000 kg/m3, Phantom section: Center Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN7433; ConvF(5.13,5.13,5.13); Calibrated: 2016/9/26, ConvF(4.59,4.59,4.59); Calibrated: 2016/9/26, ConvF(4.66,4.66,4.66); Calibrated: 2016/9/26, * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn771; Calibrated: 2016/2/2 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/3 * Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration /Pin=100mW, d=10mm, f=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 71.52 V/m; Power Drift = 0.07 dB Peak SAR (extrapolated) = 32.1 W/kg SAR(1 g) = 7.87 Wikg; SAR(10 g) = 2.25 Wikg Maximum value of SAR (measured) = 18.3 Wikg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 58.03 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 34.2 Wi/kg SAR(1 g) = 8.16 Wikg; SAR(10 g) = 2.32 Wikg Maximum value of SAR (measured) = 19.9 Wikg Certificate No: Z17—97001 Page 9 of 14

® In Collaboration with Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en Dipole Calibration /Pin=100mW, d=10mm, f=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 58.85 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 35.0 Wikg SAR(T g) = 8.02 Wikg; SAR(10 g) = 2.26 Wikg Maximum value of SAR (measured) = 19.7 W/kg —10.00 —20.00 —30.00 ~40.00 ~50.00 0 dB = 19.7 Wikg = 12.94 dBW/kg Certificate No: Z17—97001 Page 10 of 14

A“ In Collaboration with m_‘/"]"J, p_e_a imggyee CALUIBRATION LABORATO Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitpi//www.chinattl.en Impedance Measurement Plot for Head TSL Tri S11 Log Mag 10.00d8/ Ref 0.000d8 [F2] 509 1x 32500000 ane <20.337 ds 2_5.6000000 anz 2221752 de 40. 00— 53~—527500000"GHz =261 507dn mm i 30.00 |— > colzl 20.00 — 10. 00 0. 000 pj — w ~10.00 =20.00 ~20.00 000 |ceorm—ommnmecpenninpnecnenech woieteeins ~50. 00 MBR Si1 smith (R+Jx) scale 1.000u [F1 bel] 1 $.2500000 cz 48.398 n —5.6224 n 5.3918—p 2 $.9000000 ahz 55.486 n ~5.3942 n 5.2687 pr >3 5.7500000 GHiz 52.426 0 —4.1955 o $75974 pF Certificate No: Z17—97001 Page 11 of 14

difp®®> n Collsboration with aw7/"7}]J, a V CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail; cttl@chinattl.com hitp://www.chinattl.en DASY5 Validation Report for Body TSL Date: 01.04.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1151 Communication System: CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Medium parameters used: f = 5250 MHz; a = 5.388 mho/m; er = 47.81; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 5.704 mho/m; er = 48.39; p = 1000 kg/m3, Medium parameters used: f = 5750 MHz; 0 = 5.833 mho/m; er = 48.61; p = 1000 kg/m3, Phantom section: Right Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN7433; ConvF(4.68,4.68,4.68); Calibrated: 2016/9/26, ConvF(3.98,3.98,3.98); Calibrated: 2016/9/26, ConvF(4.35,4.35,4.35); Calibrated: 2016/9/26, Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 Sn771; Calibrated: 2016/2/2 Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/3 Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration /Pin=100mW, d=10mm, f=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 63.69 V/m; Power Drift = —0.05 dB Peak SAR (extrapolated) = 28.5 W/kg SAR(1 g) = 7.59 Wikg; SAR(10 g) = 2.15 Wikg Maximum value of SAR (measured) = 17.7 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.67 V/m; Power Drift = —0.05 dB Peak SAR (extrapolated) = 33.8 W/kg SAR(1 g) = 8.03 Wikg; SAR(10 g) = 2.23 Wikg Maximum value of SAR (measured) = 19.8 W/kg Certificate No: Z17—97001 Page 12 of 14

Afl In Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitpi//wwrw.chinattl.en Dipole Calibration /Pin=100mW, d=10mm, f=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 64.76 V/im; Power Drift = —0.04 dB Peak SAR (extrapolated) = 30.0 W/kg SAR(1 g) = 7.46 W/kg; SAR(10 g) = 2.1 Wikg Maximum value of SAR (measured) = 17.5 W/kg ~10.00 ~20.00 ~30.00 ~40.00 ~50.00 0 dB = 17.5 Wikg = 12.43 dBW/kg Certificate No: Z17—97001 Page 13 of 14

fffpm®~> in Colleboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com httpi//www.chinattl.on Impedance Measurement Plot for Body TSL Tri S11 Log Mag 10.00d8/ Ref 0.000d5 [F1 bel] 590 13—5,2500000 onz <26.664 dB so.00 256000000ahz123258 de | +80 (e§~~§57e00000~dig" dBH1 BGg gg— O O99 ommnmefemnemernisntsdienmemmins ies nsm memmnssninisecrnmnnen §0.00 L————«— memmee eneduseismoes dutyine — Praticte $0.0§ |_oummorkeurecemmeduce s $0200. [ienmmmnstimssim 0. 000 pl ———— > | ; j C —10.00 |. .=——— i ~20.00 ~30. 00 ~40.00 —50. 00 e BM 5i1 smith (R+JX) scale 1.000u [F1 pel] 1 $.2500000 GHz 50.420 n —5.8648 n 5.1 2 $.6000000 GHz 57.194 n —1.5917 o >3 5.7500000 anz 56.022 o ~365.51 m Certificate No: Z17—97001 Page 14 of 14

Calibration Laboratory of Schwelzerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerand Swiss Calibration Service Accredied by the Sss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Mutilateral Agreement for the recognition of calibration certificates Client TA—SH (Auden) Certificate No: DAE4—1291_Dec18 CALIBRATION CERTIFICATE Onject DAE4 — SD 000 DO4 BM — SN: 1291 Caltration procedure(s) QA CAL—06.v29 Calibration procedure for the data acquisition electronics (DAE) Caltbration aate December 04, 2018 This calbrabon certiicate documents the traceabilty to national standards, which reallze the physical units of measurements (S1). The measurements and the uncertainties with confidence probabily are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facilty: environment temperature (22 + 3)°C and humidity « 70%, Calibraton Equipmentused (METE entical for caltbration) Primary Standards iD# Cal Date (Certficate No.) Schedulad Caltbration Keithiey Muttimeter Type 2001 SN; 0810278 03—Sep—18 (No:#23488) Sep—19 Secondary Standards 10 # Chack Date (in house) Schedulad Chack Auto DAE Calibration Unit SE UWS 053 AA 1001 O4~Jan—18 (in housa chack) In house check: Jan—19 Caltbrator Box V2.1 SE UMS 006 AA 1002 04—Jan—18 (in house chack) In house check: Jan—19 Name Function Signature Callbrated by: Dominique Steffen Laboratory Technician ,@ Approved by: (Sven Kahn Deputy Manager iEHZ Issued: Decamber 4, 2018 This calibration certiicate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE4—1291_Dec18 Page 1 of 5

Calibration Laboratory of Schweizerischer Kalibriardienst Schmid & Partner Service sulsse d‘étalonnage Engineering AG Servizio svizzero di taratura Zoughausstrasse 43, 004 Zurich, Switzerland Swiss Callbration Service Accregited by the Smss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swisz Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calitration cortificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters «_ DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. * Connector angle: The angle of the connectoris assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. «_ DC Voltage Measurement Linearity: Veritication of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. «_ Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. * Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. «_ AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage «_ Input Offset Measurement Output voltage and statistical results over a large numberof zero voltage measurements. «_ Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. ® Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. ® Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. * Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—1291_Dec18 Page 2 of 5

C DC Voltage Measurement A/D — Converter Resolution nominal High Range: 115B = 6.1uV . tull range = »100.,.+300 mV Low Range: 1LSO = 61nV . fult range = ~1...... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y¥ 2 High Range 402.580 + 0.02%(k=2) 408.249 + 0.02% (k=2) 408.168 £0.02% (k=2) Low Range 3.97560 + 1.50% (k=2) 3.97886 + 1.50%(k=2) 2.97558 £ 1.50% (k=2) Connector Angle [ Connector Angle to be used in DASY system 164.5°%41° Certificate No: DAE4—1291_Dec18 Page 3 of 5

C Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (V) Difference (uV) Error (%) Channel X + Input 200038.51 1.95 0.00 Channel X + Input 20006.61 1.29 0.01 Channel X >Input —20003.34 2.04 —0.01 Channet Y + Input 200036.77 0.05 0.00 Channel Y + Input 20003.65 +1.54 —0.01 Channel Y «Input +20006.11 0.22 —0.00 Channel Z + Input 200035.08 ~1.41 —0,00 Channel Z + Input 20002.62 —2.58 —0.01 Channel Z +Input +20006.40 —0.06 0.00 Low Range Reading (V) Difference (uV) Error (%) Channel X + Input 2001.29 0.31 0.02 Channel X + Input 201.13 0.32 0.16 Channel X —Input ~198.59 0.30 —0.15 Channel Y + Input 2000.40 —0.49 —0.02 Channel Y + Input 200.21 —0.66 —0.33 Channel Y — Input +199.89 —0.99 0.50 Channel Z + Input 2000.44 +0.41 —0.02 Channel Z + Input 199.70 +1.05 —0.52 Channel Z — Input —200.88 —1.78 0.839 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 seo; Measuring time: 3 see Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (1V) Channel X 200 10.02 7.91 +200 —5.52 —8.20 Channel Y 200 14.18 13.58 +200 ~15.10 —15.62 Channel Z 200 —17.07 ~17.23 —200 14.74 14.83 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuringtime: 3 see Input Voltage (mV) Channel X (iV) Channel Y (pV) Channel 2 (uV) Channel X 200 3 —0.01 4.47 Channel ¥ 200 7.58 > 0.48 Channel 2 200 11.17 4.87 — Certificate No: DAE4—1291_Dec18 Page 4 of 5

C 4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec: Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 16117 16241 Channel Y 15930 16718 Channel Z 16177 17128 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MG Average (wV) min. Offset(uV) max. Offset (uy) * E::“,’;’"“" Channel X —0.59 ~1.81 0.89 0.47 Channel Y 147 —0.04 2.05 0.45 Channel Z 112 2.70 0.51 0.57 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25tA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 8. Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vee) +7.9 Supply (— Vee) —7.6 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Vee) +0.01 +6 +14 Supply (— Vee) —0.01 —8 9 Certificate No: DAE4—1291_Dec18 Page 5 of 6


Document Created: 2019-08-16 16:51:31
Document Modified: 2019-08-16 16:51:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC